界面擴散 的英文怎麼說

中文拼音 [jièmiànkuòsǎn]
界面擴散 英文
interfacial diffusion
  • 界 : 名詞1 （相交的地方; 劃分的界限） boundary 2 （一定的范圍） scope; extent 3 （按職業、工作或性別等...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 擴 : 動詞（擴大） expand; enlarge; extend
  • 散 : 散動詞1. （由聚集而分離） break up; disperse 2. （散布） distribute; disseminate; give out 3. （排除） dispel; let out
  • 界面 : [物理化學] interface; boundary; limiting surface
  1. The diffusion welding behavior of single - crystalline cu to single - crystalline - aio with a nb film interlayer and the joint microstructure properties were studied by tem, sem / eds analyses and four - point bend testing. the nb film interlayer deposited by electron beam evaporation on the ceramic side prior to diffusion welding was found to be olycrytalline and fiber - textured after diffusion bonding, with the close - packed plane ( 110 ) being parallel to the ( 0001 ) basal plane of - aio

    擴散連接技術是一門邊緣科學，涉及材料、擴散、相變、界面反應、接頭應力應變等各種行為，工藝參數多，雖然已經進行了大量的試驗研究，但卻對各種材料的連接機理尚未有明確的認識，為此人們試圖藉助于計算技術，對接頭行為進行數值模擬，以便找到共同規律，對擴散連接過程及質量進行預測與實時控制。
  2. Interfacial atoms diffusion or covalence by a circulated - argon ion bombardment process could improve the adhesion strength between the coatings and the uranium substrate

    循環氬離子轟擊鍍方法可促進使膜-基界面原子間的擴散或鍵合，有利於提高膜-基結合強度。
  3. Jin - hsiang lo and whei - may grace lee, 1994 / 9, experimental study of fugacity capacity of hydrophobic organic compounds in atmospheric fog, proceedings of the 7th iuappa regional conference on air pollution and waste issues

    羅金翔，李慧梅， 1994 / 10 ，霧粒中界面活性物質對有機污染物擴散揮發之影響，第十一屆空氣污染控制技術研討會論文專輯
  4. The boundary condition at bed surface of diffusion equation of nonuniform sediment is derived based on the concept of exchange intensity of stochastic theory by the author

    摘要文中首先給出了由我們建立的床面泥沙交換理論導出的非均勻沙擴散方程的邊界條件。
  5. Finally, some simplification methods to the model were studied and a modified block elimination contraposing the features of the model ' s linear system was developed, which can greatly decrease the model ' s requirement to computer resources. in the second part, numerical methodology of hybrid techniques was developed, which uses dfn models developed in the fist part to build continuum approximations of fractured rock

    第三，本文將一種用離散的水?氣分界面模擬非飽和滲流的數值模型擴展到裂隙網路中，為用本文所構建的離散裂隙網路模型模擬裂隙巖體成富擁要柳廳錄非飽和滲流提供了一個初步的框架。
  6. The fluid molecular clusters near the interface crack to form smaller fluid molecular clusters through collision, and then fall into the aqueous phase. the smaller fluid molecular clusters continue breaking through disturbance, collisions and attraction by the neighboring molecular clusters. the process continues until a single fluid molecule is formed

    溶解不是以單個分子的形式擴散進入水相中，而是相界面的流體分子簇通過碰撞、裂解成小規模分子簇后落入水相，在水相中繼續受周圍分子簇的持續擾動、碰撞和吸引作用解體，最終成為單個流體分子。
  7. In the paper we mainly researched space gainp2 / gaas / ge high efficiency tandem cells " making process by home - made low pressure mocvd technology and new solar concentrators. firstly, we presented reseached and development of solar cells in china and foreign countries ; secondly, on the basis of fundamental priciples and theories, we discussed some factors of influcing conversion efficiency of solar cells, and analysed the i - v output feature of two - junction tandem cells ; then the design concept of gainp2 / gaas / ge two - junction tandem cells was discussed, the detailed aspects of gainp2 / gaas / ge tandem cells epitaxy growth by low pressure mocvd was studied, and some questions on epitaxy growth ( such as crystal qualities, interface stress, element interdiffusion, n - and p - type doping et all ) were solved ; after that, the cell fabrication process was described ; finally, we reseached the hot pressing and mould process technology of an arched line - focus fresnel lens made by pmma, designed and fixed new solar concentrators

    本文致力於用自製的低壓mocvd裝置進行cainp _ 2 / gaas / ge空間用高效級聯太陽能電池製作的工藝以及聚光太陽能電池組件的研究。首先，介紹了國內外太陽能電池的研究現狀及應用情況；其次，運用太陽能電池基本原理討論影響電池轉換效率的因素，分析了級聯電池的伏安特性；隨后，討論了cainp _ 2 / gaas / ge雙結級聯電池的結構設計理念，研究了採用低壓mocvd技術生長cainp _ 2 / gaas / ge級聯太陽電池材料的工藝過程，解決了異質材料生長的結晶質量、界面應力、材料互擴散以及材料n 、 p型摻雜等一系列問題；然後總結了級聯電池的后工藝製作；最後，研究了以pmma為材料的菲涅耳線聚焦透鏡的熱壓成型工藝及其模具的加工工藝，設計並安裝完成新型聚光太陽能電池組件。
  8. The hydration theory and the structure forming of hplc are analyzed through xrd, sem, edxa, and the analysis of pore structure, micro hardness. the model of the interface structure between lightweight aggregate and harden cement paste is divided into 4steps, which are penetrating, hydrating and hardening, diffusing of moisture and ion, forming of optimal interface structure, and the ideal structure model of lightweight aggregate is built

    採用xrd 、 sem 、 edxa 、孔結構分析與顯微硬度技術分析了高性能輕集料混凝土的水化硬化機理及結構形成過程，把輕集料與水泥石之間界面結構形成過程分為滲透、水化硬化、水分遷移與離子擴散、界面結構優化四個階段，提出了輕集料與水泥石之間的界面結構模型和高性能輕集料的理想結構模型。
  9. In the interface an interdiffused layer with multphases would be formed during the process of welding or operation at elevated temperature. because of so much difference between the interdiffused layer and the original interface layer, it would influence the welding strength severely

    在焊接過程中以及經過較高使用溫度的長時間使用后，鈮合金同不銹鋼界面會產生材料組分元素的互擴散，形成互擴散層，互擴散層的性能與原始界面的性能有較大差別，影響焊接強度。
  10. On the basis of analysis for experimental data, the relationship of power between evaporation mass and time for naphtha was found and the average value of the power is about 0. 70

    原油的蒸發幾乎不受風速、液池面積的影響，這說明原油的蒸發受邊界層條件控制的程度很小，其蒸發速率主要由其自身性質（如分子擴散系數、蒸氣壓等）所決定，其蒸發過程是受基本蒸發過程式控制制的。
  11. The exchange rates of po4 - p in the east china sea were correlated with the temperature, ph of the seawater and mainly influenced by the reaction at the surface of the sediments. the exchange rates were controlled by the do and ph. it was shown that relationships between the exchange rates of no3 - n, no2 - n and nh4 - n and the potential environmental controls were complicated

    Po _ 4 - p在沉積物?海水界面的交換作用受擴散過程的影響不大，而界面上的反應，如fe氧化物對摘要p04一p的吸附和解吸，可能是po4一p交換速率的主要控制過程， do濃度和ph值可能是主要的控制因子。
  12. Xps depth measurement suggested that the films were compositionally homogeneous along the growth direction ; that the interdiffusion between znsxse1 - x and ito was not serious in this deposition process ; and a sharp interface had developed

    Xps深度剖析顯示所制備的薄膜，其內部成分均勻，無偏析和凝聚，界面清晰而陡峭，擴散不嚴重。
  13. In this study the main form of the nitrogen that diffused from sediment into overly water was ammonia, and the submerged plant decreased the diffusion fluxes of ammonia and nitrate at water - sediment interface

    總之，水沉積物界面氨氮是沉積物向上覆水擴散的主要氮組分，沉水植物降低了氨氮和硝態氮的擴散通量。
  14. In the suspended sediment transport model, the method of shear stress is adopted to determine the source function in the suspended sediment diffusion equation. through a series numerical experiments and statistical analyses of observed field data, a local coefficient, which can reflect the bottom material and consolidation, is introduced into the classic critical erosion velocity of the sediment

    懸沙輸運模型利用切應力方法來確定對流擴散方程中的泥沙源函數，其中的臨界起動速度利用經典的泥沙起動流速公式前面增加一個局地系數得到，這個系數能反映河床底質結構及固結程度，通過系列數值試驗和實測資料的統計分析確定。
  15. Under the background of the research work - " expert system of hydraulic brake system design for saloon car, small and medium passenger car " for nanjing yuejin automobile group, in this paper, a set of special cad software for vihicle brake was developed in which the researchful object was brake, . the cad supporting software was pro / engineer and the developing language was vb. the project of discreted brake was raised and 3d graphic parametric library of typical parts and assemblies was established. 3d solid modeling and parameter - driven between dimensions and relations were accomplished using pro / engineer

    本文以南京躍進汽車集團的橫向課題「轎車、中小型客車液壓制動系設計專家系統」為背景，以制動器為研究對象，以pro engineer為cad支撐軟體，採用vb語言，開發了一套汽車制動器專用cad系統；提出了制動器離散化方案，構建了參數化的制動器典型零部件三維圖形庫，使用pro engineer實現三維實體造型以及尺寸與關系的參數化驅動；圖形庫系統採用參數化圖庫引用、管理機制並擁有一個開放的擴充介面；研究了pro engineer二次開發模塊pro toolkit ，解決了同步模式下定製程序界面的問題，並實現與pro engineer的通信；建立了制動過程數學模型，推導了制動方程式並給出相關解法，編制了制動器數值模擬分析程序；構建了制動器設計資料庫。
  16. The calculated results show that the main reason why the g as carburizing process is accelerated is due to the obvious increase in the diff usion coefficient and transfer coefficient of carbon resulted from the addition of re

    稀土元素加速滲碳過程的主要原因是增加了碳在奧氏體中的擴散系數，同時提高了碳的界面傳遞系數。
  17. Abstract : a new simulating method is established for the calcul ation of the hardness profile of high - carbon - concentration deep - carburization, on the basis of analyzing this process and taking into account the influence o f carbide solution and dissolution, carbon - concentration and temperature on the diffusion behavior, and the influence of the environment factor on carbon trans fer through the gas - solid interface

    文摘:在對高濃度深層滲碳的特點進行分析的基礎上，考慮到碳化物的析出與溶解、溫度及碳濃度對擴散行為的影響，氣氛環境對相界面碳傳遞過程的影響，淬火烈度對滲碳層冷卻效果的影響，提出了一種新的模擬高濃度深層滲碳滲層硬度分佈的方法。
  18. There are distinct changes about shifts or intensity in bulk plasmon, surface plasmon, and interband electron transitions losses as a result of oxidation of specimens, and adsorption and oxidation processes can be studied through these changes. at room temperature, the formation of oxide layers on uranium and uranium - niobium alloys were found to occur rapidly upon exposure to oxygen, and the resultant oxide in each case was near - stoichiometric uo2. due to formation of niobium oxide in uranium - niobium alloys, the diffusion of o ~ ( - ) ( o ~ ( 2 - ) ) and u ~ ( 4 + ) in the interface region was prevented, and the corrosion resistance of uranium - niobium alloys to oxygen is greatly enhanced by alloying with niobium

    研究結果表明：清潔表面鈮和鈾的體等離子體振蕩所造成的電子能量損失的實驗值與理論計算值較為符合；隨著氧化程度的加劇，表面等離子體（ sp ） 、體等離子體（ bp ）以及價帶電子躍遷所造成電子能量損失的譜峰發生了明顯的連續偏移或強度的變化，這些變化可以用來分析鈾及鈾鈮合金的初始氧化過程；室溫下，鈾及鈾鈮合金很容易與氧作用，最終結果，鈾僅氧化為二氧化鈾，另外，在鈾鈮合金氧化過程中，因為有鈮的氧化物存在，不利於氧和鈾在界面擴散，增強了鈾鈮合金抗氧化性能； eels能獲得樣品表面的信息比aes更為表面，更為靈敏，但由於eels的譜線過于集中，主要在幾十ev以內，也有不容易區別和解譜的不足。
  19. But long time anneal will cause thermal degradation the whole spin - valve because of interlayer diffusion

    但長時間的高溫退火處理將會造成自旋閥其它各層之間的界面擴散，影響其性能。
  20. Abstract : a numerical model and experiments over pmma are used to evaluate the main assumptions used in the theoretical description of a diffusion flame established in a natural boundary layer. flow characteristics ( 2 - d boundary layer ) and surface thermal balance are identified as the critical assumptions to be evaluated. comparison of experiments, numerical results, and theoretical model serve to validate the assumptions leading to the definition of a mass transfer number but establish the need to model all three - dimensional features of the flow

    文摘:對pmma進行數字模擬和試驗，對描述自然邊界層擴散火焰理論的假設進行評價.我們把流動特性（二維邊界層）和表面熱平衡作為評價的關鍵假設.試驗、數字模擬和理論模型證實了對質量傳遞數值定義的假設是正確的，但研究也表明，有必要對流動特性進行三維模擬
分享友人
分享到 Line

分享到臉書