熱加工的 的英文怎麼說

中文拼音 [rèjiāgōngde]
熱加工的 英文
hot worked
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 的 : 4次方是 The fourth power of 2 is direction
  1. And then, metal structure with aspect ratio 30 was obtained in our laboratory. eventually, a few micro parts with high aspect ratio were fabricated by liga process under the optimum condition. there were key parts of micro thruster, netlike nickel antielectron modulator, micro copper radiator, stainless steel micro components and many filter mediums with different shapes and dimensions

    最後，我們利用liga技術加工的獨特優點，以發展其高深寬比技術的實際應用，先後製作了狹縫陣列鎳結構微推進器關鍵部件、薄壁網狀多孔鎳結構正電子慢化體、微型銅結構換熱氣和多種材料不同、尺寸各異的過濾介質，還結合利用liga技術和微細電火花技術的加工優點，製作出了不銹鋼微結構
  2. Forging hammer is an important device, which is used to forge roughcast in machine shops. when forging hammer works, violent vibration produces, so the precise instruments and equipment around ca n ' t run normally, the stability and longevity of the workshop structure may lower, furthermore, the health of people hurts. the damping to forging hammer foundation is all through the ages a hot question for discussion

    鍛錘是機械工廠中一種對毛坯進行鍛造加工的重要設備，但鍛錘工作時產生的極大振動，不僅嚴重影響周圍精密儀器、設備正常運行，降低廠房建築結構的穩定性及其使用壽命，而且是一種危害人體健康的工業公害，因而鍛錘隔振歷來是一個熱門研究課題。
  3. Research on continuous cooling transformation and microstructure of x70 acicular ferrite pipeline steel

    控制熱加工下管線鋼中針狀鐵素體的形成
  4. Thus atom diffusion is a ' key factor to pecht. how do atoms diffuse under bpec heating

    因此，原子的擴散是決定脈沖大電流熱加工的重要因素。
  5. And is it the same as under radiation heating ? do the special electric and magnetic fields produced by bpec accelerate atom diffusion ? understanding the above questions fully is a key to expose the mechanism of pecht

    在脈沖大電流加工過程中原子是如何擴散的，與一般的加熱燒結、焊接是否一樣，脈沖大電流形成的特殊電場及磁場是否對原子的擴散有大的推動作用，弄清這些問題成為進一步揭示脈沖大電流熱加工機理的關鍵。
  6. In this paper, three unique models were designed to research atom diffusion at interface, contacting line and joining point under bpec heating and compare with it under radiation heating in order to find out if bpec speed atom diffusion. the first model was aimed to research atom diffusion at interface under bpec heating. experiment condition of bpec diffusion welding sheet cu and ni : direct diffusion welding, at a pressure of l0mpa, welded at 750 ~ 900, with heat rate of 200 ~ 400 / min for 10mm, on / off of 6 / l ~ 48 / 8, with die or not, vacuum of 6pa

    本文設計出三種樣品預構件，研究脈沖大電流加熱條件下片狀材料、線狀材料和球形顆粒之間的原子擴散過程，弄清脈沖大電流加熱條件下原子擴散與一般燒結和焊接過程中原子擴散的區別，以證實特殊的電場和磁場是否對原子的擴散有推動作用，揭示脈沖大電流加熱條件下原子的擴散過程，探索脈沖大電流熱加工技術快速高效的原因。
  7. Pulse electric current heat treatment ( pecht ) developed by sodick, ltd., of japan, is a recently developed material processing method which consists of spark plasma sintering and welding, plasma activated sintering and welding, big pulse electric current ( bpec ) diffusion welding etc. the following are basic merits of pecht : rapid heating and cooling ; short sintering or welding time ; lowering sintering or welding temperature

    脈沖電流熱加工（ pulseelectriccurrentheattreatment ，比如燒結，焊接等）是九十年代發展起來的一種材料快速制備新技術，它包括放電等離子燒結與焊接、等離子活化燒結與焊接、脈沖大電流擴散焊接等。它具有升溫、降溫速度快、能在較低的溫度下燒結或焊接以及時間短的特點。
  8. A sil flying head is designed to keep the distance between sil and recording medium in near - field range. a sil optical data storage system is built up when the recording head is combined with sil flying head. meanwhile, using astigmatic focusing error detection technology and twin optical pick - up heads, a novel nontouching nanometer measurement method is developed to measure the flying height of sil, and provides us with a powerful tool to optimize the design of sil fly head

    在sil存儲技術研究方面，首先提出一種光學玻璃熱熔加工製作sil的新方法，該方法克服了小半徑球透鏡加工的難題，成功製作出了半球固體浸沒透鏡；設計了sil飛行頭系統，並利用光學頭像散法聚焦誤差檢測原理，設計出一種雙光學頭sil飛行高度測量方案，實現了sil飛行頭飛行高度的測量。
  9. Shiyou obtain the sanitation registration for exporting products of cloven - hoofed animal and poultry to japan in jan. 1995

    公司在1995年1月取得了對日出口熱加工偶蹄類、禽類產品的衛生注冊。
  10. The thermoelectric power outputs of laminated structures with various thermoelectric materials have been mathematically optimized and experimentally measured. some conclusions have been drawn in the present work as follows : 1. the performance, microstructures and the failure mechanism of laminated bi2te3 / fesi2 prepared by dip coating using tin - based alloys as bridge materials have been investigated

    本項研究獲得了以下主要成果： 1 、以sn基合金為焊接材料，採用熱浸焊技術制備了bi _ 2te _ 3 / fesi _ 2疊層熱電材料，並系統地分析研究了疊層熱電材料的性能，焊接過渡層的微觀組織結構以及過渡層在熱加工及模擬服役過程中的破壞機制。
  11. The structural evolution of alloy gh720li ingots during hot working

    合金鑄錠熱加工過程中的組織演變行為
  12. As a matter of fact, pecht is achieved by atom diffusing

    實際上，脈沖大電流熱加工過程是由原子的擴散過程來實現的。
  13. Standard specification for steel tie plates, low - carbon and high - carbon hot - worked

    熱加工的低碳鋼和高碳鋼墊板的標準規范
  14. Standard practice for preservative treatment of utility poles by the thermal process

    熱加工的多用電桿的防腐處理標準實施規程
  15. Industrial thermoprocessing equipment - safety requirements for the generation and use of atmosphere gases

    工業熱加工設備.環境氣體產生和使用的安全要求
  16. Our factory produces various kinds of cnc automatic lathe tool, rubs and makes boring, the nonstandard cutter, the professional manufacturers of hard alloy serial cutters completely

    本廠是生產各種cnc自動車刀、全磨製鉆、非標刀具、硬質合金系列刀具的專業生產商，提供高工鋼材料，配備熱加工處理及檢驗。
  17. The purpose of the paper is to search the feasibility of the ecletron - beam weld of ti3al intermetallics and tc11 ( a + b ) two phase titanium alloy, and the influence to weld microstructure and properties of the hot deform and heat treatments

    本文的目的是探索ti _ 3al金屬化合物tac - 1b合金與tc11兩相鈦合金電子束焊、熱模鍛及熱處理的可行性，並研究焊后熱加工變形與熱處理對組織與性能的影響。
  18. By vacuum - electron - beam weld of ti3al and tc11 the technology of hot die forging, and then use different heat treatments, study the influence law of the different degree of deform, different heat treatments to the microstructure and properties

    採用熱模鍛技術，通過對tac - 1b 、 tc11進行不同程度的變形、真空電子束焊接，然後採用不同的熱處理工藝，研究熱加工工藝對合金組織，性能的影響規律。
  19. Steel for the prestressing of concrete - part 5 : hot - rolled steel bars with or without subsequent processing

    混凝土預應力鋼筋.第5部分:有或無后續加工的熱軋鋼筋
  20. The data of mechanical properties test proved that the composite materials compounded with 0. 39 ~ 0. 46um ps organic rigid particles at 0. 2 % ( wt ) and pp have excellent strength and toughness. sem photograph found that the organic rigid particles were separated into 60 ~ 80nm size in the composite by melting process, which has belter toughness compare with the pp compounded with ultra - fine organic rigid particles

    用2粒徑為0 . 39 0 . 46um的xps復合pp ，經力學性能測試，有最好的增韌效果； sem掃描電鏡發現，經熱加工的復合材料中最小的有機剛性粒子粒徑可部分分散到60 80nm ，該復合材料比超細有機剛性粒子復合的pp有更好的沖擊韌性。
分享友人
分享到 Line

分享到臉書