研磨砂粒度 的英文怎麼說
中文拼音 [yánmóshālìdù]
研磨砂粒度
英文
grit-
Abstract : the effect factors of grinding roller surface roughness areanalyzed and experimented. the law of effect factors such as roller rotary speed, grinding wheel granularity, grinding liquid and so on, about roller surface roughness is obtained. the mathematical model of roughness is established through regression
文摘:對影響磨削輥面粗糙度的因素進行了系統分析和實驗研究，得出了軋輥轉速、砂輪速度、砂輪粒度、磨削液等因素對磨削輥面粗糙度影響的一般規律，利用回歸分析的方法建立了粗糙度的數學模型。Erosive resistance of grey cast iron matrix composite has been investigated, on the condition of different volume fraction of wc and erosive angles and volume fraction of. the results showed that, the erosive resistance of composite with volume fraction of 27 wt % was the best ; volume abrasion rate of composites with different erosive angles was maximum at 50 angle, but volume abrasion rate was less at 0 and 70 angle ; on condition of the same volume fraction of wc and larger size of quartz sand in slurry, volume abrasion rate increased
結果表明：碳化鎢體積分數為27的灰鐵基復合材料的耐沖蝕磨損性能最佳；不同沖蝕角下復合材料的體積碳化鎢顆粒增強鐵基表面復合材料及其沖蝕磨損性能研究摘要磨損量在50 「沖蝕角處最大，在0 」和70 」沖蝕角處較小；在碳化鎢顆粒體積分數相同的情況下，當漿料中的石英砂粒度大時，其體積磨損量增大。The results show that, when increasing the feed rate of the grinding wheel, decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel, the material removal rate in the wafer rotating grinding increase, the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel, decreasing the feed rate of the grinding wheel and using finer grit grinding wheel, the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ), beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000, the material removal rate decreases and the wafer surface roughness has no obvious improvement
研究結果表明，增大砂輪軸向進給速度和減小工件轉速，採用粗粒度砂輪有利於提高磨削矽片的材料去除率，砂輪軸向進給速度對材料去除率的影響最為顯著；適當增大砂輪轉速，減小砂輪軸向進給速度，採用細粒度砂輪可以減小磨削表面粗糙度；在其它條件一定的情況下，砂輪速度超過一定值會導致材料去除率減小，主軸電機電流急劇增大，表面粗糙度變差；採用比# 2000粒度更細的砂輪磨削時，材料去除率減小，矽片表面粗糙度沒有明顯改善。By using a wafer - rotating grinding machine, the influence of the main process factors including grit size of diamond grinding wheel, rotating speed of the wafer chuck table, rotating speed and the down feed rate of the cup grinding wheel on the material removal rate, spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated
摘要利用基於自旋轉磨削原理的矽片超精密磨床，通過試驗研究了砂輪粒度、砂輪轉速、工件轉速及砂輪進給速度等主要因素對材料去除率、砂輪主軸電機電流以及磨削后矽片表面粗糙度的影響關系。Testing method for grain size of coated abrasive macrogrits p12 - p220
砂布用研磨材料粗晶粒的粒度試驗方法Polished with abrasive belt of grit # 150 - 320 on the no. 4 finish and has continuous streaks, mainly used as build ing ? ornaments, elevators, door of building, frontal plate etc
4經適當粒度拋光砂帶的連續研磨生成研磨花紋的產品（細分150 - 320號） 。主要用於建築裝飾，電梯，建築物的門、面板等。分享友人