熱空氣導流管 的英文怎麼說
中文拼音 [rèkōngqìdǎoliúguǎn]
熱空氣導流管
英文
choke heater- 空 : 空Ⅰ形容詞(不包含什麼; 裏面沒有東西或沒有內容; 不切實際的) empty; hollow; void Ⅱ名詞1 (天空) s...
- 氣 : Ⅰ名詞1 (氣體) gas 2 (空氣) air 3 (氣息) breath 4 (自然界冷熱陰晴等現象) weather 5 (氣味...
- 導 : 動詞1. (引導) lead; guide 2. (傳導) transmit; conduct 3. (開導) instruct; teach; give guidance to
- 流 : Ⅰ動1 (液體移動; 流動) flow 2 (移動不定) drift; move; wander 3 (流傳; 傳播) spread 4 (向壞...
- 管 : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
- 空氣 : 1 (大氣) air; atmosphere 2 (氣氛) atmosphere 3 (氣閘) air brake4 pneum ; pneumo ; pneumat ;...
-
Firstly, simulate flow field of rear smoke channel, plot velocity magnitude and ash concentration distribution in section of entry of heat pipe air preheater, compare with data which were measured in guiyang power station, verify simulation to be reasonable and right. secondly, simulate all kinds of factors which affect flow field ' s uniformity such as length, thickness, location of diffluent board, ash concentration, ash diameter, and so on, find the chiefly factors. thirdly, install guide board in curve channel in rear smoke channel, then simulate its " flow field, plot velocity magnitude and ash concentration distribution
在此基礎上模擬在冬夏兩季不同情況下,不同流速對熱管空氣預熱器壁面溫度的影響;然後對影響整個流場分佈的各種因素:包括分流板長度、厚度、偏離中心流道位置的偏離度、飛灰濃度、飛灰粒徑等因素進行數值模擬;最後提出在分流煙道轉彎處加裝導流板,並模擬加裝導流板后的流場分佈,得到下級空氣預熱器出口、熱管空氣預熱器進口處的斷面速度場分佈、濃度場分佈,以論證加裝導流板能達到流場均勻化的作用。( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )
研究結果表明: ( 1 )超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐,在二維空間上呈軸對稱的雙峰分佈,負壓形成於這個倒渦流錐內; ( 2 )修正後的霧化氣體速度公式可以滿足超音速霧化的要求; ( 3 )影響超音速霧化工藝最根本的因素有氣液質量流率比( gmr )的大小、霧化氣體流量和倒渦流錐范圍,三個因素的值越大,對形成細粉越有利; ( 4 )在焊錫合金為zhl63a ,霧化介質微n _ 2 ,導液管突出高度取h = 6 . 0mm ,霧化氣體壓力取p = 1 . 0mpa ,合金過熱度取t = 167 ( t = 350 )時,所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。Hot air duct
熱空氣導流管Since frosting is inevitable so long as some physical factors are satisfied, it will enlarge the resistance of airflow, cut down the airflow rate of air cooler and reduce the coefficient of heat transfer. in order to keep the refrigeration system run smoothly, frost must be removed
結霜只要滿足一定的物理條件就是不可避免的,霜層增厚增加了空氣的流動阻力,冷風機盤管流量減少,同時霜層增厚也會導致傳熱系數下降,因此為保持系統高效運行,除霜是必須的。分享友人