現場澆注的 的英文怎麼說
中文拼音 [xiànchǎngjiāozhùde]
現場澆注的
英文
cast in place- 現 : Ⅰ名詞1 (現在; 此刻) present; now; current; existing 2 (現款) cash; ready money Ⅱ副詞(臨時; ...
- 場 : 場Ⅰ名詞1 (平坦的空地 多用來翻曬糧食 碾軋穀物) a level open space; threshing ground 2 [方言] (...
- 澆 : 澆名詞(姓氏) a surname
- 注 : Ⅰ動詞1 (灌入) pour; irrigate 2 (集中) concentrate on; fix on; focus on 3 (用文字來解釋字句)...
- 的 : 4次方是 The fourth power of 2 is direction
- 現場 : 1. (出事地點) scene 2. (工作地點) site; spot; on-site; work field
-
Standard test method for compressive strength of concrete cylinders cast in place in cylindrical molds
在圓柱模型中現場澆注混凝土圓柱體的抗壓強度標準試驗方法Used to concrete seam and arbitrarily shape seam in component. in the condition of the expanding being favorable limited, attain satisfied stop - water effect and manage the concrete interstitial leaking. at the same time, it can be also used to shipping and engine etcindustrial equipment
適用於現場澆注的混凝土施工縫和嵌入構件任意形狀的接縫內,在其膨脹受到良好限制的條件下達到滿意的止水效果,治理混凝土裂縫的漏水,同時也用於船舶、機車等工業設備的防水密封。Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process
在相同的注射條件下,通過分析喂料在不同直徑和長度流道中的流動規律,得到了喂料在流道中的速度場、壓力場和溫度場,找到了流道長徑比的合理取值范圍,並得出通過改變流道設計可實現對現有設備資源充分利用的結論;給出了不同注射壓力下,型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線,得到了注射壓力對充填時間和型腔壓力的影響規律,確定了最佳的充模時間、注射時間和注射壓力;通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈,預測了注射件的成形質量,或可能產生的注射缺陷及位置,優化了澆口設置。During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied
在溫度場的模擬中,模擬結果表明,保壓時間是影響製件成形質量的關鍵因素之一,擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大,需進行參數之間的協調,只有當變形區內部始終維持準固態時,才能實現穩定的液-固擠壓成形過程;在變形場的模擬中,根據液態浸滲擠壓的成形特徵,選用了雙曲正弦剛-粘塑性有限元計算模型,研究了變形過程中應力應變場的變化規律,研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。The computing model is optimized according to the model board trolley installation form and the concrete pouring process
根據現場測量時模板臺車的結構安裝形式和混凝土澆注的施工步驟,反復修整完善計算模型。Wear resistant layer of cylinder and double - layer liner in catalyst creaking apparatus ( without or with tortoiseshell net can be used ), inner liner of carbon monoxide exhaust - heat boiler, pouring at site for furnace roof with high temperature of heating furnace of steel rolling, different forging furnace, resistance furnace, the prefabricated parts can also be made
催化裂化裝置中的筒體耐磨層及雙層襯里, (無龜甲網和有龜甲網均可採用)及一氧化碳余熱鍋爐的內襯,也適用於軋鋼加熱爐、各種煅造爐、電阻爐的爐頂、爐墻、爐底高溫部位的現場澆注,可製成預制構件。According to the tendency of modern concrete pump deliever with far - distance and high - floor pouring, the market need a measure system provided with good automatic performance and friendly human - machine interface
現代混凝土泵送技術向遠距離傳輸、高層澆注發展,並日益走向市場化,對測量系統的要求越來越高,不但要求它具備較高的自動化程度及良好的測量性能,還要求友善的人機交互界面。Standard specification for installation of cast - in - place reinforced gypsum concrete
現場澆注的增強石膏混凝土構件安裝的標準規范Cold pour resin compound and heat - shrink cable joints in the voltage range up to 1000 v a. c. and 1500 v d. c. code of practice for on - site installation
電壓范圍為交流1000v和直流1500vd . c .的低溫澆注樹脂復合物和熱縮電纜接頭.第2部分:現場安裝實用規程分享友人