熔流焊接 的英文怎麼說

中文拼音 [róngliúhànjiē]
熔流焊接 英文
fluid welding
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. Specially for welding of thin and mid - thickness steel ; suitable for mag co2 welding of low carbon steel and low alloy steel inner wire feeder structure ; zx5 series thyristor dc arc welder ac arc welder with single phase moveable coil for sma mma welding ; suitable for welding low carbon steel, low alloy steel ; suitable for welding mid - thickness steel

    可用於所有牌號焊條的直接手工電弧焊接引弧容易，無須用戶調節可遠距離調節焊接電流，便於焊工操作焊機動特性好，性能柔和，電弧穩定焊接熔池平靜，飛濺小，不咬邊，焊縫成形美觀。
  2. It has important significance to study the welding technology of variable polarity pulsed mig for high efficiency weding and good quality of welding products. we should control the welding current, output voltage and the process of melting drop more effectively

    研究薄板鋁合金變極性脈沖mig焊接技術，更有效地控制焊接電流、電壓輸出和熔滴過渡過程，提高焊接過程的穩定性、提高焊接速度，對于提高焊接效率和焊接產品質量具有重要的意義。
  3. Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting ". under the condition of constant diameter of welding wire and its feeding speed, the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply. if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition, the welding process will be stable with less spatter and smooth weld bead

    通過分析不同焊接規范下的焊接電壓和電流的波形.研究了水蒸氣保護下電弧及熔滴過渡的特點，發現其電弧過程行為有「燃弧?熄弧?短路」和「燃弧?短路」兩種形式.在焊絲直徑和送絲速度一定的情況下，通過調節焊接迴路中的電感量和電源電壓，可以改變電弧的過程行為形式.若電弧過程呈「燃弧?熄弧?短路」交替進行，並且熄弧時間最短時，短路過渡頻率最高，在這種情況下，飛濺小，焊道成型好，焊接過程穩定
  4. Due to two work states - - - arc burning and short current - - - existed in welding process of consumable electrode welding, and different control objectives in these two states, two close - loop feedbacks are designed in the control system : welding voltage feedback and welding current change rate feedback

    根據熔化極co2焊機具有燃弧和短路兩種工作狀態，且兩種狀態下控制目標不同的特點，在控制系統中設計了雙閉環反饋：焊接電壓反饋及焊接電流變化率di / dt反饋。
  5. When the welding current is added, the fusion quality of welding stick will increase, so the weld reinforcement also will increase

    焊接電流增加時，焊絲的熔化量也增加，因此焊縫的余高也隨之增加。
  6. Electron beam welding is an advanced welding technology, which fusing metal with heat energy which caused by convergent high speed electron stream bombarding joint of work pieces

    電子束焊接是一種在真空環境下，利用匯聚的高速電子流轟擊工件接縫處產生的熱能，使被焊金屬熔合的焊接方法。
  7. Yttrium tungsten is primarily used in military and aviation industry with narrow arc beam, high compressing strength, highest welding penetration at medium and high current

    在焊接時，弧束細長，壓縮程度大，在中大電流時其熔深比較大。目前主要應用於軍事工業和航空航天工業。
  8. When the welding current is added, on the one hand, the section of arc will more or less increase, so the fusion width will increase ; on the other hand, the depth of arc crater will increase

    焊接電流增加時，一方面是電弧截面略有增加，導致熔寬增加，另一方面是電流增加促使弧坑深度增加。
  9. When the welding current is added, the quality of heat of the arc will increase, so both the volume of molten puddle and the depth of arc crater will all increase, and the weld depth will increase when the weld is cooling

    焊接電流增加時，電弧的熱量增加，因此熔池體積和弧坑深度都隨電流增加，所以冷卻下來后，焊縫厚度就增加。
  10. A fuzzy controller with two input variables and one output variable is considered to be suitable to control weld pool width. the input variables of the fuzzy controller are the variation of the welding pool width and its rate, and the output variable is the welding currert

    本文對熔寬模糊控制器的結構以及模糊控制變量的選擇進行了討論，在此模糊控制系統中採用雙輸入單輸出的模糊控制器模型，即採用熔寬的變化及其變化率作為模糊控制器的兩輸入量，採用焊接電流作為模糊控制器的輸出量。
分享友人
分享到 Line

分享到臉書