熱模鍛造 的英文怎麼說

中文拼音 [rèmóduànzào]
熱模鍛造 英文
hot die forming
  • 模 : 模名詞1. （模子） mould; pattern; matrix 2. （姓氏） a surname
  • 鍛 : 動詞（把金屬加熱后捶打; 鍛造） forge
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 鍛造 : forge; forging; smith forging; smithing; hammering; blacksmithing
  1. 3d coupled thermo - mechanical fem simulation of forging process of tc4 alloy workpiece

    4鈦合金鍛件鍛造過程三維熱力耦合有限元模擬
  2. What ' s more, the application of tc11 two phase alloys to the compress disk of areoengine alredy is relatively mature, and tc11 alloy may work safely for very long time below 500 c. ti3al matrix alloy and ( a + b ) two phase alloy is connected by weld. the request of the temperature and stress can be satisfied by dual alloy disk with isothermal forged ( or hot die forging )

    選用ti _ 3al基合金tac - 1b和tc11兩相鈦合金用焊接工藝連接起來，通過熱模鍛或等溫鍛鍛造和不同的變形熱處理制度，製造出雙合金盤可以滿足溫度、應力對盤件的要求。
  3. The 60mn hot die forging hydraulic press, with weight 30 % reduction of the main body compared with the traditional hydraulic press because of plate frame structure designed through new idea by adopting transverse pre - tightening technology mainly embodying the design and manufacturing level of the heavy - duty hydraulic presses at modem times, the first one with independent intellectual property right designed by china itself and a transverse pre - tightening plate - frame hydraulic press with max. tonnage in the world at present

    摘要60mn熱模鍛液壓機，採用橫向預緊技術，創新設計了板框式本體結構，與傳統液壓機相比，機械本體重量減少了30 % ，採用的主要技術集中體現了當代大型液壓機設計和製造技術水平，成為中國自行研製的具有自主知識產權的首臺，並且也是目前世界上最大噸位的橫向預緊板框式液壓機。
  4. The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine

    實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。
  5. With improvement of material composition and processing, the failure modes demonstrate predominately elevated wear and plastic deformation, and no earlier failure occurred, leading to a considerable improvement of service life and a stable number of 6000 ~ 7000 times, 80 % more than forging steel dies

    經改進材質及工藝后，熱磨損、塑性變形為主要失效形式，而未出現早期斷裂失效，壽命得到明顯提高，穩定在6000 ~ 7000件，高於鍛造模具鋼80 %以上。
  6. The company is a sino - foreign joint - venture enterprise, incorporating smelting, electroslog, refining, forging, steel rolling and tool manufacturing. it has production lines for high speed steel, mould steel, hss circular saw blades, face - sides cutters, mould, blocks, pre - hard fine plate, garden knives, alloy special cutters and planer knives, as well as six production lines for heat treating. the nano coating center is production base for tool & mould steel productions in domestic

    公司是一家集冶煉、電渣重熔、鍛造、軋鋼、精整、工具製造於一體的中外合資企業，擁有高速鋼、冷、熱作模具鋼生產線，高速鋼圓鋸片、三面刃銑刀、模具預硬精板、木工刨刀生產線，高溫熱處理、表面鍍層研發加工中心，是國內最專業的工模具鋼製品化生產基地。
  7. Taking the radial forging process of the rd2 axle for example, the characteristics of the forging heating and forging craft and radial process in sliding method have been analysed with establishing the sliding field code and doing a speed diagram of the radial forging deformed process

    摘要以rd2車軸徑向鍛造為例，分析了其鍛造加熱及鍛造工藝的特點，並且用滑移法分析徑向鍛造變形過程，建立了外摩擦影響下的滑移場模式，並做出了與之相對應的速端圖。
  8. Nakano forging employs a sub press to carry out stamp forging of brass materials, which have superb hot - forging forming characteristics and can be punched in both the horizontal and vertical directions using the horizontal method and the closed die method

    熱鍛造成型性優越的黃銅材料在模型鍛造時可通過模架模實現水平及垂直方向進行鉆孔水平式，合模式，可滿足顧客省材，省切割加工的需要，特別是數量越多其特點越明顯。
  9. The multi - stage forging process of a gas turbine compressor blade is simulated using 3d coupled thermal - mechanical rigid - viscoplastic finite element method

    摘要利用熱力耦合剛塑性有限元法，對某重型燃機葉片的多工步鍛造過程進行了數值模擬研究。
  10. As a result, the metal flow pattern during forging process is analyzed and distributions of some thermomechanical field variables such as temperature 、 stress and strain are obtained, through which the forming laws during forging process of a gas turbine compressor blade are revealed

    通過有限元數值模擬，分析了鍛造過程中的金屬流線分佈，得到了溫度場、應力應變場等熱力參數的場量分佈，從而揭示了葉片鍛造的變形機理。
  11. Abstract : this thesis introduces the structure, qualities, technical parameters, design bases, and application of the newtype continuousdie - forging gasheater for the medium and small sized blowout patch blank

    文摘:介紹中小型軸圈坯料鍛造用天然氣新型連續模鍛加熱爐的結構、特點、技術參數、設計依據及使用效果。
  12. Column setup : die & mould technology overview ; cad / cam ; stamping die technology ; cavity die ( plastic die, die casting die, forging die, rubber model die, etc. ) technology ; die making technology ; die material and heat treatment technology ; business operation and management ; business information ; die & mould technology both here and abroad and lecture, etc

    主要欄目設置：模具技術綜述、模具cad / cam 、沖模技術、型腔模（塑料模、壓鑄模、鍛模、橡膠模等）技術、模具製造技術、模具材料及熱處理技術、企業經營管理、行業信息、國內外模具技術及講座等等。
  13. Many means such as reasonable selecting mould material, correct forging process, appropriate heat treatment, rough machining of type hole before quenching and so on are taken in production to prevent deformation and cracking of mould effectively

    在生產實踐中，通過合理選擇模具材料、正確的鍛造工藝、合適的熱處理工藝以及淬火前形孔預加工等措施，可有效防止模具的變形與開裂。
分享友人
分享到 Line

分享到臉書