熱偏差系數 的英文怎麼說

中文拼音 [rèpiānchāxìshǔ]
熱偏差系數 英文
coefficient of thermal deflection
  • 偏 : Ⅰ形容詞1 （不正; 歪斜） inclined to one side; slanting; leaning 2 （只側重一面） partial; prejudi...
  • 差 : 差Ⅰ名詞1 （不相同; 不相合） difference; dissimilarity 2 （差錯） mistake 3 [數學] （差數） differ...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. That means the controlled temperature al1ow waving in a range in a period. when the change of the temperature indoor is out of the range we enacted, the system begin to regulatc. compensate the windage last time leave behind } before decide the heatsupply parameter for the next time

    即允許被控室內溫度在一段時間內存在一定幅度的波動，當室溫變化幅度超過設定值時系統開始調節，在確定下一時間段的供熱參數之前對上一時間段的遺留偏差在短時間內給予補償。
  2. The vary of the parameter of the steam ). the software provide function of " alert " if some parameters exceed the range of permission, and this may urge the operator to adjust operation condition and put right. meanwhile, this may promise the units under the conditions of optimization, and achieve lower net coal consumption rate of thermal power plant and higher generation efficiency

    同時，這套系統可以在線分析熱力系統的各小指標如主蒸汽參數、抽汽參數和排汽參數在偏離目標值時所引起的煤耗額外增加值，對于偏離目標值超過允許范圍時的參數提出報警，以提醒運行人員調整運行，糾正偏差，使各參數都運行在最佳狀態，從而降低煤耗，提高機組的運行效率。
  3. At the initial stage of planar technique, b was employed as ideal diffusion impurity in base - region of npn si planar devices because of the match of its solid - solubility and diffusion coefficient in si with those of p in emission - region, and the good shield effect of sio2 film to b. but because of the relatively large solubility ( 5 1020 / cm3 at 1000 ) and the small diffusion coefficient, the linear slowly - changed distribution of acceptor b in pn junction can not be formed, which could not cater to the requirement of high - reversal - voltage devics. thereafter b - a1 paste - layer diffusion technology and close - tube ga - diffusion technology had been developed, while the former can lead to relatively large the base - region deviation and abruptly varied region in si, which caused severe decentralization of current amplification parameter, bad thermal stability and high tr ; the latter needed the relatively difficult pack technique, with poor repeatability, high rejection ratio, and poor diffusion quality and productio n efficiency

    在平面工藝初期，由於b在硅中的固溶度、擴散系數與n型發射區的磷相匹配， sio _ 2對其又有良好的掩蔽作用，早被選為npn硅平面器件的理想基區擴散源，但b在硅中的固溶度大（ 1000時達到5 10 ~ （ 20 ） ，擴散系數小， b在硅中的雜質分佈不易形成pn結中雜質的線性緩變分佈，導致器件不能滿足高反壓的要求，隨之又出現了硼鋁塗層擴散工藝和閉管擴鎵工藝，前者會引起較大的基區偏差，雜質在硅內存在突變區域，導致放大系數分散嚴重，下降時間t _ f值較高，熱穩定性差；後者需要難度較大的真空封管技術，工藝重復性差，報廢率高，在擴散質量、生產效率諸方面均不能令人滿意。
  4. The numerical simulation result obtained by taking the dimensionless mass transfer coefficient as the input parameter of the mathematical model is consistent with the 73 groups of the experimental data and the discrepancies of the enthalpy efficiency and regenerative efficiency are mainly within 15 %

    以實驗得到的量綱一傳質系數作為數學模型的輸入條件，數值計算結果與73組實驗數據吻合很好，全熱效率和再生效率的偏差均集中在15 %以內。
  5. Structure sizes of superheater tubes and inside resistance coefficients as well as imbalance thermal loads will result in thermal deviation

    過熱器管子結構尺寸、內部阻力系數及熱負荷不均勻，將會產生熱偏差。
  6. Analytical relationships are obtained for calculation of the coefficient of heat transfer for condensation in tube, the relative difference between the experimental value and the calculated value is smaller than + 15 %

    關聯出了相應的水平管內冷凝傳熱膜系數的計算式，計算值與實測值的偏差在15以內。
分享友人
分享到 Line

分享到臉書