燃燒率 的英文怎麼說
中文拼音 [ránshāolǜ]
燃燒率
英文
burn rate-
Low combustion efficiency and serious pollution problems come with the behindhand facilities and technology of coal combustion
由於燃煤設備和燃燒技術相對落後，因而帶來了燃燒效率不高和環境污染嚴重兩大問題。Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading
文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點Moreover, the system of powdered coal conveying with primary air is the most important tache, whether the distribution of primary air is even or not directly relates to whether the distribution of powdered coal is even or not in all firing implement and nozzles, sequentially directly relates to whether it is hard to take fire, whether the fire is stable, whether there is coking and how about the heat efficiency of the boiler, hi addition, if there is jamming and deflagrate in the system of powdered coal conveying with primary air, severe safety accident can be resulted
良好的煤粉配風是建立合理的爐內空氣動力工況和穩定燃燒的必要條件。而其中一次熱風送粉系統又是最重要的一個環節，一次風配風是否均勻直接關繫到煤粉在各燃燒器和各噴嘴中的分佈是否均勻，從而直接關繫到著火是否困難、火焰是否穩定、局部是否結焦以及鍋爐的熱效率高低。若一次風送粉系統發生堵塞和煤粉爆燃則可能引發嚴重的安全事故。Long - hole and geometrical proportion type of mixing unit is finally adapted in lpg supply system, and power and torque output of lpg engine are improved by increasing compression ratio, and ignition characteristic is tried to adjusted to satisfy engine performance. meantime emission performance and noise level of lpg engine at full - throttle and other various part - throttle operations are tested and compared with former gasoline engine. ( 3 ) it is verified by engine dyno tests that lpg engine has better synthesized performance at aspects of power and torque, fuel economy, as well as emission than former gasoline engine
選擇了等比例長孔式混合器控制空燃比；通過提高壓縮比來彌補動力性的損失；以動力性為主控目標，對最大功率點、最大扭矩點、中等轉速、最低轉速點所對應的發動機轉速做了點火特性的調節；通過空燃比的合理控制，直接改善發動機的動力性、經濟和排放指標；作為對缸內燃燒過程的理論分析，進行了燃燒特性的實驗測試；對原汽油機和新開發的液化石油氣發動機，進行了外特性和部分負荷特性以及怠速的排放及噪聲對比性測試。Already the home of the worlds largest and most efficient straw - fired power station, and europes biggest plant powered by poultry litter, the uk is to build a biomass - fired power station with an electrical capacity of 44 megawatts
作為已經擁有了世界上規模最大，效率最高的秸稈燃燒發電廠，以及歐洲最大的養殖家禽的廢棄物發電廠的國家，英國正在建設一座發電能力Semi - coke is production of gasifier, its combustion efficiency directly influenced power generation efficiency of the total system
第二代pfbc - cc系統中氣化爐產生的半焦在pfb爐內燃燒效率的高低直接影響到整個系統的發電效率。Ionic liquids are extensively studied in areas of chemical synthesis, separation technology, electrochemistry and material processing due to their unique properties such as high electrical conductivity, high thermal stability, low measurable vapor pressure and incombustibility
摘要由於離子液體具有電導率高、熱穩定性好、蒸氣壓低、不燃燒等優良性質，越來越多地應用於有機合成、分離、電化學和材料加工等領域。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義Energy consume, electric strength, insulation resistance, ground conductivity, leakage current, microwave leakage, power input, normal temperature, humidity treatment, glow wire, horizontal flame, vertical flame, tracking, ball pressure, rainproof, water splash, dustproof, salt fog, endurance, motor load test, cord flexing, cord pulling, pull & torque test, lamp replacement, construction check etc
能耗、電氣強度、絕緣電阻、接地連續性、泄漏電流、微波泄漏、功率、溫升、濕熱試驗、灼熱絲、水平燃燒、垂直燃燒、漏電起痕、球壓試驗、防雨淋、防濺水、粉塵、鹽霧、耐久性（壽命）試驗、電機負載試驗、電源線彎折、電源線提拉、拉扭力測試、燈頭互換性、安全結構檢查等。This simple treatment also rationalizes the observed insensitivity of burning rates to chemical factors and pressure level.
這個簡單表達式也能解釋觀測到的燃燒速率對化學因素和壓力量級的不敏感性。It is important that the dependence of the burning rate on both the local reactant character and the local gas dynamic environment be adequately represented.
恰當地表示燃燒速率隨局部反應物特性和局部氣動力環境的變化關系是很重要的。In the course of the early rig tests it was observed that, within limits, combustion efficiency was largely independent of the size of the fuel jet.
在早期的試驗器試驗時，已經發現在一定權限范圍之內，燃油噴注的大小對燃燒效率影響很小。The investigation has declared that the fuel injection with bq fuel pump had higher injection pressure, bigger fuel supply rate and shouter fuel supply duration, which would cause the fuel injection quantity and the fule - air mixture to increase during ignition delay period, the pre - mixed combustion to become acutely, and finally result in increased power levels of noise
研究表明，裝配bq噴油泵，噴油系統的噴油壓力較高，供油速率較大和供油持續時間縮短，使得滯燃期的噴油量增加，滯燃期內形成的可燃混合較多，預混燃燒劇烈，導致整機噪聲聲功率級增加。The ratio of air to fuel for which perfect combustion takes place is called stoichiometry.
實現完全燃燒時的空氣和燃燒的比率稱為化學當量比。In order to verify the effects of application in weather modification, some numerical simulation of stratus in henan province were earned out. the model used in this paper is a three - dimension model of iap
在模擬時，分別將新舊三七高炮配方的成核率、機載末端燃燒器煙條和液態二氧化碳的成核率帶入模式進行運算。In this paper, firstly the macro parameter of the series connection app was comprehensively analyzed, among which the trajectory location of the bullet emission and the terminal velocity of the bullet were mainly analyzed, and the feasibility of the series connection app to cope with explosive reactive armor was demonstrated. and then the macro design about the head of the series connection app was made, among which a particular analyse about the bullet " s launching process was made, from which we concluded the relation between the thickness of the airproof loop and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the velocity of the bullet detached from the carrier and the relation between the length of the bullet and the burning rate of the powder and the relation between the length of the bullet and the maximum pressure of the emission hole and the relation between the length of the bullet and the emitting time of the bullet, and the reasonable str ucture of the head of the carrier and bullet were designed, then the intensity of the head of the carrier was checked out using of the software of ansys
本文首先對子母式穿甲彈總體參量作了全面的計算分析，其中主要分析了子彈射出的彈道位置和必要的子彈著靶速度，論證了子母式穿甲彈對付爆炸式反應裝甲的可行性，然後對子母式穿甲彈彈頭部進行了總體設計，其中主要對子彈的發射過程進行了詳細的分析，得出了母彈彈頭部發射孔內閉鎖環厚度與子彈飛離母彈速度的關系、子彈長度與子彈飛離母彈速度的關系、子彈長度與火藥燃燒率的關系、子彈長度與母彈彈頭部發射孔內最大壓力的關系以及子彈的長度與子彈發射所需時間的關系，設計出了合理的母彈彈頭部結構和子彈的結構，並利用ansys有限元分析軟體對母彈彈頭部的強度進行了校核。Average burning rate
平均燃燒率Test method for rate of burning and or extent and time of burning of self - supporting plastics in a horizontal position
水平位置自支撐式塑料的燃燒率和或燃燒程度與燃燒時間測試驗方法By using the formula of mass burning rate, the effects of turbulence on combustion process are directly reflected all calculation results are compared with the experimental data and the conclusions in some references concerned as well and the results show the numerical solution reasonable
在質量燃燒率的計算中，直接反映了紊流對燃燒過程的影響。編制了計算程序，進行了變參數性能預測計算。Abstract : during the heating of scrap with carbon or hydrocarbon contented substances in some process, it will bring problems like explosion of carbon monoxide, fume and smell from oil volatilization, etc. ， if incomplete combustion occurs. through laboratory experiments, the time related variation of gas contents and post combustion ratio of fume during the heating of oil - bearing scrap are studied. the results show that the restrictive chain of reaction procedure is the thermolysis of oil ; that temperature and ( co ) / ( co2 ) ratio influence transformation ratio and post - combustion ratio under lower temperature ; that 900 is the temperature above which the complete reaction can be ensured at all ( co ) / ( co2 ) ratios
文摘:在某些廢鋼熔煉過程中，當爐料中含碳及碳氫物質且燃燒不充分時，會帶來煙氣中一氧化碳的燃爆、油污揮發時造成的煙霧、臭味等問題.通過實驗室裝置研究含油廢鋼在加熱過程中煙氣成分隨時間的改變以及二次燃燒率的變化，試驗結果表明，反應過程的限制性環節是油分的熱分解；在較低的溫度下（ co ） / （ co2 ）比例影響轉化率和二次燃燒率；而在任意比例下保證充分反應的溫度為900以上分享友人