特徵曲面葉 的英文怎麼說

中文拼音 [tèzhǐqūmiànyè]
特徵曲面葉 英文
characteristic sheet
  • 特 : Ⅰ形容詞（特殊; 超出一般） particular; special; exceptional; unusual Ⅱ副詞1 （特別） especially; v...
  • 徵 : 名詞[音樂] （古代五音之一 相當于簡譜的「5」） a note of the ancient chinese five tone scale corre...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  1. At the surface of the pollen grains there are three types of aperturates, including three porates type, three colpates type and three porate - colpates type ; and four types of sculpture, namely, reticulate, striate, striate - reticulate and verrucate. the upper epidermal cells of the leaves of 12 species plants are detected with hpias - 1000 image analytic system through the treatment of binarization, and the experimental methods are proved stable. the results indicated that the waviness of the anticlinal walls ( sfc ) and the ratio of the feret ' s diameter ( slf ) of the epidermal cells of the middle lamina in the third node of leaves starting from the lowerest part of the stem have a relative constant range and could distinguish from each other. oieanolic acid, l, 5, 8 - trihydroxy - 3 - methoxyxanthone and swertiamarin are separately detected on the tlc, and the different chromatogram of various plants can be considered as characters of identification. the contents of oleanolic acid in 12 species of plants are determinated by hplc, but among the different plants and botanical organs their contents are different, and the highest content in flowers

    本文對川鄂產獐牙菜屬藥用植物資源進行了野外調查、標本採集和鑒定，對12種乾燥藥材的性狀進行了描述，提供了可以鑒別的特徵。通過掃描電子顯微鏡觀察的12種本屬藥用植物的花粉粒均為單粒花粉，萌發孔有3孔型， 3溝型和3孔溝型三種類型；表面紋飾包括網狀紋，條狀?網狀紋，條狀紋和瘤狀紋四種類型。用hpias ? 1000高清晰度彩色病理圖文分析系統對葉片上表皮細胞作圖像分析，並進行方法學研究，結果表明，同種植物莖上第3節葉片中段主脈和第1側脈之間葉上表皮細胞垂周壁彎曲程度sfc值和細胞縱、橫向直徑的比值slf值，種間有顯著差異，每種都有相對恆定范圍值。
  2. This paper presents a design method of propeller blade section operating in non - uniform flow field and an idea of equivalent operating curve with unchanged cavitations characteristic on blade section, the method for selecting the curve is set up

    摘要給出了非均勻流場中螺旋槳槳葉剖面的設計方法，提出了保持剖面空泡特徵不變的等效運轉曲線的思想，並創建了等效運轉曲線的確定方法。
  3. As the basic concept, the first step is to modeling by ug. there is different model between propeller and commonly hardware, so we must be use curve modeling, at the same time, characteristic modeling and entity modeling in the whole process. first, we apply offset data for spline fit curve, then scanner smooth curve face

    首先在三維繪圖軟體ug中對螺旋槳及葉片進行三維建模，由於螺旋槳的造型不同於一般零件的cad造型，故在造型過程中同時採用了曲面造型，特徵造型和實體造型幾種方法，先由型值數據生成樣條曲線，再由樣條曲線掃掠生成平滑的曲面，最後通過圓整?延伸得到螺旋槳的三維模型。
分享友人
分享到 Line

分享到臉書