皮泡沫體 的英文怎麼說
中文拼音 [pípāomòtǐ]
皮泡沫體
英文
integral skin foam-
The steady dead generation and time that was caused by the isolated virus was certain by chicken embryo which was inoculated on seven or nine days. the histopathological changs of the infectious stunting syndrom were studied by the way of ordinary paraffin section and he dying. the experimental result were as follows : the test proved that the changes of the chicken embryo were different in different stage. the chicken embryo dead in a week after it inoculated. the body was dropsy and hemorrhage. dead before it hatched out, the embyo body were dropsy, pale and slime. the liver was yellow and swolled, gallbladder ( vesica fellea ) was filled with bile. bursa and glandula thymus analosis. the kindey dropsy. bowel lamina were humble, dilatation. gas and yellow foam were filled the bowel. histopathological changes were that, in early stage, obvious changes of liver and kindey were dropsy, hemorrhage and necrosis. two types eosinophilic intranuclear inclusion bodies including large round and little granular were present in cells of the above organs. the obvious changes of bursa were dropsy, adverse folliiculated growth and little lymphocytes proliferating, 19 - 21 days chicken embryo, one or two big empty vacuoles were prensent in cells of liver and kindey. the number of the folliculi was growing, the vacuoles between cells were larger
膽囊充盈、其內充滿稀薄的膽汁；法氏囊、胸腺萎縮，腸道擴張、腸壁菲薄、內充滿氣體及黃色泡沫狀物；腎臟腫大。病理組織學變化方面，早期肝臟、腎臟、腸主要以出血、水腫和壞死為主，且肝細胞核及腎小管的上皮細胞核內均發現有核內包涵體，包涵體呈嗜酸性，為大型圓形包涵體或不規則的顆粒狀；法氏囊則以水腫、濾泡發育不良、小型淋巴細胞數量增多為主。 19 21日齡雞胚肝細胞、腎小管上皮細胞的胞漿內出現1 2各大的空泡，法氏囊濾泡數目增多細胞間有較大空隙。According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling
依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
分享友人