球形壓頭 的英文怎麼說
中文拼音 [qiúxíngyātóu]
球形壓頭
英文
ball indenter-
On the base of the basic structure study of the tooth - locked quick closure vessel of middle and low pressure with crown head, the optimization method of parameterized whole device is presented in this paper, the emphases of research is put on optimization of the tooth - locked quick closure device whose structure and load distribution is complicated, the wall of vessel, however, is designed according to the existing strength formula
本文對帶有球冠形封頭的中、低壓齒嚙式快開容器的基本結構進行研究的基礎上，提出了齒嚙式快開容器的參數化整體優化方法，研究重點放在結構和受力復雜的齒嚙式快開裝置的優化，對于容器簡體壁厚仍採用現有強度公式設計。Press tolls. quick release punches and dies. ball check device
沖壓工具.快速拆卸的沖頭和沖模.球形閥裝置Tools for pressing. ball - lock punch retainers. part 1 : types a and b, rectangular and square for light duty
沖壓工具.球形閥沖頭限動器.第1部分:小功率用途的a或b型，矩形及正方形沖頭Optimization design of the connecting zone of spherical head and cylinder of high pressure vessels
高壓容器球形封頭與筒體連接區優化設計Compression couplings with spherical liner ; equal tees
帶球形襯的壓接管接頭.等長度三通連接管Compression couplings with spherical liner ; equal elbows
帶球形襯的壓接管接頭.等長度彎管Compression couplings with spherical liner ; equal crosses
帶球形襯的壓接管接頭.等長度四通連接管Compression fittings with spherical liners ; adaptars for welding
帶球形襯的壓接管接頭.焊接轉接器Compression couplings with spherical liner ; male studed banjo bolts for ring type nipples
帶球形襯的壓接管接頭.環形套管的插樁式鼓形螺栓Compression couplings with ball - type nipples - complete unions and survey
帶球形襯套的壓接接頭.完整接頭和概述Ball ends for swaging on cable
鋼纜冷壓連接用球形頭This dissertation investigates the influences of internal press and missiles shape on deformation and rupture of a multi - span thin - walled metal tube that struck by a large - mass and slow - speed missile transversely. 103 impact tests were conducted on a thin tube ( d / t = 44 ) either empty or filled with water using a missile ( dm / t = 6 ) with various nose shapes ( flat - nosed, hemisphere - nosed and conical - nosed )
採用三種彈體（平頭、半球形和圓錐頭，彈體直徑與管壁厚度之比d _ m t = 6 ）對空管和高壓充水薄壁鋼管（徑厚比d t = 44 ）進行了沖擊破壞實驗，預加工作內壓分別為0mpa ， 5mpa ， 10mpa和15mpa 。16mnr and 45 # steel are taken as examples. the obtained results have been applied to analyze the safety of operation pressure and rationality of design of a kind of engineering structure - a flange joint of hemispherical head to cylindrical shell. try to seek a sort of new method to assessment the capability of structure to load beyond the traditional method which regards stress and strain as main parameters
本文以45 ~ #調質鋼和壓力容器常用鋼材16mnr為研究對象，對金屬材料韌性斷裂的斷裂模式進行細觀機理上的研究，進而分析一種工程結構? ?採用與筒體厚度不同的半球形封頭的壓力容器的筒體連接結構? ?的靜載變形特點和破壞形式，嘗試在以應力應變為主要參數的傳統方法之外，尋求一種新的結構承載能力分析的方法。The stresses and strarns of cylindrical spherical and paraboloid shells can be solved when the drawing unsteadiness happen
文中就圓柱殼形、圓球殼形、拋物線殼形封頭等壓力容器的失穩狀態，分別求出它們的應力和應變。Compression couplings with spherical liners - adaptors with parallel screwed - in ends
帶球形襯里的壓緊聯軸節.平行旋入式接頭3. spherical joint 13 place may be welded with lead pressure tube
3 .球形接頭13處可與引壓管焊接6. spherical joint 13 place may be welded with lead pressure tube
6 .球形接頭13處可與引壓管焊接分享友人