熱破裂強度 的英文怎麼說
中文拼音 [rèpòlièqiángdù]
熱破裂強度
英文
hot rupture strength-
Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )
本研究以武裝直升飛機防護裝甲材料為研究對象，採用真空熱壓粉末冶金燒結工藝制備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料，結合其力學性能、掃描電鏡和界面微區能譜分析結果，分析了sic _ p al復合材料的真空燒結過程中的界面現象，以及材料增強和斷裂機理，並利用hopkinson高速壓桿沖擊實驗系統對其從靜態到動態（應變率為3 . 3 10 ~ （ - 3 ） s ~ （ - 1 ） 5 . 2 10 ~ 3s ~ （ - 1 ） ）的壓縮破壞響應進行了研究，分析了不同體積分數sic _ p al復合材料高應變率壓縮載荷下，材料的變形和微觀損傷機理，以及利用高速沖擊空氣炮測定了改復合材料制備剃度復合板的穿透性能。With the very low water to cement ratio, rpc has ultra - high strength high ductility and low permeability. in this paper, the compressive strength of rpc can reach to a high point with the number approximately 135mpa. as illustrated from the study results, we can approve some fundamental conclusions : there are big effects on rpc with deferent kinds and properties of raw materials and deferent curing conditions ; stress - strain curve shows the process of destroy with rpc samples ; x - ray diffraction analysis indicates that heat treatment at temperatures 90 accelerate the hydration of rpc sharply, therefore, mechanical and microstructural properties of rpc are highly dependent on heat treatment ; it is believed that rpc materials have excellent resistance to chloride permeability ; during the heat treatment, the shrinkage of rpc developed quickly because of chemical reactions ; the rpc with slag mostly has the advantage of rpc without slag about resistance to solutions corrosion
研究結果表明：通過對rpc各組分摻量變化的研究，可以找到rpc的最優配合比；試件成型后的熱養護制度對rpc的性能影響巨大； rpc的抗壓應力?應變曲線可以反映出試件受破壞時微裂紋的擴展情況，剛纖維的摻入可以大幅改善rpc的韌性； rpc在成型后存在較大的收縮，而其中的化學收縮要遠遠大於乾燥收縮； rpc具有很強的抗氯離子滲透性能，漿體的密實度很高；通過x射線衍射實驗，可以發現rpc的膠凝體中ch晶體已經幾乎不存在，膠凝體主要由c - s - h凝膠和未水化水泥顆粒組成；在抗溶液侵蝕的實驗中，摻礦渣rpc的抗溶液侵蝕性能在絕大多數情況下要好於不摻礦渣試件，酸、堿溶液和浙江工業大學碩士學位論文摘要一些鹽溶液都會對rpc的結構產生侵蝕作用，但是機理各有不同。Thermal and welding residual stress often produces in the proceeding of the electronic package, the residual stress release and thermal deformations of the microelectronics will reduce the assemble intensity between the chip and package, and then debase the electrical performance of the assemble circuit, numerous thermal cycling will lead to thermal fatigue or thermal failure of the microelectronics
電子封裝器件在生產的工藝過程中，往往會產生熱殘余應力以及焊接殘余應力，殘余應力的釋放作用及器件在使用過程中的熱變形，會降低集成電路晶元與封裝體的結合強度，進而降低集成電路的電性能，反復的熱循環，將導致器件的熱疲勞失效，嚴重時可導致矽片或陶瓷片破裂，使整個器件遭到破壞。The carbon fibers with low strength are broken easily according to thermal tension and bend stress damage models, and the carbon fibers with high modulus are broken easily according to thermal shear stress damage model in spite of less damage caused by heat. the carbon fibers with surface glue of epoxy resin are damaged easily in physical and chemical ways because of high oxygen extent and rigidity of epoxy resin
低強度碳纖維容易在熱應力拉伸或彎折破壞模式下損傷；高模量碳纖維高溫損傷小，但國防科學技術大學研究生院學位論文容易以熱應力剪切破壞模式下斷裂;環氧樹脂表面膠剛性較大，氧含量較高，使碳纖維容易受到化學損傷和熱應力彎折損傷，均不宜用來制備c燈sic復合材料。分享友人