理論收縮限度 的英文怎麼說

中文拼音 [lǐlúnshōusuōxiàndù]
理論收縮限度 英文
theoretical shrinkage limit
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 論 : 論名詞（記錄孔子及其門徒的言行的「論語」） the analects of confucius
  • 收 : Ⅰ動詞1 （把攤開的或分散的事物聚集、合攏） put away; take in 2 （收取） collect 3 （收割） harvest...
  • 縮 : 縮構詞成分。
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 理論 : theory
  • 收縮 : 1 （由大變小; 由長變短） contract; shrink 2 （緊縮） concentrate one s forces; draw back 3 take u...
  • 限度 : limit; limitation; measure; tether
  1. Based on theoretical analysis and computational model, a three - dimension numerical simulation software 3c3d ( concrete cracking control 3d ) was finished in which finite element and finite difference method were both hired. compared with the known data, good agreement proved it reliable and practicable. finally, by means of the software, with variant of environmental temperature and relative humidity and different curing conditions, the variety regulation of temperature and humidity and the stress due to them within concrete were analyzed

    然後針對收縮開裂的本質因素即混凝土內部的溫度梯度和濕度梯度，進一步從理論上分析了高強高性能混凝土早期溫濕度場隨齡期發展的分佈情況，分析溫濕度變化與收縮變形的關系，建立了相應的計算模型，並且採用有限元和有限差分方法編制三維模擬系統軟體3c3d （ concretecrackingcontrol3d ） ，通過與已知數據的對比分析，驗證了該模型的可靠性和實用性。
  2. The thermal stress of ceramic regenerator resulting from its temperature difference and restricted extension and contraction has been calculated and analyzed, the result provides a theoretical basis for design and operation of high temperature air combustion system

    對于由溫度分佈不均勻，陶瓷蓄熱體膨脹或收縮受限制而產生的熱應力進行了計算和分析，其結果為蓄熱式高風溫燃燒系統的設計及運行參數的選擇提供了理論依據。
  3. First, according to the demand of vimp for resin system, the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined. then vimp based on a high - permeable medium and grooves are studied by visual experiments, through which the appropriate high - permeable mediums are selected and the parameters of width, depth and spacing for flow grooves and spacing for supply grooves are optimized. furthermore, various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion

    文中首先根據vimp對樹脂體系的要求，對vimp用不飽和聚酯樹脂體系的動力學和流變學性能進行了研究，確定了最佳低收縮添加劑的含量；對高滲透介質型和溝槽型vimp開展了實驗研究，通過可視化實驗優選出較好的高滲透介質，確定了引流槽的寬度、深度和槽間距及主槽的槽間距等工藝參數並進行了優化；對影響充模過程的各種因素進行了詳細的討論，並以模型船和夾芯面板的製作為實例描述了兩種vimp的成型過程；在實驗的基礎上，建立了二維滲漏模型，採用控制體有限元法對高滲透介質型vimp進行了成型過程的計算機模擬計算，通過充模時間和流動前峰的計算值與實驗結果的比較，驗證本文所採用的數學模型和數值方法的正確性，其結果對實際生產具有一定的理論指導意義。
分享友人
分享到 Line

分享到臉書