相對曲率半徑 的英文怎麼說

中文拼音 [xiāngduìqūlǜbànjìng]
相對曲率半徑 英文
relative radius of curvature
  • 相 : 相Ⅰ名詞1 （相貌; 外貌） looks; appearance 2 （坐、立等的姿態） bearing; posture 3 [物理學] （相位...
  • 對 : Ⅰ動詞1 （回答） answer; reply 2 （對待; 對付） treat; cope with; counter 3 （朝; 向; 面對） be tr...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 半 : Ⅰ數詞1 （二分之一） half 2 （在 中間的） in the middle; halfway 3 （比喻很少） very little; the l...
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 相對 : 1. （面對面） opposite; face to face 2. （非絕對的） relative 3. （比較的） relatively; comparatively
  1. Based on the diopter status of myopia and hypermetropia, the paper presented the principle of excimer laser refractive surgery, the change of impacting cornea curvature on the cornea diopter. in this chapter, we also discussed excimer laser - corneal tissue interactions and photoablation. determine the relationship between the fluence of arf excimer laser and the cornea ablation rate, attain the relationship between the energy density and the ablation depth

    研究了激光與生物組織相互作用、光蝕作用及準分子激光消融角膜的機理；首次定量研究193nm準分子激光高斯光束的切削量與能量密度的關系，計算單個激光脈沖角膜切削量；發現了角膜曲率對切削效果的影響，首次提出了角膜曲率半徑、切削位置與切削深度的關系；首次定量確定了激光光斑參數及其排列方式對術后角膜表面粗糙度的影響，為更精確實現角膜切削和提高切削后角膜表面光潔度、減少手術后角膜渾濁及角膜表面術后不規則提供了理論依據。
  2. Relative radius of curvature

    相對曲率半徑
  3. 3 ) the combination of alike corners, radiuses and bottoms with different border coefficients. 4 ) the contrast between the conditions with exit incline ridge and the one without it. 5 ) the contrast between the conditions with entrance ridge and the one without it

    L ）不同轉角，曲率半徑和底坡組合; 2 ）相同轉角和曲率半徑，不同底坡的組合; 3 ）才目同轉角，曲率半徑和底坡，不同邊坡系數的組合; 4 ）有無出口斜坎的對比; 5 ）有無進口坎的對比; 6 ）不同坎高的對比。
  4. All this has laid a strong foundation for selecting a subject of maskless afm nanolithography, i. e., field - induced oxidation of si semiconductor. in chapter two, a high - intensity current between a probe tip and a sample is discussed first. electrical intensity between them is simulated using matlab software after an electrical model is introduced, thus theoretically analyzing the effect of tip radii, tip - sample separation, radii at the sample, and biases on the morphology of field - induced oxidation

    第二章首先討論了掃描探針與樣品之間的高密度電流，得出了電流密度與偏置電壓和探針?樣品間距密切相關，其關系不能以簡單的線性或指數函數來表述的結論；然後引進了掃描探針場致加工的電場模型，利用matlab模擬探針與樣品之間的電場強度，分析了掃描探針加工條件包括探針針尖曲率半徑、探針-樣品間距、樣品平面半徑以及偏置電壓等對場致氧化物幾何形態的影響。
  5. Its reliability has been tested though examining. the influence laws of mould structure, including wiper die and the style, size and installed position of mandrel, have been studied. combined with the theoretical analysis of perfect pure bending, the tendency of relative bending radius r / d and relative wall thickness t / d to one of the major quality target - the maximum wall thickness reduction ratio is also studied

    通過數值模擬研究獲得了包括防皺塊和芯棒形式、尺寸和安裝位置在內的模具結構對製件成形質量的影響規律；結合對理想純彎曲的理論分析，研究獲得了相對彎曲半徑r / d 、相對壁厚t / d對製件主要質量指標之一的最大壁厚減薄率的影響趨勢和大小。
  6. We designed two kinds of diameter s - shaped curved arteries finite element numerical simulation geometric models in order to study the influence caused by the singular curved factor ( such as the curvature radius, the dean number ) to flow, and extract the characteristic flow form related to the curve

    在總結和發展前人成果的基礎上，設計了兩種直徑的s型彎曲動脈有限元數值模擬幾何模型，以考察單一的彎曲因素（曲率半徑、 dean數等）對流動的影響，以提取與彎曲相應的特徵流型。
分享友人
分享到 Line

分享到臉書