熱力彈性 的英文怎麼說
中文拼音 [rèlìdànxìng]
熱力彈性
英文
thermo-elasticity-
1, reasonable sructure, good elasticity, large range of compensation pipeline and little counterforce to the brackets of pipeline
1結構合理，彈性好，補償管道熱脹冷縮范圍大，對管道支架的反作用力小It provides strong basement for the research of design. the method of structure analysis commended by this paper is based on nonlinear finite - element, diathermanous and elasticity mechanics. it found the model of a steel beam pressed by gravity and temperature in the condition of indoor fire
本文提出的結構分析法是在大量參數分析的基礎上，以非線性有限元、傳熱學及彈性力學為基礎，利用ansys軟體，建立一個鋼框架梁在室內局部火災條件下的傳熱模型與在重力荷載及溫度荷載共同作用下的受力模型。The plane thermoelastic fields for elliptical inhomogeneity problem are studied
研究了彈性橢圓夾雜體的平面熱力耦合問題。The temperature effect which has been calculated is taken as " thermal load " forced on the body, then such thermal stress is settled as general elasticity mechanics question ; secondly, the thermal stress is taken as " surface force " forced on the body, and the new system stiffness is formed which include the extra stiffness matrix, then it changes the nature frequency of the structure
首先，這篇論文介紹溫度場和熱應力場的有限元方法，建立了三維熱傳導模型計算有溫度場產生的熱應力，計算熱應力時運用了一種轉化思維：將溫度處理為「溫度載荷」 ，這樣就能用彈性力學問題的處理方法來求解熱應力。其次，將熱應力作為結構的「面內力」 ，而面內力產生附加的幾何剛度矩陣，改變了結構的剛度，影響了結構的固有頻率。Secondly, based on the syntony frequency and the elasticity mechanics and other correlative professional knowledge, establishes a suit of fsm vibration module system, selects the structure, material and the process and treatment technique of the elastic element in the elastic system of the mirror, analyzes a lot of factors which affect the structure of the rapid controlling reflector and provides the derivation formula
以諧振頻率為出發點，利用彈性力學等相關專業知識，建立一套fsm的振動模塊系統；確立了反射鏡彈性系統中彈性元件的結構、材料的選擇，及加工，熱處理。分析了影響快速控制反射鏡結構的諸多因素，給出其相關推導公式，最後應用solidedge和cosmos軟體對該結構進行了計算機模擬。In the paper, not only such factors as reinforcing steel bar, various placing temperature of concrete in case of lift placements, lift thickness, time interval between lifts, the variation of elastic modules of concrete, heat of hydration, the temperature changes of environment but the effect of creep deformation and autogenous volume change on the temperature field and thermal stress field of reinforced concrete face - slab are considered
本論文在分析中，考慮了鋼筋、混凝土分層澆築、入倉溫度、澆築層厚、施工間歇、混凝土彈性模量變化、水化熱發散規律、外界氣溫等因素的變化及混凝土徐變和自生體積變形等因素對面板溫度場和溫度應力的影響。In this article, according to heat conduction theory, elastic creep theory and finite element theory, the temperature field and creep stress field in the arch dam during construction and operation are simulated and analyzed by means of three dimensional finite element relocating mesh method, and the distribution law of the temperature field and creep stress field in the arch dam during construction and operation are systematically studied, and according to the construction process of concrete arch dam, the effect of lamination placement, construction interval, elastic modulus change, thermal insulation change, surrounding temperature change, concrete creep and autogenous volume change on thermal stress in the arch dam are also considered
論文根據熱傳導理論、彈性徐變理論及有限元理論，用三維有限元浮動網格法對拱壩施工期和運行期溫度場、徐變應力場進行了全過程模擬分析，較為系統的研究了混凝土拱壩施工期和運行期溫度場、徐變應力場的分佈規律，在分析中按照混凝土拱壩施工過程，考慮了混凝土分層澆築、施工間隙時間、彈模變化、絕熱溫升過程、環境溫度的變化、混凝土徐變、自生體積變形等因素對壩體溫度應力的影響。In computation the effect of thermal insulation, elastic modulus, creep degree and autogenous volume change along with age, the progress of pouring by layer, work suspension in summer, the change of air temperature, heat preservation, water cooling, and water storage, by stages on temperature field are considered
計算中考慮了混凝土的絕熱溫升、彈性模量、徐變度和自生體積變形隨齡期的變化以及分層澆築、夏季停工、外界氣溫變化、表面保溫、通水冷卻及分期蓄水等因素對壩體溫度應力場的影響。This paper establishes a model simulating dam actual placing process and considering the non - continuity of initial temperature on the boundary of new and old concrete, daily air temperature change, concrete - placing temperature, hydration heat, heat insulation on boundary, water - storing process, placing intermission and curing with water. the calculation of stress field considers the concrete weight, static water pressure, thermal stress, different autogenous volume change between rcc and normal concrete, change of elastic modulus of concrete with age and creep action
考慮了乞今最為全面的初始條件和邊界條件，包括模擬壩體的實際升程過程，考慮了新老混凝土接觸面上的初始溫度不連續，逐日的氣溫變化，混凝土的入倉溫度，水化熱溫升，邊界保溫，水庫蓄水過程，澆築間歇以及灑水養生等因素；應力場的計算考慮了混凝土的自重，靜水壓力，溫度應力，常態混凝土與碾壓混凝土不同的自生體積變形，混凝土的彈性模量隨齡期的變化以及徐變的作用。From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program
針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。Because the propellant grain is viscoelastic material, the liner and adiabatic layer are also viscoelastic one, the interface debond problem is actually interface crack about elastic - viscoelastic or bi - viscoelastic materials. research about this problem relates to the knowledge of viscoelastic mechanics and interface fracture and combustion. numerical analysis method about interface debond on solid rocket motor is researched in this paper
由於固體火箭發動機的推進劑藥柱是一種粘彈性材料，襯層和絕熱層也具有粘彈性性質，因此其界面脫粘問題實際上是彈性-粘彈性或雙粘彈性各向同性材料界面裂紋問題，對該問題的研究涉及到粘彈性力學、界面斷裂力學和燃燒學等相關學科。This paper also researches on thermal elastoplastic analysis model of multilayered graded coating structures on the basis of thermal elastoplastic analysis model of trilayered materials with the focus on the structural character of graded coating. it builds the thermal elastoplastic analysis theory for the graded coating structure that has a single plastic layer or two plastic layers. it gives the analytical formulas of thermal stresses and the thermal elastic - plastic transform temperatures of graded coating that has a single plastic layer or two layers under the thermal loading
針對梯度塗層的結構特徵，在建立的三層疊層材料熱彈塑性分析模型的基礎上，對多層梯度塗層結構的熱彈塑性分析模型進行了研究，分別建立了含單個塑性層和兩個塑性層的梯度塗層結構的熱彈塑性分析理論，給出了在熱載荷作用下含單個塑性層和兩個塑性層的梯度塗層的熱彈性-塑性臨界溫度和熱應力分析公式，利用有限元分析對理論模型進行了驗證。Based on the relaxation constitutive theory of viscosity - elasticity under non - constant temperature, the equation of thermal conduction in solids, and the finite element method, the non - stationary thermal stress in low carbon steel thick hollow sphere is calculated
摘要基於變溫粘彈性鬆弛型本構理論、熱傳導方程和有限元方法，對低破鋼厚壁球的非定常熱應力進行了分析。Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application
熱、壓環境下壓阻變換壓力傳感器的性能可以通過有限元方法預測.這里研究了簡化的1 / 8模型，模型考慮了二氧化硅和氮化硅生成過程及堆陽極鍵合和膠粘結合過程.結果發現有限元預測結果和實驗數據具有可比性.範例研究表明，硼硅堆導致產生一定的非線性，但它隔離了硬環氧樹脂的非線性.在包裝過程中最好使用柔性環氧黏合或軟黏膠性結合.黏合材料的黏彈性和黏塑性將會導致傳感器輸出的滯后和漂移誤差.然而，在相對穩定的環境下，軟黏合劑對傳感器的影響可以忽略.此外，詳細的設計和過程信息有助於提高模型的適用性In order to search the demolishing effect pf the thermal stress on the hearth and bottom of the blast furnace, the distribution of temperature field and the thermal stress have been studied with the thermal elastic law and finite element method
摘要為了探討熱應力對不同材質構成的高爐爐缸磚襯的破壞作用，在計算溫度場的基礎上，應用熱彈性理論和有限元法對高爐爐缸進行應力分佈計算。Plastics piping systems. elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping. test method for leaktightness under external hydrostatic pressure
塑料管道系統.熱塑塑料壓力管道用的彈性密封環型接頭和機械接頭.外部液壓條件下防漏密封試驗方法Plastics piping systems - elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - test method for leaktightness under external hydrostatic pressure
塑料管道系統.熱塑塑料壓力管道用的彈性密封環型接頭和機械接頭.外部流體靜壓條件下防漏密封試驗方法Calculation for thermal stresses of asphalt pavement under environmental conditions based on thermalviscoelasticity theory
環境條件下瀝青路面熱粘彈性溫度應力計算Standard practice for stress relaxation testing of raw rubber, unvulcanized rubber compounds, and thermoplastic elastomers
生橡膠非硫化橡膠和熱塑彈性物的應力釋放試驗用標準實施規程Starting with causing mechanism of magnetostriction, this paper analyses and discusses the relationship of physical properties of magnetic crystal, deduces thermodynamics equation of the properties of magnetic crystal, such as magnetism, thermal and elasticity
本論文從磁致伸縮現象的產生機理入手，對磁性晶體物理性質之間的關系進行分析和論述，並根據熱力學理論，給出了磁性晶體的磁、熱和彈性性質的熱力學方程。分享友人