直錐 的英文怎麼說

中文拼音 [zhízhuī]
直錐 英文
right circular cone
  • 直 : Ⅰ形容詞1 （成直線的; 硬挺的） straight; stiff 2 （跟地面垂直的; 從上到下的; 從前到后的） erect; v...
  • 錐 : Ⅰ名詞1. （錐子） awl2. （似錐物） awl-shaped things 3. （錐體） cone Ⅱ動詞（鉆） drill; bore
  1. Ring's diameter increases as we move away from the apex of the cone.

    諸圓環的直徑自圓錐頂逐漸增大。
  2. The rocket climbs upward and onward, with an artificial satellite cradled in its nose cone.

    隨帶裝在其前端錐形體內的一顆人造衛星，火箭一直向上，向前爬升。
  3. Adopting the straight - line bearing and asynchronism electrical machineries of conical surface braking, operation is steady

    採用直線軸承及錐面制動三相異步電機，運作平穩。
  4. Basic tooth profile of straight and skew bevel gears

    直齒及斜齒錐齒輪基本齒廓
  5. Study on gear tooth surface of generating spur bevel gear

    滾齒直齒圓錐齒輪齒形的研究
  6. Main products include suited offset point imprinter bearing sets comber gear for weaving industry metal mould and gear vacuum gear synchro gear worm worm wheel. acme whorl fitting and all kinds of fittings with various gears

    主要產品：印刷行業各種膠印機和印后設備輪及軸承套，紡織行業精梳機輪，金屬板材壓延模具和輪，真空泵輪同步帶輪蝸桿蝸輪副acme螺紋副各種直斜錐及各種盤類和軸類件等機械加工件。
  7. The demonstration of the conic section is an envelope of family of straight lines

    圓錐曲線是直線族的包絡的證明
  8. On the uniform equation of conic section in descartes coordinate system

    直角坐標系下圓錐曲線的統一方程及變化動態初探
  9. Straight bevel gears for general engineering and heavy engineering part 2 : modules and diametral pitches

    一般和重型機械用直齒錐齒輪.第2部分:模數和齒距
  10. Taper pins, dowel pins, straight pins, grooved pins, and spring pins inch series

    錐形銷定位銷直銷槽銷和彈簧銷
  11. Magnetos and dynamos for motorcycles

    摩托車磁發電機和直流發電機.錐軸端
  12. On the base of resemble model, the figure of contracting pipe was changed, the generatrix became arc for once it was straight line, named resemble model

    在相似模型的基礎上，收縮管的直線圓錐改造成母線為圓弧形的圓錐，稱相似模型。
  13. The beyond is the simple notation of serial number of pricker, totaled 7 digits of codes, in which the first digit represents the diameter of needle - bar of pricker, the second digit represents the siding of triangle side on functional section of pricker, the third digit represent the length of functional section of pricker, whereas in standard notation, it represents the distance from needlepoint to gradual deflating small port ( lower port ), the fourth digit represents the total length of pricker, which is the distance from the inside of bending helve to the needlepoint, the fifth digit represents the total quantity of dents on the cording of functional section, and the sixth digit represents the model of barb on functional section, while the seventh digit represents the distance between barbs on functional section

    以上為刺針編號的簡單寫法，共7位代碼，第一位是刺針針桿的直徑；第二位是刺針工作段三角面的邊寬；第三位是刺針工作段的長度，同標準寫法所不一樣的是針尖到漸縮錐小口（下口）的距離；第四位是刺針的總長度，按彎柄內側至針尖的距離；第五位是工作段棱上的總齒數；第六位是工作段上鉤刺的型號；第七位是工作段上鉤刺與鉤刺之間的距離。
  14. Some properties on rectilinear generators of hyperboloid of one sheet are researched. the relation between rectilinear generators of hyperboloid of one sheet and its asymptotic cone are discussed

    摘要給出並證明?單葉雙曲面的直母線的若干性質，討論了單葉雙曲面與其漸近錐面的直母線之間的關系。
  15. Parallel shank jobber and stub series drills and morse taper shank drills

    直柄機用短型系列鉆頭和莫氏錐柄鉆頭
  16. All the larvae are straight, with a slight taper towards the rear.

    所有幼蟲都是直形背部略帶錐形。
  17. The directrixes of the in former two transmissions are the loxodrome and the geodesic on the pitch cones, that of the latter is an equal - pitch line along the direction of straight generatrixes in the hyperboloid surface, also is the vertical trajectory of the straight generatrixes

    前兩種傳動形式的準線分別為節錐面上的斜航線與測地線，後者的準線為單葉雙曲面上沿直母線方向的等螺距曲線，且為直母線族的正交軌線。
  18. Morse and metric taper reamers with parallel shanks

    直柄莫氏圓錐和公制圓錐鉸刀
  19. It consists of a vertical, tapered glass tube containing a movable weight.

    它在垂直的錐形的玻璃管內裝一個可以活動的重物。
  20. The study for transforming property of right cone fiber

    直錐形光纖傳輸性質的研究
分享友人
分享到 Line

分享到臉書