熱座模式 的英文怎麼說
中文拼音 [rèzuòmóshì]
熱座模式
英文
hotseat-
There will be the hotseat mode and several multiplayer modes
將會有「熱座」模式和幾種聯機對戰模式。The algorithm of strapdown inertial navigation system is also discussed and then use the flight - track generator to give a simulation, since a closed loop feedback integrated navigation system is designed in this paper, and the output of the filter must feed back to the strapdown inertial navigation system, the analysis of the algorithm in strapdown inertial navigation system is important. the scheme to design the trajectory of gps and the simulation of gps constellation are then studied, the simulation of gps constellation is given from the calculation of vernal equinox base on the principle of celestial mechanics, this method of different from other methods given by other paper and is useful to the research of satellite navigation system. a new method to abstract noise modal in integrated navigation system is proved to be useful in practice, this method, which is given by use the principles of stochastic processes, statistics, time series analysis, and system identification, is suitable for the kalman filter in integrated navigation system
如航跡產生器的設計，該航跡產生器是研究組合導航問題的前提，從國外一些研究組合導航系統的文獻中可以看出，設計這樣一個航跡產生器是非常必要的，所以本文自行設計了這樣一個系統；還討論了捷聯慣性導航系統中捷聯解算的方法，並進行了模擬研究，由於在本文設計的閉環反饋式組合導航系統中，對捷聯慣導系統的平臺誤差進行閉環控制，需要將濾波器輸出的校正量反饋到捷聯解算內部，所以必須對捷聯解算進行深入的研究和分析，更何況捷聯解算問題本身也是導航界的一個熱門研究課題；另外，本文還介紹了gps軌道及其星座模擬的設計思想和方案，與以往gps軌道和星座模擬不同的是本文從天體力學中計算春分點開始，逐步進行gps軌道及其星座模擬，這樣的設計方法對從事衛星導航的研究工作是有價值的；還對組合導航中誤差建模方法進行了研究，綜合運用隨機過程、概率統計、時序分析及系統辯識等方面的理論提出了一套適合組合導航卡爾曼濾波的誤差建模方法，並運用實際研究工作中的測量數據對該方法進行了驗證。Pangan hot strip mill is a large plants for hot steel coil, it ’ s mainline automatic system is two levels, the level 1 is basic automatic control system, and level 2 is process control system, level 2 controls the furnace area 、 rough mill area and finish mill area, it ’ s main function is data traffic 、 steel rolling tracing 、 the model calculating for setup and the sampling for the rolling data. the process system will save a mass of data for model data 、 setup data and sampling data
攀鋼熱軋板廠是一座大型的熱連軋鋼板生產工廠，主軋線自動化系統採用2級控制結構，其中第1級是基礎自動化控制系統，第2級是過程式控制制系統，主要完成從加熱爐區、粗軋區、精軋卷取區的數據通信、軋件跟蹤、加熱和軋制模型參數設定計算以及軋制過程參數的採集等主要功能。At night, when the heat load is much lower, the chiller operation will be switched to the night mode. the by - pass valve linking the two groups of chillers will be opened so that one group of chiller can provide sufficient chilled water and thus cool air for the whole building
在夜間，熱力負荷大大降低，製冷機改以夜間模式運作，兩組製冷機之間的分流活門會打開，使用一組製冷機已可提供足夠的冷水和冷氣給整座大廈。分享友人