直線流動 的英文怎麼說

中文拼音 [zhíxiànliúdòng]
直線流動 英文
linear flow
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 直線 : 1. （不彎曲的線） straight line2. （急劇的） steep; sharp
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  1. According to the system technology require, adopting singlechip realize open loop digital control of hdclsm ; using v / f conversion and complex key - control method realize digital setting of system parameter, such as velocity ; using micro - stepping control insure the motor running more smoothly ; adopting debasing speed control method to eliminate the mechanical impact of distance termination effectively ; at the same time, analyzing main power circuits drive circuit and protect circuit of system, completing hardware design and facture and software programming and debugging ; at last, making a whole test in hybrid rotary step motor. the experiment result indicates that this control system reaches the qualities required and run smoothly also

    根據系統技術要求，採用單片機實現了混合式直流直線步進電動機的開環數字控制；利用v f變換和復合鍵控方法實現了系統轉速等參數的數字設定；利用細分控制技術保證了電機運行的平穩性，並進行了波形分析和理論研究；採用單片機軟體降速控制策略解決直線步進電機行程末端的機械沖擊問題；同時對主功率電路、驅動電路和系統保護電路進行了分析，完成了硬體設計、製作和軟體編程、調試，最後在混合式旋轉步進電動機上進行了全面測試。
  2. The tube is graduated so that flow rate can be read directly on a linear scale.

    管上刻以標度，所以從線性標度上可以直接讀出流動速率的數值。
  3. Second, we discuss the influence of environmental referance potential temperture and thermal wind on mesoscale symmetric instability. we find the expression of disturbance stream function and criterion of symmetric instability by analytical method and conclude that change caused by environmental referance potential temperture with height and thermal wind make critical richardson number and disturbance critical half - wave length of symmetric instability larger, that is to say, they benefit the occurance of symmetric instability. third, we study nonlinear perturbation analysis of mesoscale vertical circulation and evolution equation by means of f - plane. non - hydrostatic balance and filiter model

    第二，討論了環境位溫與熱成風因子對中尺度對稱不穩定的影響。運用解析的方法求出了擾動流函數的表達式和對稱不穩定的判據，發現環境參考位溫隨高度的變化與熱成風因子使得對稱不穩定臨界理查遜數及擾動的臨界半波長都變大，這有利於對稱不穩定的發生。第三，採用f平面、非靜力平衡、濾聲波模式，討論了中尺度垂直環流非線性攝動分析及演變方程。
  4. We can use the mm5 model in definite time, definite area weather forecasting. we conclude that : : the moving route of this necw in its developing progress was direct - south along latitude, the cold air is rough, and just this made the rough vertical velocity ; the necw southern moving and conflicting with the west pacification sub - tropical high makes rough jet steam. the plenty south - west warm and wet air made by the jet stream gave the rainstorm demanded vapor ;. the rough vertical velocity by jet stream is a main reason in this rainstorm ; the mm5 model uses four - direction analysis data as its input, this avoids some errors occurred in observe and transfer, thus made the result more useful

    綜合分析認為： （ 1 ） 、這次冷渦在其發生發展過程中，其移動路徑是沿經圈直線南壓，攜帶的冷空氣勢力較強，形成槽后較強的垂直運動； （ 2 ） 、西太平洋副熱帶高壓偏北位置與東北冷渦南壓形成的急流軸，把源源不斷的西南暖濕氣流輸送到遼西地區，也就是急流軸的左前方位置，為這次暴雨的產生提供了充足的水汽來源； （ 3 ） 、低空急流不但為暴雨輸送水汽，其造成的較強的垂直環流也是產生強降水的一個主要原因； （ 4 ） 、 mm5模式以四維同化資料作為初始場，最大限度地避免了觀測誤差可能造成的積分不穩定，提高了模擬結果的參考價值。
  5. An air straightener should be placed down stream from propeller to counteract circular air motion in the tube.

    一種氣體直線流動器應該使氣流從推進器的反作用中使氣體的活動在管內循環。
  6. The thesis roots in the item supported by " fifteen " aviation funds, - new type aeronautic linear dc motor ( ldcm ), study its classes characteristics and work principle, mainly researches the drive and control technique of aeronautic linear dc step motor ( ldcsm ) using in emergency discharging oil valve on airplane

    本文源於「十五」航空支撐基金項目-新型航空用直線直流電動機。論文研究了直線直流電動機的分類、特點及其工作原理，重點針對飛機應急放油閥用航空直線直流步進電動機驅動控制技術進行了研究。
  7. Drawing capstans are arranged in straight - line, the metering capstan is driven by separate dc motor. drawing dies can be quickly changed

    鼓輪直線式排列，定速輪單獨直流電機驅動，可實現快速換模功能。
  8. Moreover, the aeronautic linear dc motor control system not only can instead the drive motor of emergency discharging - oil valve, but also can be used in some low power electromotion machine making linear locomotion. the motor owns extensive application foreground preferably

    該直線直流步進電動機驅動控制系統的研製，可替代現有飛機應急放油閥有刷驅動電機，也可用於小功率直線運動機構中，具有較好的應用前景。
  9. The product is suitable for double straight line smoothing of grinding flat glass. coarse grinding, fine grinding, and polishing can be done at one time. adopt plc control system, which sets processing parameters via interface, and finishes processing at one time, ti has stable bottom structureprecise and smooth transmission system, the transmission belt drive adopts strong power and tran - sfrequency motor to control speed, constant power, constant rule, output and advanced equipment to control, completed product has high polishing level, which is an ideal option assistant processed equipment of processing delicacy glass and furniture glass factory

    本產品適用於磨削平板玻璃是雙直線平邊，粗磨精磨拋光一次完成採用plc控制系統通過界面設定加工參數次完成加工，具有穩重扎實的底座結構，精確流暢的傳動系繞，傳送皮帶驅動採用功率變頻電機調速控制，恆功率恆扭矩輸出和高配置的控製成品拋光亮度高是加工精品玻璃和傢具玻璃廠家使用的最佳輔助加工設備。
  10. The subject of this thesis is to study ironless moving coil linear permanent magnet synchronous motor and the major works in this thesis are summarized as follows : 1 ) two analytical formulas are derived by concentrated current method and distributed current method to determine the magnetic field due to pm, based on the current model of pm. besides, two method ( magnetic charge method and solution by laplace equation method ) are also introduced with comparing their advantages and disadvantages. then the effects of the motor parameters on the flux distribution are discussed

    本文對空芯動圈式直線同步電動機進行了深入細致的研究，內容包括： （ 1 ）採用電流模型推導出兩種計算永磁磁極二維氣隙磁場的解析公式（集中電流法、分佈電流法） ，同時介紹了兩種永磁電機氣隙磁場計算方法（磁荷法，直接求解拉氏方程法） ，分析各種方法的優缺點，討論電機參數對氣隙磁密的影響； （ 2 ）介紹了單層同心繞組的布置方式，根據安培定律推導出空芯動圈式直線永磁同步電動機的靜推力計算公式，分析靜態力?位移特性； （ 3 ）建立空芯動圈式直線永磁同步電動機動態模擬模型，模擬不同驅動方式下電動機起動、穩態運行時電磁力、速度、位移的變化情況。
  11. Abstract : in this paper, the kinematically admissible velocity fields are established by using the metal flow patterns based on the experiments, and the configuration dimensions of billet and the curves of load - stroke in precision forging process for spur gear from solid billet are simulated on computer by upper bound method. the results acquired in the simulation are in good agreement with those obtained in the experiments

    文摘:本文利用有實驗根據的變形流動模式建立動可容速度場，利用上限法模擬用實心坯料精鍛直齒圓柱齒輪時坯料的外形尺寸變化和力?行程曲線，所得結果與實驗測定值很一致，可供沖擠精鍛工藝設計參考。
  12. The primary of linear induction motor which drives the metro is installed on the chassis bogie, and because it is quite strict with laying down railway rail to use flat linear induction motor to drive metro, its secondary - - - - reaction board ( called induction board ), which is a kind of compound board of aluminum and steel, is fixed on the rail sleeper between the track. it is the airgap which is a gap between the primary and secondary of lim. the electromagnetic airgap is a very important parameter of lim

    利用有限元法對直線感應電動機二維非線性渦流場進行了數值計算，並在此基礎上，運用電磁場有限元分析的專用軟體ansoftmaxwell2d對單邊型直線感應電動機的瞬態特性進行了模擬分析，得到電機運行過程中的電磁推力、法向力、初級電流、氣隙磁密等曲線，通過改變直線電機參數，分析了電機氣隙對其瞬態性能的影響。
  13. Find the law of the influence from the injection pressure to the filling time and the cavity pressure and make certain of the best filling time, injection time and injection pressure. though the analysis of the flowing velocity and pressure spread of the key position element in the injection parts in different gate position, we forecast the injection parts quality and the possibility injection flaw and its position, optimize the gate position. in this paper, though the research of analogue of the runner system of metal - powder injection molding and the process of injection molding, we get the law of how the injection parameter influence the injection process

    在相同的注射條件下，通過分析喂料在不同直徑和長度流道中的流動規律，得到了喂料在流道中的速度場、壓力場和溫度場，找到了流道長徑比的合理取值范圍，並得出通過改變流道設計可實現對現有設備資源充分利用的結論；給出了不同注射壓力下，型腔壓力與充模時間關系曲線和喂料熔體平均充填速度與充模時間關系的曲線，得到了注射壓力對充填時間和型腔壓力的影響規律，確定了最佳的充模時間、注射時間和注射壓力；通過分析採用不同位置澆口注射時注射件關鍵位置單元的流動速度和壓力分佈，預測了注射件的成形質量，或可能產生的注射缺陷及位置，優化了澆口設置。
  14. This curvature of the flow field alters the pressure distribution and the aerodynamic forces from their values in translational flight.

    流場的彎曲使壓力分佈和空氣動力與直線飛行時的值相比發生了變化。
  15. This paper presents a type of electroplate production - line system which drives by linear induce motors and describe the entire control system the new system is controlled by digital signal processing chip ( dsp )

    論文結合中山寶泰電路板設備製造有限公司的電鍍流水線系統而開展地課題研究設計工作，研究了一套直線感應電機驅動的電鍍流水線及控制系統。
  16. Under windows nt and labview development environment, using the linear fit module, exponential fit module > general polynomial fit module of labview to design a method for fitting the experiment data, the results of curve fitting indicate that the purpose of general polynomial fitting is better than the rest. separating the equivalent input impedance of magnetostrictive transducers without stimulate current from input impedance of it with stimulate loop based on the results of curve fitting, and determining the syntony frequency and electric simulation network parameters of magnetostrictive transducers by this input impedance. finally, with labview network functions, realizing magnetostrictive transducer electric simulation system based on web server and discussing a scheme for this system network by datasocket. the method of this paper can more accurately determine the syntony frequency and electric simulation network parameters of magnetostrictive transducers than the testing method of syntony & anti - syntony. at the same time, discussing virtual instrument measurement system and how to realize magnetostrictive transducer electric simulation network system by labview network functions of network virtual instrument measurement development environment

    在windowsnt系統環境和labview虛擬儀器技術開發平臺下，首次利用labview中的直線擬合模塊、指數擬合模塊以及多項式擬合模塊，設計了一種對實驗所得數據進行曲線擬合的方法，對三種擬合方法進行了比較，曲線擬合結果表明，多項式擬合方法相對于其它兩種擬合方法效果更好；根據曲線擬合的結果可從帶激勵線圈的磁致伸縮換能器的輸入阻抗中分離出磁致伸縮換能器鐵芯在無激勵電流時機械振動形成的等效輸入阻抗，並由此輸入阻抗確定了磁致伸縮換能器的諧振頻率及其電氣模擬網路參數；最後通過labview提供的網路功能，實現了基於web服務器的磁致伸縮換能器電氣模擬虛擬儀器測試系統，並探討了通過datasocket技術實現該系統網路化的方案。
  17. Based on above views, by analyzing power structure and building power system theory model, many important summations have been made which they followed : the texture of fdi is an none liner, many circle - roads and complex giant system which is made up by economics factors, political factors, systematic factors and the investors " psychological factors

    以上述觀點為基礎，通過分析動力結構，建立國際直接投資動力機制理論模型，得出如下重要結論：國際直接投資地域結構是由經濟因素、政治因素、體制因素以及決策者的心理因素等共同作用下國際生產資本跨國流動動所形成的非線性、多迴路的復雜巨系統。
  18. Research on adaptive damper system review the current er damper and active vibration control technology, the conception of converting vibration energy to energy damping vibration is presented. the adaptive er damper system has a rack and pinion mechanism which converts a linear motion of piston to a rotary motion

    採用齒輪、齒條機構將車輛的往復直線運動變換為旋轉運動，再利用齒輪機構升高轉速驅動永磁直流發電機產生電能，把電壓升高後作用於電流變流體減振器，由此構成一個完整的自適應減振器系統。
  19. ( 7 ) the warships bearings - only passive location system and its engineering implement is researched, the operation flow and methods of over - the - horizon concealed missile attack using single and multi - warship bearings - only passive location system is presented. the direction finding data calibration and pretreatment based on uniform speed straight movement are also studied

    7進行了艦艇純方位無源定位系統及其工程實現方法的研究，給出了應用單艦和多艦純方位無源定位系統引導反艦導彈實施超視距隱蔽攻擊的方法和作戰流程，研究了基於勻速直線運動的測向數據校準處理方法和測向方位角數據的預處理方法。
  20. The machine uses the straight line movement bearing. causes the machine movement to be smoother

    機器採用直線運動軸承。使機器運行更流暢。
分享友人
分享到 Line

分享到臉書