燃燒計 的英文怎麼說
中文拼音 [ránshāojì]
燃燒計
英文
comburimeter-
Afterburner systems, designed to operate up to a stoichiometric overall mixture strength, are always fairly close to combustion instability or screech.
要使加力燃燒系統在理論化學組成量的總混合濃度下還在一直工作，這樣的設計通常都很接近於不穩定燃燒或振蕩燃燒。Abstract : apply computer simulation to the distribution pattern of air - flow without considering the cold condition of the combustion and compare the flow patterns under different designed circumstances. and the effect of the design of the partition in the air way of the burner on the flow and mixture of gas and air is especially studied. the result shows that the design of partition plays a very important role in strengthening the mixture of gas and air, but increases the loss of the resistance in the air way and the total pressure of the air way in same working conditions needs increasing
文摘:應用計算機模擬的方法，在不考慮燃燒的冷態情況下，研究了熱風爐燃燒室內的氣流分佈規律.在此基礎上，比較了2種不同設計方案的氣流流動特徵，尤其是研究了燃燒器空氣通道內阻流板的設置與否對空氣和煤氣的流動和混合的影響.結果表明，阻流板的設計對加強空氣和煤氣的混合有著極為重要的作用，同時也增加了空氣管道的阻力損失，在同樣的工況條件下需要提高管道系統的總壓力Because of its extensive application and underdeveloped research level in our country, this paper establish the numerical model of blank cartridge ejecting device, the whole process from blank cartridge burning to eject missile is analyzed by classic interior ballistic theory and gas dynamics. several simulation examples are given, and the effect of different parameter structure on ejecting device is discussed
鑒于這類系統在我國的廣泛應用與相對滯后的研究水平，本文針對三種類型五種型號的掛彈鉤建立了拋放彈彈射機構的數學物理計算模型，用經典內彈道和氣體動力學理論分析了火藥彈燃燒到彈射活塞完全推離懸掛物的整個過程。( 2 ) calculation of the combustion parameters the combustion parameters of hmx, rdx, hns - i and b / kno _ ( 3 ) were calculated with vlwr code. the thermodynamic function of boron oxide was fitted by method of the least square to janaf thermo - chemical table, and their coefficients were determined
（ 2 ）炸藥及點火藥燃燒性能參數計算應用熱力學程序vlwr計算hmx 、 rdx 、 hns -及點火藥b kno _ 3的燃燒性能參數及燃燒平衡產物組成，得到了與密閉爆發器實驗相近的燃燒性能參數。Exact computation of the burning surface area is lengthy.
燃燒面積的精確計算是非常繁難的。Abstract : in the research of internal combustion engine, recordingin - cylinder pressure and temperature is an essential technique to study the thermal cycle of internal combustion engine. the combustion analyzer developed in this study will give both the measurements at sampling points per crank angle or sampling cycle, calculate and show the real time parameters which decide the working process of internal combustion engine, such as pressure accelerating rate, indicateed mean effective pressure, cycle - to - cycle variation, heat release rate, etc. compared with the imported congeneric products, the analyzer has many advantages such as chinese interface, low price, easy operateing, convenience in maintainance and easy upgrading
文摘:為了測錄內燃機缸內的壓力及溫度，開發了一種內燃機燃燒分析儀.該分析儀由國產高速數據採集卡及自行開發的控制軟體組成.它不僅能精確設置每度曲軸轉角內采樣點的個數和採集循環數，而且在採集過程中能實時計算和表徵內燃機工作過程的壓力升高率、平均指示壓力、循環變動率、放熱率等參數.經實際使用以及與國外產品相比表明，此分析儀具有全中文界面、價格低、操作簡單、使用維護方便、功能便於擴充等優點This thesis establishes the main factor of heating surface slagging of no. 1 boiler, that it is due to irrational layout of furnace heating surface, improper angle of burner which lead to flames attaching to furnace walls. such deduction is built on the basis of necessity of analyzing the heating surface slagging, the type of coal, the design of the furnace and burner, the operational condition and other factors effecting slagging of boiler. the research is mingled with practical operations of no. 1 boiler in inner mongolia fengtai electric power generation co, ltd
本論文從分析燃煤鍋爐結渣問題必要性出發，從煤種、爐膛及燃燒器設計、運行工況等因素對鍋爐結渣的影響著手，結合內蒙古豐泰發電有限公司~ # 1鍋爐實際運行中存在的問題，確定了~ # 1爐受熱而結渣的主要原因是爐膛受熱面布置不合理，燃燒器角度不合適導致火焰貼壁所致。This thesis first studies the hydrokinetics, heat transfer characteristics, combustion and dynamics of cfbb. three types of single fuzzy controllers and a kind of synthetically fuzzy controller are designed, through the analysis of the control system of a certain plant
本文通過對循環流化床的流體動力學特性、傳熱學特性、燃燒特性和動態特性等方面的研究，設計了三種單模糊控制器和一種綜合模糊控制器，分析了某一電廠實際控制系統，並對方案進行了比較。Through the study on the character of hydrokinetics and heat transfer and combustion and dynamic of cfbb, three kind of single fuzzy controllers and a kind of synthetically fuzzy controller are designed, and control system is analyzed in some one power plant, and the three kind of control scheme are simulated on deferent objects
本文通過對循環流化床的流體動力學特性、傳熱學特性、燃燒特性和動態特性等的研究，設計了三種單模糊控制器和一種綜合模糊控制器，分析了某一電廠實際控制系統，並對這三種控制方案進行了變對象的模擬。In the article, the originator worked out the mechanism of magnesium - base alloys catching fire ; analyzed briefly the influence of the temperature, the heating velocity and the pressure of oxygen in the atmosphere on the lumps and scraps of pure magnesium ’ s catching fire, and designed a practical method to measure the kindling temperature of the lumps and scraps of pure magnesium precisely, with which the initial quantization of kindling temperature can be realized
本文圍繞鎂合金阻燃技術的開發作了許多基礎性的研究工作，通過分析大量的相關文獻和試驗結果，初步得出了塊狀鎂和鎂屑的燃燒機理，簡要分析了溫度、升溫速度、環境中氧的分壓對塊狀鎂和鎂屑的起火燃燒所產生的影響。設計出了精確度高、實用性強的塊狀鎂和鎂屑的燃點測試方法，使塊狀鎂和鎂屑的燃點得到初步的量化。By means of introduction digestion debug and absorption, the two softwares - ktvasv - lite and ktva - 3v run successfully on pc so that the definitions of variables scopes of values and the units and input format of the softwares are obtained,
Kiva是內燃機燃燒過程計算機模擬程序集的總稱。該程序集由美國人於1985年開發，歷經了從kiva到kiva3v - erc的六次不斷完善的飛躍。Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece
將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer
超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。Measurement precision contribute to improving the security class and economic of boiler running and automatic level of whole plant. the smart measurement instrument of the boiler ’ s air flow designed in the thesis and the instrument can make the degree of accuracy get to. firstly, the thesis build the “ velocity - area ” method which is on basis of “ log - tchebycheff ” on the analyzing of basic measure method of boiler ’ s air flow. secondly, model86 averaging pitot tube was selected the right model of flow transducer which can pickoff the differential pressure and static pressure. modelc264 which made in setra system corp. u. s. a was selected as ultra low differential pressure transmitter. a good flow of boiler ’ s air was calculated by offsetting pressure and temperature. finally, numeroscope was designed with z80cpu and other chips
精確的監測有助於提高鍋爐燃燒的安全型、經濟性，也有助於提高電廠的整體自動化水平。本文設計的智能化鍋爐風量測量裝置能夠實現對鍋爐送風的精確測量，精度可達。本文首先研究鍋爐送風矩形大管道測量理論，提出在流來流量測量測點布置基於「對數-切比雪夫」法的速度-面積法。Steps are revealed that must be taken when boiler without designed capability of peak shaving takes part in peak shaving operation : one is combustion adjustment, the other one modification of burner
明確了沒有設計調峰能力的鍋爐在參與電網調峰運行所應採取的措施：燃燒調整與燃燒器改造。Method for calibration of radiometers for use in fire testing
燃燒試驗用輻射計校準方法After getting online results, combustion expert controller gained relevant ratiocinate output results by integrating technical parameters of online inspected system, combustion computed results and diagnostic and manipulated countermeasure of knowledge base, then which could propose operator for choosing a suitable control method using concentrated corresponding rules
在得到在線計算結果以後，燃燒專家控制器綜合在線檢測系統提供的工藝參數，以及燃燒計算的結果，使用存放在知識庫中的診斷和操作對策，得到相應的推理輸出結果；利用規則集的相應規則，提示操作工選用合適的控制方法。In the third, this paper makes a survey on components of the exhausted flue gas and waste heat resource, and discusses the possibility and methods of steam generation and air preheating with the waste heat. and then, the analysis on the advantages and disadvantages of heat recovery plants with conventional steel - water heat pipes and inorganic heat - transfer heat pipes is carried out. the paper also gives a valuation about the plan and features of the design of heat recovery
對余熱源排煙的成分和余熱資源量進行標定，討論余熱回收產生蒸汽或加熱燃燒用空氣的可行性和方法，分析常規余熱回收技術設計、採用普通鋼-水熱管和無機傳熱熱管等傳熱元件的設計余熱回收裝置的優缺點，並對余熱回收設計方案及其特點進行總體評價。3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant
對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。Combustion results would be also applied to the combustion control loop
燃燒計算結果同時也應用於燃燒控制迴路。分享友人