熔解溫度 的英文怎麼說
中文拼音 [róngjiěwēndù]
熔解溫度
英文
fluxing temperature-
The imported transparent glaze fired at lower temperature was analysed semi - quantitatively by adopting emission spectroscope. the stripping of lead and cadmium from this transparent glaze fired at lower temperature in ceramic product was determined by atomic absorption spectroscope. the effect of chemical composition on the stripping of lead and cadmium was analysed. upon the author s opinion, the overproof lead stripping from the imported transparent glaze fired at lower temperature can only be settled by adopting lead - free glaze instead of adopting low - lead prescription. the author succeeded in developing an excellent lead - free transparent glaze fired at the lower temperature of 1000 1050. the success is based on an inquiry into the feasibility of using such new agents of fusion as li2o and sro in replacement of pbo ; and on a study of the effects of the contents of sio2 ， al2o3 ， b2o3and other metallic oxides on such performances of glaze as coefficient of linear expansion, fusion temperature and transparency. it is also based on an analysis of coefficient of linear expansion of blank and glaze on an analysis of coefficient of linear expansion of blank and glaze on their correlation ; and on a study of technology for preparing glaze
採用發射光譜儀對進口低溫透明釉進行半定量分析，並用原子吸收光譜儀測定其陶瓷製品的鉛、鎘的溶出量，分析化學成分對鉛、鎘溶出量的影響.結果表明，進口低溫透明釉採用低鉛配方不能解決鉛溶出量的超標問題，只有採用無鉛釉才能解決.探討用氧化鋰和氧化鍶等新型熔劑完全代替氧化鉛的工藝，研究釉料中氧化硅、氧化鋁、氧化硼和各種金屬氧化物的含量，對釉的線膨脹系數、熔融溫度和透明度等性能的影響.分析坯料、釉料的線膨脹系數及其相互關系和釉料制備的工藝，研製出優質的1000 1050低溫無鉛透明釉To determine the recommended wattage capabilities of the elements start with figure 1
要測算其理想的負荷能量看圖1后，了解到將在何種熔爐溫度和大氣環境下進行溫控。The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。Abstract : during the heating of scrap with carbon or hydrocarbon contented substances in some process, it will bring problems like explosion of carbon monoxide, fume and smell from oil volatilization, etc. ， if incomplete combustion occurs. through laboratory experiments, the time related variation of gas contents and post combustion ratio of fume during the heating of oil - bearing scrap are studied. the results show that the restrictive chain of reaction procedure is the thermolysis of oil ; that temperature and ( co ) / ( co2 ) ratio influence transformation ratio and post - combustion ratio under lower temperature ; that 900 is the temperature above which the complete reaction can be ensured at all ( co ) / ( co2 ) ratios
文摘:在某些廢鋼熔煉過程中，當爐料中含碳及碳氫物質且燃燒不充分時，會帶來煙氣中一氧化碳的燃爆、油污揮發時造成的煙霧、臭味等問題.通過實驗室裝置研究含油廢鋼在加熱過程中煙氣成分隨時間的改變以及二次燃燒率的變化，試驗結果表明，反應過程的限制性環節是油分的熱分解；在較低的溫度下（ co ） / （ co2 ）比例影響轉化率和二次燃燒率；而在任意比例下保證充分反應的溫度為900以上We apply the system to the ultra - fine grain steel welding, the simulated mean grain size in cghaz agreed well with the corresponding independent experimental data. in this paper, three factors influencing the grain growth, the steep temperature gradient in haz. the grain boundary liquid and the precipitates particle, were studied specially using mc technique
研究表明溫度梯度造成的「熱釘扎」現象和晶界液化現象都對靠近熔合線附近的晶粒長大有明顯的阻礙作用，對最終的晶粒大小分佈有重要的影響：而800mpa超細晶粒鑰中的tin粒子山于溶解溫度高，抑制奧氏體晶粒長大的效果十分顯著。Studying the heat - mass transfer and multi - spices electric - chemical reaction, a dynamic temperature model was deduced for molten - carbonate fuel cell stack. the thermal radiation, shift reaction, and the change of gas spices were considered in this model. establishing momentum equation, the paper has developed a 3d temperature and flow fields model for mcfc stack based on cfd technique
建立了熔融碳酸鹽燃料電池堆內部單體的暫態溫度模型，並考慮了電堆的輻射換熱、轉換反應、反應氣體組分變化對溫度場的影響；根據mcfc的微分控制方程組，考慮氣體組分的熱力學性質及動量變化的影響，利用數值分析方法求解熔融碳酸鹽燃料電池堆的三維流場與溫度場，分析了各作用因素對熔融碳酸鹽燃料電池堆溫度分佈的影響機制。We calculate the stress fracture limit, critical index limit and melting limit in a high power double clad fiber laser. the results show that the average output power decreases when the temperature is too high. to maintain the pumping efficiency and the output power, some cooling methods should be used when the output power reaches a certain level
給出了熱效應對雙包層光纖激光器影響的裂解極限、臨界折射率極限和熔化極限與光纖結構參數和泵浦功率的表達式，理論分析和數值模擬結果表明對于高功率的雙包層光纖激光器溫度很高時激光增益下降，在一定的功率水平上需要進行外界的冷卻，以保證泵浦激光的效率和高功率的激光輸出。It is found that the effects of the latent heat are not negligible in the laser cladding process and their errors depend on the temperature range during phase transformations and the size of melted material region
計算結果表明，在激光塗敷過程的溫度場分析中，潛熱的影響不是總可以忽略的，其誤差取決于材料在物相轉變時交界面溫差的?圍及材料熔解體積的大小。If the materials are degraded in the event of high temperature and high shearing rate, the melt viscosity will decrease due to the breaking up of the molecular bonds
如果材料因高溫或高剪切率加工而降解，熔膠粘度會因分子鏈斷裂而降低Through the gc analyses and the nuclear magnetic resonance analyses showed that the copolyesters obtained here were random copolymers of 3hb and 3hv units. hv fraction in the copolymers reached 38 %. through thermal analyses showed that the melting point was reduced and pyrolysis temperature was increased
經氣相色譜、核磁共振分析，此共聚物為3hb與3hv所組成的不規則共聚物， hv組分在共聚物中約佔38 ；經熱分析，獲得的phbv共聚物的熔點有所降低，分解溫度有所升高，在性能上優于phb 。The mechanica1 performance is superior to p1ain pp. 0n the sem photographs of impact fracture surface, it was observed that the pu11out of si licate 1ayers hard1y was found and the compat ibi 1 ity of pp and montmori l 1oni te was improved great l y. xrd resu1 ts suggested that the basal spacing of silicate layer was about 4
小角xrd結果顯示，復合材料中無機片層間距d _ （ 001 ）在4 . 0nm左右，為插層型材料，通過dsc測試發現復合材料的熔點和分解溫度均有一定的提高，蒙脫土的加入可提高材料的熱性能。Some main apparent factors involved in the dissolution and deformation process, such as melts composition, atmospheres and temperature etc have been studied, but the reiated details and further experimental evidences in a molectliar ievel are absent and difficult to be obtained at present
（ 2 ）關于nio陰極溶解機理的探討也基本局限在宏觀而間接的研究階段，主要涉及熔鹽組成、氣氛組成和溫度等宏觀影響因素，同樣缺少直接的、分子水平的實驗數據。To avoid degradation, the manufacturing temperature must maintain between 150 - 200 c, it is not suitable for the melting plastics to stay inside the barrel for a long time
避免材料降解，加工溫度須保持150200c ，熔膠不宜停留在炮筒內太久Results showed that temperatures have different effects on the curing speed of resin, the rate of moisture transmission, the degree of plastic melting and the degree of wheat straw decomposition
結果表明，熱壓溫度對板坯中膠黏劑的固化速度、水分傳遞速度、塑料熔融程度、麥秸分解程度等都有不同程度的影響。The thermodynamic conditions of decomposition of the foaming agent tih2, homogeneous and heterogeneous nucleation in high - temperature solid and liquid, growth and movement were achieved to demonstrate the trend of pore evolvement in this paper. moreover, according to the characteristics of in - situ gas foaming, the equations of the height change of foaming samples with heating time were primarily established to study the behavior of foams and to guild the experiment processes
另外，論文通過大量的熱力學分析，得出了發泡過程中發泡劑分解以及氣孔在固液態時的均勻形核和非均勻形核、氣孔的生長和運動等熱力學條件，揭示了氣孔演化的趨勢；論文還根據內生氣源發泡的特點，初步建立了高溫熔體中氣體發泡高度隨時間變化的方程，為進一步深入的研究發泡機理奠定了一定的基礎。分享友人