燒結工段 的英文怎麼說
中文拼音 [shāojiēgōngduàn]
燒結工段
英文
sintering section-
The primary theory of absorption and desorption was also explained. the effects of primary process parameters, such as hydrogen pressure, time and temperature on the magnetic properties of ndfeb have been researched. the structure and magnetic properties have been analyzed by means of optical metallographic microscopy, scanning electronic microscopy, x - ray diffraction analysis, infrared oxygen detector and magnetic properties measurement
本文設計了燒結ndfeb的氫爆制粉設備，對設備調試以及使用過程中出現的主要問題進行了簡要的說明，提出了一系列解決方法；闡述了吸氫、脫氫的基本原理；研究了氫氣壓力、通氫時間、氫爆溫度等基本工藝參數對磁性能的影響；利用金相顯微鏡和掃描電子顯微鏡， x射線衍射分析，紅外線測氧分析及綜合磁性測量儀等手段分析了材料的組織結構和磁性能。This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation
本文針對該鍋爐在實際運行中存在的問題：在額定負荷下，爐膛出口超溫、低溫段過熱器前煙溫高達936 ，遠遠超過815的設計值；噴燃器四周水冷壁結焦嚴重，過熱器管壁溫度超標，無法帶上額定負荷；甚至有時因燃煤質量的變化，必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中，燃燒器的結構、布置，水冷壁的粘污、結垢，過剩空氣系數、一次風溫、煤種及其濃度變化等許多因素都會偏離鍋爐的設計工況，從而影響爐內的傳熱和燃燒，造成爐膛出口超溫、水冷壁結渣等問題。Analysis of experimental data indicates that there exist several following problems during the whole operation : first, the emission is serious and the density of hc and co smoke is very high at on and off period. second, there is oil dripping from the dripping vitta as a result of the fault of ignition system and combustion structure. the last, there might be accidents of disabled ignition resulted from the improper operation at the beginning
通過對樣機的試驗分析和研究表明，汽車空氣燃油加熱器在整個工作過程中，其排放存在以下三個問題：一、開機和關機兩個階段的排放問題嚴重，廢氣中hc和co的濃度值及煙度測量值都很高；二、因點火系統和燃燒結構的缺陷而導致開機后一段時間內有油滴從滴油管滴落；三、在點火過程中，會出現因操作不當而點火失效的現象。Avoiding the difficulties of detecting the difficult parameters in furnace control and of building up the models, integrated with fuzzy control and conventional pid control, abb ’ s control it system is used to predict the bloom surface and center temperature directly based on the temperature of furnace wall easily to be detected so that the temperature settings in various furnace sections can be self - corrected, the furnace temperature of each section self - adjusted and on - line parameters of combustion control self - optimized. in addition, the heating parameters and the operating status of the field plant can be monitored with alarm
採用abb公司的controlit控制系統，避開爐子控制中遇到的困難參數檢測及建模困難等因素，直接根據容易檢測的爐壁溫度來推知鋼坯表面溫度及鋼坯中心溫度，將模糊控制技術與常規pid控制相結合，實現各段溫爐設定值自修正、各段爐溫自協調、各參數在線自整定的自尋優最佳燃燒控制;對熱工參數、現場設備的運行情況進行監視、報警，實現爐膛壓力、管道壓力、換熱器的保護控制，並將重要參數送往廠級mis網路。Rapid prototyping technology changed the traditional pattern of product design, which could offer product sample for the designer, reduced design cycle and quicken the schedule of new product design, and it gave the decision - makers visual feeling. ; rp technology provided kinds of molds including resin - boncled mold laminate mold, investment mold and lost foam casting mold and so on for sand casting investment casting and cavityless casting, it could also use direct shell production casting to make pattern dies metal dies die - casting dies injection dies directly, and it could even produce casting products in small scales. the applications of fdm technology in plaster precision casting and the rapid casting technology based on sls technology were introduced, the organic combination between rapid prototyping tecnnology and foundry process, which initiated a new period of rapid manufacturing metal parts, by using advanced new technology alternated traditional foundry industry to make it looked brand - new, thus, the competition of foundry industry would be improved ; rapid prototyping technology offered a rapid economical feasible technical method, common processes of using rapid prototyping technology to produce dies were discussed, in the paper it explored that. the problem of combining rapid prototyping technology with electric arc metal - spraying technology to make metal dies and technics in dies manufacturing of combining rapid prototyping technology with precision casting, rapid tooling based on rapid prototyping, integrated advanced new technology and tradition technology of rapid prototyping manufacture, each superiority were exerted, rapid prototyping technology had been an efficiency measure to rapid update products and develop new product, and to middle -
快速成型技術改變了傳統的產品開發模式，可以為設計者提供產品樣件，縮短設計周期，加快新產品的開發進度，為決策者提供直觀性；快速成型技術迅速提供砂型鑄造、熔模鑄造、實型鑄造用的各種模樣，包括樹脂模、層壓模、熔模和消失模等，還可採用直接制殼鑄造法直接製造熔模鑄造用的壓型、金屬型、壓鑄型、注塑模，甚至直接製造小批量鑄件，介紹了熔積成型技術在石膏型精密鑄造上的應用和基於選擇性激光燒結技術的快速鑄造技術，快速成型技術與鑄造工藝的有機結合，開創了快速製造金屬零件的新階段，對用高新技術改造傳統的鑄造工業，使其面貌煥然一新，增強鑄造行業的競爭能力；快速成型技術為母模的製造提供了一條快速、經濟、可行的技術途徑，討論了利用快速成型技術製造模具的一般工藝方法，探討了將快速成型技術與金屬電弧噴鍍技術結合起來快速製造金屬模具問題，以及快速成型技術與精密鑄造技術相結合的模具製造工藝，基於快速成型製造的快速模具技術，集成了快速成型製造高新技術和傳統技術，發揮各自優勢，已成為產品快速更新換代和新產品開發及中、小批量生產的有效手段之一。Application of the sx three functions - wet type deduster in mixing system of hegang sintering plant
濕式三效除塵機組在合鋼燒結廠混料工段的應用Focusing on the performance evaluating and the design of tripropellant injector, adopting the cold test rig with background pressure supply, malvem particle analyzer, ccd photography system, tripropellant hot test - bed, numerical simulation software and auxiliary theoretical a nalysis, the d ischarge c haracteristic a s w ell a s a tomization p erformance o f the injector and the combustion performance as well as the mode - transition characteristic of thrust chamber are studied detailedly based on the 3 different structures of coaxial tripropellant injector, large numbers of important conclusions are gained
本文圍繞三組元噴嘴的性能評定及設計方法。採用反壓冷試臺、馬爾文測粒儀、 ccd高速攝影系統、三組元發動機熱態試驗臺、數值模擬程序及輔助理論分析等多種技術手段和研究方法，對三種結構的同軸式三組元噴嘴深入進行了噴嘴流量特性和霧化特性、推力室燃燒性能和轉工況性能研究，得到了大量重要結果。This paper systematically discussed the fundamental, characteristics, research status and equipment of microwave sintering, and introduced the preparation and development of sintered ndfeb magnets, on the basis of which the effects of the parameters on the heating rate and sintering temperature were investigated. and by means of optical metallurgical analysis, x - ray diffraction analysis and the measurement of density and magnetic properties, the paper compared the properties and technology of ndfeb magnets sintered in microwave magnetic field with that of magnets sintered in conventional heating process
本文系統論述了微波燒結基本原理、特點、研究現狀和燒結設備，介紹了燒結ndfeb制備工藝和發展，在此基礎上研究了微波磁場燒結ndfeb永磁材料過程中各因素對升溫速率、燒結溫度的影響，並通過金相顯微分析、 x射線衍射分析、密度及磁性能測試等手段，將微波磁場燒結的ndfeb磁體與常規燒結的磁體進行了工藝與性能的對比分析。Chapter 3 introduces black - liquor evaporation and combustion process in alkali recovery. models used in alkali recovery control are summarized and an overview of the alkali recovery control are given. the problems in alkali recovery control research and its development trend are discussed too
2 ）第三章介紹了堿回收過程燃燒和蒸發工段的工藝流程，總結分析了國內外對堿回收過程建立的各種模型，概述了堿回收過程先進控制的研究現狀和研究成果，並指出了理論研究與實際應用中所存在的問題，以及以後研究的方向。On the base of the development of thick film pastes technology, ru - based thick film resistor pastes have been studied due to select conductive phase and inorganic binder. state - of - the - art techniques such as rolling, screen printing and sintering were used for sample preparation. effects of ingredients, printing parameters and sintering parameters, microstructure on the properties of thick film resistor ( trf ) have been analyzed with xrd, sem, dsc and electrical tests
本文在跟蹤國內外厚膜漿料技術發展的基礎上，以釕酸鉍/銀系厚膜電阻漿料為研究對象，通過選用合適的功能相和無機粘結相成分，以三輥軋制、絲網印刷和高溫燒結等制備工藝為技術特徵，採用xrd 、 sem 、 dsc等分析方法和電性能測試手段，系統的研究了漿料中各相的成分配比、制備工藝參數，以及膜層微觀結構對厚膜電阻性能的影響規律。In order to solve the problems effectively, under the auspices of 863 plan in china, the synthesis diagnosis has been carried by means of measuring and numerical imitating the combustion chamber of refining column, and some conclusions is such as : ( 1 ) through measuring the temperature and combustion in the burning chamber of the refining column, the result shows the temperature difference on the same level is more than that in height direction, and there is a few of co in bottom of burning chamber. ( 2 ) in order to ensure normal work of flue system in lead column in the course of zinc refining, theoretic calculation and measure about the flow resistance of exhaust gas are carried through. the results of study reveal that drawing out force of chimney is inadequate, which is mainly caused by illogicality of flue construction
在研究過程中，採取了現場實測和數值模擬手段對韶關冶煉廠鋅精餾鉛塔燃燒室及排煙系統進行了綜合診斷，具體結果包括如下： （ 1 ）完成鋅精餾鉛塔燃燒室內溫度測試以及燃燒狀況的測試，結果發現：鉛塔燃燒室內水平方向的煙氣溫度並非均勻，而且其溫差比上下方向的溫差更大，以及鉛塔燃燒室尾部存在co未燃燼問題； （ 2 ）為了保證鉛塔煙氣系統的正常工作，對煙道系統的阻力進行了理論計算及測試分析，結果發現：鋅精餾鉛塔煙氣系統中煙囪抽力不夠，這主要是煙道結構不合理所造成的。These produels are produced by the techniques same with chemical bonded non - sintered bricks with semi - silica raw materials, they have high strength, good heat insulating and alkali resistant properties, they are mainly applied to the zones of large - sized cement rotary kilns which are croded badly by alkali, for example, the input zone, preheater, three - windtunnel, and decomposing zone
本產品採用半硅質原料，以化學結合不燒工藝生產而成，它具有強度高、隔熱效果好、抗堿侵蝕能力強的特性，主要用於大型水泥回轉窯筒入料區段、預熱器、三次風管和分解帶等堿侵蝕嚴重的部位。Rces scope of engineering supply comprises basic engineering for the grinding, briquetting and sintering section as well as for the calcining, electro - fusion, crushing and screening section and detailed engineering for the shaft kiln plant
的供貨范圍包括：研磨造球和燒結部段以及煅燒電鍍熔合碾壓篩選部段的基本工程以及該豎窯的詳細工程。The parameters of impregnation are as follows : ph is about 3, the range of temperature is from 20 to 45, and the time is about 2 to 6 hours. after the necessary treatments, zirconia cloths had the optimal strength when the diameters of zirconia fibers were controlled in 4um to 7um, and the sizes of zirconia grains were in 50nm to 100nm. the affec - ting factors were discussed and the liner regression analysis of the cloths was made, from w hich they show that the diameters and grain sizes have the significant influences on zirconia cloths. the obtained zirconia cloths have been accepted for use in nickel - hydrogen batteries by practical use
研究結果表明：粘膠類纖維布最適合制備氧化鋯纖維布的前軀體；鋯液濃度以飽和溶液為宜；浸漬工藝參數為ph值3左右，溫度20 45 ，時間2 6小時；多餘鋯鹽的去除、浸鋯液后纖維布的整平處理及平燒施應力燒成有利於氧化鋯纖維布的柔軟及平整; 200 600燒成溫度段應緩慢燒成，控制氧化鋯纖維直徑在4 7 m ，氧化鋯晶粒尺寸50 100nm時氧化鋯纖維布的強度最好。These include the new heavy plate bay facility, incorporating new burning equipment and a 5, 000 - ton press needed to process thick plate structures, and new covered modular assembly, outfit and unit assembly facilities
這些投資包括最新的厚鋼板加工設施，包括了處理厚鋼板結構所需要的新的燃燒設備和一個5千噸壓力機，還有新的有棚的模塊化組裝，整體和分段組裝設施。Abstract : establishment of the macro dynamic mathematical models for coked zeolite catalyst coke burning regeneration was discussed from an engineering point of view. based on the modified particle - pellet model, dynamic mathematical equations for porous and nonporous catalyst coke burning regeneration were deduced, supplying a theoretical basis for computer simulation of coked zeolite catalyst regeneration
文摘:從反應工程學的角度討論了結焦沸石催化劑燒焦再生反應宏觀動力學數學模型的建立，根據已提出的修正的顆粒-粒子動態等溫物理模型，分別推導出了多孔焦炭的燃燒再生階段數學方程和無孔焦炭的燃燒再生階段數學方程，為結焦沸石催化劑再生反應過程計算機模擬提供了理論依據。Spinel limn2o4 begin to form at 350 with the sintering time of 4 hours because there are one li + and two mn2 + in one precursor molecule. when the sintering temperature is larger than 750, a specific sintering route is designed to avoid the formation of li2mno3 impurities
前驅體的焙燒溫度和焙燒時間對limn _ 2o _ 4樣品的晶相結構有很大的影響，焙燒溫度高於750時，應採用分段焙燒工藝以防止局部高溫形成li _ 2mno _ 3雜質。In the section of non - pressing sintered, the influence of different raw material system and sintered temperature on the phase composition of the material were studied. and two conclusions were achieved. the one is that it is good for phase composition design and control because the final phase composition of the material fabricated by ti, sic and c raw material system is comparatively stable
在無壓燒結階段，研究了原料體系與工藝制度對材料物相組成的影響，結果表明使用ti 、 sic 、 c的原料體系得到的材料最終物相組成比較穩定，有利於進行材料組成設計與控制； 1500得到的材料中的雜質相含量較少，是比較合適的反應溫度。For adapting to the need of industrialization and improving the properties of materials, the method of mechanical activation has introduced on the basis of traditional calcinations at high temperature. the stardard spinel limn204 is prepared by the mechanical activation - high temperature solid synthesis method. the thermodynamic property, the physical - chemistry performance and the producing techniques of. battery have been studied by means of thermogravimetry ( tg ), differential scanning calorimetry ( dsc ), x - ray diffraction ( xrd ), scanning electric microscopy ( sem ) as well as various electrochemical analysis methods. studies show that synthesis temperature, calcinations time, recipe of raw materials, heat treatment and particle size of products are main factors affecting the performances of limn204 cathode materials. with the increment of synthesis temperature and time, the structure and crystal of products are getting to perfect
隨著合成溫度和時間的增加，產物的結構和晶型越趨于完善，但在1100得到的產物有燒結和晶粒增大的現象，恆溫時間超過24h后對材料的性能影響不是很大； li mn比在0 . 95 1 . 05 2的條件下都可得到標準的尖晶石limn _ 2o _ 4 ，尤其當li mn比為1 . 05 2時，所合成的材料具有較好的電化學性能；通過兩段合成法制備的產物性能要比一段合成法法制備的產物性能好，而兩段間隔合成法比兩段連續合成法處理的材料性能更佳；顆粒的粒度隨著球磨時間的延長而減小，比表面昆明理工大學碩士學位論文摘要卻增大，粒度小且分佈范圍窄的材料有利於鏗離子的擴散。The cathodes both of the prepared tungsten - based barium - tungsten cathode and mixed metal barium - tungsten cathode have, not only high current density, but also a long life, simplified procedure and stable performance, and so on. and we made certain two good additives cr2o3 and ni2o3 that make the cathode performance more excellent
2 ）對不同元素配比的二元和三元混合陰極基底的制備工藝和發射性能開展了實驗研究，在增大發射能力，延長壽命和降低燒結溫度等方面有重要進展，取得了有價值的階段成果。分享友人