熔體加入劑 的英文怎麼說
中文拼音 [róngtǐjiārùjì]
熔體加入劑
英文
melted addition-
The results indicated that the dimension, shape and purity of base material could meet the functional demand of solid lubricant ; the thermal decomposition temperature of ptfe resin exceeds 400 c, but organic and inorganic packing filler added in ptfe made the water absorption rate of composite material increased, melting temperature and decomposition temperature decreased, in the meanwhile oxidative decomposition reaction was accompanied ; polar groups such as c = o, c - o - c and so on in the carbon fiber surface is advantageous to increase compatibility with other components and interlayer shearing strength ; uniform design experimental method could help to find the relationship between formula and frictional property by relatively small tests. the developing trend of each formula ' s friction coefficient could be showed by fitting curve ; the friction coefficient with no copper powder or graphite in formula was relatively big. this fact showed that copper powder and graphite should be used cooperatively ; it was found that when the ratio of copper powder to graphite by weight is 15 : 60, 30 : 30 - 40 and 60 : 15 - 30 respectively, the friction coefficient was relatively small. the degree of crystallinity of pure ptfe reached maximum by air cooling and the abrasion loss also reached maximum among three ones ; at the same time, the abrasion loss of solid lubricant sample was also the biggest among three ones ; when solid lubricant matched with 45 # steel axle or gcrl5 steel axle, lubricant transfer film could be formed on metal surface, thus direct contact between the surface of metal friction pair rings was reduced. their working life was elongated extremely ; there was mainly much graphite, a little ptff, moo3, feso4, cus and so on in lubricant transfer film
試驗結果表明：所選原料的尺寸、形狀及純度可滿足固體潤滑劑的性能要求；聚四氟乙烯樹脂熱分解溫度超過400 ，但在ptfe中加入無機填料會使復合材料吸水率提高，熔融溫度及分解溫度降低，且伴有氧化分解反應；碳纖維表面含有c = o及c - o - c等極性基團，有利於提高其與其它組分的相容性，提高層間剪切強度；均勻設計試驗方法能夠用較少的試驗次數找出配方與摩擦性能間的關系，擬合曲線基本能表示各配方的摩擦系數發展趨勢；配方中不加銅粉或不加石墨，其摩擦系數均較高，說明銅粉和石墨應該配合使用；當銅粉15份、石墨60份時，銅粉30份、石墨30 - 40份時，銅粉60 、石墨15 - 30份時，摩擦系數均具有較低值；純聚四氟乙烯樹脂在空氣冷卻時結晶度最大，磨損量也是三者中最大的；同時，固體潤滑劑試樣在空氣冷卻時的磨損量也是三者中最大的：不論是固體潤滑劑與45 #鋼軸配副或是固體潤滑劑鑲嵌入銅套后與gcr15鋼軸配副，在金屬表面均可形成潤滑轉移膜，從而減少金屬摩擦副表面間的直接接觸，大大延長其使用壽命;轉移膜中主要含有較多的石墨、少量聚四氟乙烯、 moo 。Experimental results show that the order of fluoride salt being put in and flux type also influences the phases constitution, morphology, distribution and absorbent rate of ti and b. the experiments on remelting master alloys and al or al alloys at a certain temperature range show that the phases constitution and size have a remarkable heredity
試驗結果表明，不同的氟鹽加入順序和熔劑種類的不同也直接影響著中間合金中化合物的相組成、形態、分佈以及中間合金中ti 、 b的實收率等。在用純鈦顆粒法制備中間合金時，熔煉溫度的改變只能影響tial _ 3晶體的尺寸大小，而無法改變其形態。The results showed that the melting ratio of silica flux decreases and the complete melting time prolongs with the size of silica flux and matte grade increasing, and the effect of the blowing air and oxygen enrichment is not remarkable in the high grade copper matte converting process
對于高品位冰銅轉爐吹煉，鼓入氣體流量和氧濃度對石英熔劑熔化率影響不顯著；熔劑粒度和冰銅品位對熔化率影響顯著，並隨著熔劑粒度和冰銅品位的增加，熔劑熔化率降低，完全熔化時間延長。In this paper the formula, the technics, the dosage of the filler and the macromolecule coupling agent are studied which influence the technics condition, mechanical properties, structure configuration. also x - ray large angle diffraction, scan electron microscope, dta etc are used to analysis and test the properties of the pp / talc composites. conclusions as follows : 1
本文系統地研究了復合體系配方、工藝方法、填料及偶聯劑用量對復合體系工藝條件、力學性能及結構形態的影響，同時利用廣角x射線衍射、掃描電鏡、 dta等對復合體系的性能進行了測試與分析，主要研究內容及結論如下： 1滑石粉的加入，雖然使pp的熔化時間增加，但是混煉能耗下降，有利於pp的加工；偶聯劑的加入，使pp的熔化時間增加，能耗略有降低，總體而言，對加工無不利影響。The result of experiment showed that the reaction between ti and c is a thermodynamic course, when 2 wt % mg is added to melt, it can restrain the formation of fragility phase al3ti, and gained al matrix composite which contained tic reinforced particles only. because mg reacts with the forms a micro - high temperature field around the oxide around the graphite particles and the oxygen gas which is brought by the immersion bell, and the reaction gives out a lot of heat energy, thus forms many high micro - fields in melt, which prompt the reaction between the al and ti
加入適量的mg （ 2wt ）可以抑制tic al復合材料中的脆性相al _ 3ti的產生，生成僅含tic的鋁基復合材料；由於活化劑鎂在體系中與石墨顆粒周圍的氧化物、以及外來的氧反應放熱，在熔體中形成微高溫區，促進al - ti反應，同時， al - ti反應也是放熱反應，因此體系中的內能急劇增大，促使al _ 3ti分解以及ti朝c顆粒擴散，縮短反應的孕育時間。分享友人