熱塑流 的英文怎麼說
中文拼音 [rèsùliú]
熱塑流
英文
thermoplastic flow-
Mfr plastics - determination of the melt mass - flow rate and the melt volume - flow rate of thermoplastics
塑料.熱塑性塑料熔體質量熔流流速08. 01 flow rate of thermoplastics by extrusion plastometer, test method for
擠壓式塑性計測試熱塑性塑料流速的方法Standard test method for melt flow rates of thermoplastics by extrusion plastometer
使用擠壓式塑性計測定熱塑塑料的熔融流量率的標準試驗方法Thermoplastics piping systems. non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings. test method for leakightness under internal hydrostatic pressure without end thrust
熱塑料管道系統.壓力管和模塑配件的合成橡膠密封環型接合.在無軸向推力時內部流體靜力學壓力下密封性試驗方法08. 03 test method for flow rates for poly vinyl chloride and rheologically unstable thermoplastics
聚氯乙烯及流變的不穩定熱塑物質流動速率測試方法Plastics piping systems - elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping - test method for leaktightness under external hydrostatic pressure
塑料管道系統.熱塑塑料壓力管道用的彈性密封環型接頭和機械接頭.外部流體靜壓條件下防漏密封試驗方法Practice for underground installation of thermoplastic pipe for sewers and other gravity - flow applications
排污水和其它重力流動設備用熱塑性管的地下安裝實施規程The flow stress model of 35crmo structural steel during hot forming
結構鋼熱塑性變形流動應力模型Thermoplastics pipes, fittings and assemblies for the conveyance of fluids - determination of the resistance to internal pressure - part 2 : preparation of pipe test pieces
流體傳輸用熱塑管接頭和組件.抗內壓力的測定.第2部分:管試件的準備An experimental apparatus has been set up start from scratch and some experiments have been done to study the heat transfer characteristics of the ice - on - coil tank. the comparison of the theoretical predictions and the experimental data has been made and the disagreements between them are also analyzed
建立了導熱塑料蓄冰盤管傳熱性能測試裝置,測試了結冰和融冰過程中載冷劑的進出口溫度、流速和結冰或融冰時間的關系,通過實驗結果與理論計算的比較和誤差分析,驗證了建立的數學模型的合理性。Standard test method for flow rates for poly vinyl chloride with molecular structural implications
聚氯乙烯和流變的不穩定熱塑性材料流動速率的測試試驗方法A comparison between traditional rubber and tpe on the production flow more on technical and factual data
傳統橡膠及熱塑性彈性體tpe在生產流程上的比較In numerical control, data concerning all aspects of the machining operation, such as locations, speeds, feeds, and cutting fluids, are stored on magnetic tape, cassette, floppy or hard disks, or paper or plastic ( a thermoplastic polyester )
在數控中,關于機床控制所有方面的數據,例如位置、速度、流動、流體分流、存儲在磁帶,軟盤或硬盤,或者是紙,或者是塑料(一種熱塑性的聚酯) 。3. do not be recommended without a single hot plate hot nozzles injection plastic
3 .建議不要應用於不帶熱分流板的單熱噴嘴注塑。Determination of the melt mass - flow rate and the melt volume - flow rate of thermoplastics
熱塑性塑料熔體質量流動速率和熔體體積流動速率的測定When cable used circumstance can prevent thermoplastic flow and admit reduce insulated resistance, if shorten working hours, pvc insulated and nylon jacketed wires and cables ' operating temperature can increase to 105 s which can continuous operating temperature 90
當電纜使用環境可防止熱塑流動和容許減小絕緣電阻的情況下,能連續90使用的pvc絕緣尼龍護套線,在縮短總工作時間的前提下,其工作溫度可提高至105 。Thermoplastics piping systems - non - end - load - bearing elastomeric sealing ring type joints between pressure pipes and moulded fittings - test method for leaktightness under internal hydrostatic pressure without end thrust
熱塑管道系統.壓力管和模塑管件的無端負荷彈性密封環型連接件.在無軸向推力時內部流體靜壓力下密封性的試驗方法Gas shut - offs and valves in gas distribution systems, manually operated thermoplastic
氣體分配系統中手動熱塑氣體截流閥及閥門Manually operated thermoplastic gas shutoffs and valves in gas distribution systems
氣體分配系統中的手動熱塑性氣體截流閥及閥門Thermoplastics pipes for the transport of fluids - determination of impact by the charpy method
流體輸送用熱塑性塑料管材簡支梁沖擊試驗方法分享友人