爆炸加工法 的英文怎麼說

中文拼音 [bàozhájiāgōngfǎ]
爆炸加工法 英文
explosive shaping
  • 爆 : 動詞1. （猛然破裂或迸出） explode; burst 2. （放在滾油里快炒） quick-fry
  • 炸 : 炸動詞1. （在油里弄熟食物） fry in deep fat or oil 2. [方言] （焯） scald （as a way of cooking）
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 爆炸 : explode; blast; blow up; bomb; burst; detonate; explosion; fulmination; out-burst
  1. Abstract : the stimulation treatment of & quot; loosening rock by the dilatancy of explosive waves & quot; is tested in the casing well 4242 for studying its result and its influence on casing. the result of the field test shows that this test is successful in technology, the oil production of the well is 4 times as much as that of it before the test ; the deformation of casing is local, and the result of the strength calculation shows that the deformation will not destroy casing

    文摘:為了研究「壓脹松動」增產技術的增產效果和對套管的影響，在延長石油管理局子長油礦對4242井進行了現場實驗.該技術採用強動載波在地層深處疊加的方法，造成壓脹條件，松動巖石，增大近井帶滲透率，提高油井產量.施工后，該井產量增加為原來的4倍多.本次實驗工藝上是成功的，首先是按設計要求引爆了炸藥，其二是由於採取了保護措施，使套管變形局限在施工段處，不影響下泵，不影響油井生產;套管強度校核分析也證明了套管不會破壞.施工后地質效果明顯
  2. The method of strengthening the charging at the bottom of the blasting - hole is usually described in traditional teaching - books and blasting engineering, which is used to overcome resistance at the bottom

    傳統的教科書和工程爆破中通常是採取孔底超深加強裝藥或底部採用猛炸藥的方法，用以克服底部阻力，消除根底。
  3. An application of blast method to squeeze mud and replacement with controlled loading

    控制加載爆炸擠淤置換法在工程中應用
  4. The influence of specific charge, hole arrangement, charge structure, stem length, millisecond interval and ignition mode on the yield of the blasted boulder is analyzed some measures to lower boulder yield in deep hole blasting of underground mine are presented through the optimization of blasting operation parameters as follows : lowering deep hole blasting effect of geology structure, rationally determining specific charge, using technique of wide - space small burden blasting, technique of manifold charge structure and technique of millisecond compression blasting, strengthening the management of boring construction and blasting construction

    該優化技術措施主要有：減少地質構造對深孔落礦的影響，合理確定炸藥單耗的方法，使用大孔距小抵抗線落礦技術，採用多種裝藥結構技術，採用多排微差起爆技術，加強深孔的施工管理和加強爆破施工的現場管理。
分享友人
分享到 Line

分享到臉書