直接電模擬 的英文怎麼說

中文拼音 [zhíjiēdiàn]
直接電模擬 英文
direct electrical analogue
  • : Ⅰ形容詞1 (成直線的; 硬挺的) straight; stiff 2 (跟地面垂直的; 從上到下的; 從前到后的) erect; v...
  • : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
  • : Ⅰ名詞1 (有電荷存在和電荷變化的現象) electricity 2 (電報) telegram; cable Ⅱ動詞1 (觸電) give...
  • : 模名詞1. (模子) mould; pattern; matrix 2. (姓氏) a surname
  • : 動詞1. (設計; 起草) draw up; draft 2. (打算; 想要) intend; plan 3. (模仿) imitate
  • 直接 : direct; immediate
  • 模擬 : imitate; simulate; analog; analogy; imitation; simulation模擬艙 boilerplate; 模擬電路 [電學] circ...
  1. This paper discusses the designing and making of the dynamic testing systems of engine electronic control system. base on the construction and operation principle of santana 2000gsi m3. 8. 2 engine electronic control systems, design and manufacture led circuit of dynamic testing and fault imitating electronic control unit. on the inspect board, design and equip with motronic 3. 8. 2 ecu i / o measuring joints, design and set up obd - ii diagnostic communication link, design and install fuel pressure inspecting meter. depend on the obd - ii diagnostic communication link and ecu i / o measuring joints, this dynamic testing system can inspect engine electronic fuel injection system, distributorless ignition system, idle speed control system and evaporative emission control system, and can inspect m3. 8. 2 sensors, ecu and actuators, and can interrogate fault memory and erase fault memory ; and can analyse data stream ; and can carry out fault imitating. besides, this paper analyses sensors and actuators typical fault w aves

    2控單元路連器設計製成輸入輸出子控制檢測端子,並在檢測面板上布置了obd -診斷插座和燃油壓力表。使該動態測試系統能實現對噴發動機的燃油系統、點火系統、怠速控制系統和燃油蒸氣排放控制系統的動態檢測;並通過obd -診斷座、 ecu輸入輸出檢測端子和故障處理單元實現對噴發動機控系統各傳感器、控單元、執行器進行故障碼讀取與清除;動態數據讀取和波形測試和故障等。此外,本論文還分析了傳感器和執行器典型故障波形。
  2. Depend on the comprehensive analysis and study of the structure, principle, and exterior characteristic of the motor, through the methods of system modeling and digital simulation analysis, two kind of control device that work for the low voltage ( lvdc ) and the high voltage ( hvdc ) in avigation are researched respectively. point to the control technique of close - loop speed stabilization at a limited adjustment speed range, we bring out the close - loop speed control method that using the rotor position sensor indirectly measure the speed of the motor

    在全面分析了稀土永磁無刷動機的結構特點、工作原理、運行方式以及外部特性的基礎上,通過系統建和數字分析,分別針對航空低壓流( lvdc )和高壓流( hvdc )兩種動機構用永磁無刷動機,在小范圍轉速連續調節下的閉環穩速控制技術進行了詳細理論研究,提出了利用轉子位置傳感器信號間測量機轉速進行機轉速閉環穩速控制的策略。
  3. Integrating the power flow program with the tools matlab simulates the transient response of the distribution networks with the direct combination wind generator under disturbances, it provides the credible rationale to the research on stability and maximal penetrable power

    本文結合配網潮流程序,利用matlab作為工具,包含並網風能轉換系統的配網路在受到擾動情況下的暫態響應,對含有風場的力系統穩定性研究及風場極限穿透功率的研究,提供了可靠的理論根據,有重要的現實意義。
  4. Basing on the analysis about the reason that how the superabundant torque appears, direct torque control strategy is used to realize the servo control of two asynchronous motors and load system ' s simulation. the measure method of superabundant torque of the system, the valid method of static state torque and the benchmark of dynamic torque are given by testifying the system ' s speediness through experiments

    在具體分析加載系統中多餘力產生原因的基礎上,採用轉矩控制策略,實現了兩臺異步動機伺服控制和加載系統的負載實驗,通過實驗驗證了系統的快速性;給出了系統多餘轉動慣量的測量、靜態轉矩的校驗和動態轉矩基準的實驗的基本方案。
  5. Direct acting indicating analogue electrical measuring instruments and their accessories part 5 : special requirements for phase meters, power factor meters and synchroscopes

    動作指示氣測量儀器及其附件.第5部分:相位表功率因數表和同步示波器的特殊要求
  6. Direct acting indicating analogue electrical measuring instruments and their accessories. part 5 : special requirements for phase meters, power factor meters and synchroscopes

    作用指示測量儀表及其附件第5部分:相位表功率因數表和同步指示器的特殊要求
  7. Direct acting indicating analogue electrical measuring instruments and their accessories - specification for special requirements for phase meters, power factor meters and synchroscopes

    指示工測量儀表及其輔助設備.第5部分:相位表功率因數表和同步指示器的特殊要求規范
  8. Direct acting indicating analogue electrical measuring instruments and their accessories ; part 5 : special requirements for phase meters, power factor meters and synchroscopes iec 60051 - 5 : 1985, edition 4 ; german version en 60051 - 5 : 1989

    顯示的器測量儀及附件.第5部分:相位表功
  9. However, since memory circuit is very large and dense and the growing of its size is amazing, it is unpractical to extract the logic parameter directly with simulation tools

    然而,由於存儲器單元密集和路龐大的特點,並且存儲器的增大極為迅速,使得用工具提取邏輯參數並不現實,存儲器的簡化迫在眉睫。
  10. The carrier wave is modulated directly by the baseband signal at several frequency point in l band and s band. firstly, this paper clarifies the theory of i / q modulation, elaborates evm and acpl, and analyzes the effect of amplitude and phase unbalance and dc offset on evm. secondly we review the basic principle of phase locked loop and it ’ s composing parts, including the basic conception and design method of pll frequency synthesizer, especially introduce the charge pump pll frequency synthesizer in detail

    首先,在闡述i / q正交調制基本原理的基礎上,通過對誤差矢量和鄰近通道功率泄漏的詳細分析,定性、定量地討論了各種非理想路因素(如相位不平衡、幅度不平衡、流偏差等)對調制器性能的影響;其次,介紹了鎖相環的工作原理和基本組成部分,包括鎖相環的設計和環路濾波器的設計,特別詳述了荷泵鎖相頻率源;第三,介紹了採用調制技術衛星信號的射頻前端的設計;最後,對整個射頻調制系統進行測試,結果基本上達到了課題要求。
  11. Flexible dimming control utilizes either an analog control signal or direct digital pwm control without external rc filtering. this also increases dimming accuracy at low brightness levels

    路採用靈活的調光控制方式,既可輸入控制信號,也可輸入數字脈沖寬度調制信號而不需要外置rc濾波器。
  12. Direct acting indicating analogue electrical measuring instruments and their accessories. part 6 : special requirements for ohmmeters impendance meters and conductance meters

    動作指示氣測量儀器及其附件.第6部分:歐姆表
  13. This paper mainly focuses on the noise limiting by means of the direct sequence spread spectrum ( dsss ) and the analysis of the transmission performance of the plc and some digital modulation technology. the contents of the paper is as follows : 1 ) the technical feasibility is proved after simulating noise limiting principle of dsss by means of systemview, the simulation software ; 2 ) a kind of band pass filter ( bpf ) is realized according to the requirement of filter and the principle of butterworth approximation, which satisfies the index of performance of dsss. 3 ) the low voltage plc system includes the sc1128, the specific modulation / demodulation ic, the bpf filter and other circuit components, furthermore, the control function of system is realized by means of the personal computer and the microcontroller

    本課題在對低壓力線的傳輸特性和數字調制技術進行分析的基礎上,將通信理論中的序列擴頻技術( dsss )用於解決低壓力線通信的干擾問題,主要研究內容如下: ( 1 )用通信軟體systemview對dsss技術的通信和抗干擾原理進行分析,分別對時域和頻域下採用dsss技術前後收信號的頻譜進行分析,驗證dsss技術在本系統中的可行性; ( 2 )由dsss技術對濾波系統的要求,根據濾波理論分析了巴特沃思型濾波器的逼近原理並設計了合適的濾波路; ( 3 )用調制解調晶元sc1128和自行設計的濾波器加之輔助外圍路,構造出低壓力線載波通信系統,並採用atmel公司的單片機設計了收和發射路的微控制器; ( 4 )分別對採取抗干擾措施前後輸入和輸出信號進行對比實驗,並對結果進行分析,驗證了dsss技術對干擾信號的抑制作用。
  14. This paper studies the variable - voltage energy saving theory and its implementation for asynchronous motor with light load, compares several kinds of scheme of improving efficiency in detail and confirms the variable - voltage energy saving method, that is adjusting the input voltage by detecting the iron loss and copper loss of motor directly. in addition, the directness *, simpleness and availability of the method are verified by the emulational experimental results with simulink of the matlab. the circuit of the general inverter based on the tms320f240 dsp was used in this paper, and the practicable program was compiled

    本文分析了異步動機輕載時降壓節能運行的原理,對幾種提高效率的方案進行了比較,確定了通過檢測動機鐵損和銅損來實時調節輸入壓以達到高效節能目的的控制方法,應用matlab軟體對系統進行,在基於tms320f240dsp的通用型變頻器上編制了實用化的程序,形成了完整的樣機,對其進行了測試,並給出了試驗結果。
  15. The subject of this thesis is to study ironless moving coil linear permanent magnet synchronous motor and the major works in this thesis are summarized as follows : 1 ) two analytical formulas are derived by concentrated current method and distributed current method to determine the magnetic field due to pm, based on the current model of pm. besides, two method ( magnetic charge method and solution by laplace equation method ) are also introduced with comparing their advantages and disadvantages. then the effects of the motor parameters on the flux distribution are discussed

    本文對空芯動圈式線同步動機進行了深入細致的研究,內容包括: ( 1 )採用型推導出兩種計算永磁磁極二維氣隙磁場的解析公式(集中流法、分佈流法) ,同時介紹了兩種永磁機氣隙磁場計算方法(磁荷法,求解拉氏方程法) ,分析各種方法的優缺點,討論機參數對氣隙磁密的影響; ( 2 )介紹了單層同心繞組的布置方式,根據安培定律推導出空芯動圈式線永磁同步動機的靜推力計算公式,分析靜態力?位移特性; ( 3 )建立空芯動圈式線永磁同步動機動態型,不同驅動方式下動機起動、穩態運行時磁力、速度、位移的變化情況。
  16. Direct acting indicating analogue electrical measuring instruments and their accessories part 6 : special requirements for ohmmeters impedance meters and conductance meters

    動作指示氣測量儀器及其附件.第6部分:歐姆表
  17. Direct acting indicating analogue electrical measuring instruments and their accessories - specification for special requirements for ohmmeters impedance meters and conductance meters

    顯示測量儀表及其附件.第6部分:歐姆表
  18. The process control in an automatic control system is usually carried out by adjusting feedback of increments ; therefore, the electronic simulation of increment function can be used to study the performance of a system instead of practical system, the research expenses can be cut down and the hard and danger at the experimental site can be avoided

    摘要自動控制系統中的過程式控制制,都是通過增量回饋調節實現的,因此,若將其增量函數進行,並以該型代替實際系統進行系統的性能研究,則能大量減少研究經費的投入和避免過多現場實驗可能造成的危害。
  19. For the direct current decouple controller, the p1 adjustor ? parameter of current and voltage loop ? is designed. the correction of the designed parameter is testified by simulating on two phase synchronization coordinate and three phase stationary coordinate, the simulation wave is given

    流解耦控制器的流環和壓環的pi調節器參數進行了設計,並通過在兩相同步坐標系與三相靜態坐標系的驗證了設計參數的正確性,同時也驗證了流解耦控制方案的可行性,給出了波形。
  20. This paper sets up a simulation model and presents a method of digital realization

    關于流控制,建立了它的型,並介紹了數字化實現的方法。
分享友人