研磨曲線 的英文怎麼說

中文拼音 [yánmóqūxiàn]
研磨曲線 英文
milled-in current
  • 研 : 研同 「硯」
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 研磨 : 1. （用工具研成粉末） grind; pestle2. （用磨料摩擦器物使變得光潔） abrade; polish
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. The effect of borided layer at low temperature on wear resistance and brittleness of borided layer for steel 45 was studied by means of wear test, brittleness test and anode polarization measurement

    通過磨損試驗、脆性試驗和陽極極化曲線的測試，研究了低溫滲硼對鋼滲硼層耐磨性、脆性和耐蝕性的影響。
  2. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  3. The image of the curve is obtained by planar ccd system. the author independently works on : ( 1 ) the image processing : ( 2 ) the imaging model of the ccd cameras, that is the coordinate transforming relationship between the image coordinates and the corresponding world coordinates : ( 3 ) the method of curve connection : ( 4 ) the experiments of the figures of the wheel trackside profile and calculation of the flange thickness related to the wheel wear

    作者獨立完成的工作包括： （ 1 ）對車輪輪廓的激光曲線圖象進行處理； （ 2 ）建立了左、右ccd攝像機的實際攝像模型，推導出圖象坐標到物方實際坐標的變換關系； （ 3 ）研究了幾種曲線拼接方法； （ 4 ）通過實驗，應用曲線拼接方法確定輪廓曲線的形狀，最終算出反映車輪磨損的重要參數。
  4. At first, based on current situation of china ' s trunk railway lines and the features of passenger and freight traffic, this paper points out that regarding the rail side wear of the curves have realistic significance for china ' s railway

    本文首先從我國路網干線的現狀、客貨運輸的特點，指出了減緩曲線鋼軌側磨對於我國鐵路具有的現實意義，同時介紹了國內外關于輪軌磨耗研究的發展現狀。
  5. The cross short rollers guide way and servo feed - system are the most important parts of 3mz204cnc bearing internal grinding machine made by luoyany bearing research institute. - we have analysised firstly the factor of influence with roller guide way rigid, and we have obtained a load - distortion curve. we also have analysised the dominating factors influence with distinguish ratio of guide way, and we have obtained a solution about pre - tighted load which were tested by experiments

    本文對洛陽軸承研究所研製的3mz204cnc全自動內圓磨床的核心部件：十字交叉滾子導軌和數控進給系統展開研究，首先對影響滾動導軌剛度的因素進行分析，得出載荷?變形曲線，對影響導軌解析度的各因素進行分析，得出預緊力大小與分佈對解析度和起動力的影響，並通過實驗驗證。
  6. Iges and step standard format and the sat format which is used in acis has been studied. according to the characters of different parts and the characters of different machine tools, a method of grinding for non - circular surface is researched, a new strategy and algorithm of non - circluar surface nc griding which based on acis is studied. a way of non - circluar surface internal grinding is realized as well as the way of non - circluar surface external grinding

    論文的研究包括了以下幾個方面:研究了三維幾何造型引擎acis平臺及其拓撲結構，探討了iges和step等產品數據交換標準格式和acis中的sat文件格式的異同;根據零件的加工特徵和機床的結構特點，研究了在內圓磨削和外圓磨削方式下，非圓曲面磨削的數控編程技術;提出了基於acis實體造型的任意非圓曲面零件的數控磨削新演算法;實現了以實體造型為基礎的任意非圓曲面零件的內圓和外圓數控磨削;根據零件的特徵和磨削方式，生成了相應的走刀路線;實現了針對不同機床的後置處理。
分享友人
分享到 Line

分享到臉書