硬化深度 的英文怎麼說

中文拼音 [yìnghuàshēndù]
硬化深度 英文
case depth
  • 硬 : 形容詞1 （堅硬） hard; stiff; tough 2 （剛強; 堅定; 強硬） strong; firm; tough; obstinate 3 （勉...
  • 深 : Ⅰ形容詞1 （從上到下或從外到里的距離大） deep 2 （深奧） difficult; profound 3 （深刻; 深入） thor...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 硬化 : 1 （變硬） harden; stiffen; stiffening; indurascent; ossification; cure; curing 2 [醫學] （組織變...
  • 深度 : 1. （深淺程度） degree of depth; depth 2. （觸及事物本質的程度） profundity; depth
  1. It contains unsatu - rated fatty acid dha & epa, helps to balance the blood lipid levels, debase cholesterol, prevent cruor, cerebral hemorrhage, cerebral thrombus and senile dementia, etc

    深海魚油俗稱「降脂靈」 ，能有效降低膽固醇和甘油三酯的含量，從而降低血液粘稠度，促進血液循環及消除疲勞，預防動脈粥樣硬化、腦溢血、腦血栓和老年癡呆，並可緩和痛風及風濕性關節炎。
  2. Comparison tests were made to the primary and secondory detonations and the same quantities of the same explosives, and found that both the surface rigidity and the depth of the induration layer have been improved obviously by the use of secondary detonation

    同時對同種炸藥相同藥量分兩次爆炸與一次爆炸的效果進行比較，發現採用二次爆炸要比一次爆炸無論表面硬度，還是硬化層深度都有明顯改進。
  3. Methods of measuring case depth for steel hardened by flame or induction hardening process

    鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法
  4. Steel products. determination of the effective depth of hardening after flame or induction hardening

    鋼產品.表面或感應淬火后硬化有效深度的測定
  5. On the premise that the basal transducer layout was designed according to the requirements of deep - sea exploring surroundings and technology on the basis of the hardware structure and data collecting ways of interferometric sonar, the echo signal by energy relativity search is analyzed and calculated, altitude data of the tiny terrain on the seabed under real - time irradiation of ultrasonic is gained as to provide parameters of best cutting depth for intellectualization of the seabed mining vehicle timely and promptly

    摘要在相干聲納硬體結構及數據採集方式的基礎上，結合具體的深海鈷結殼探測環境和技術要求，確定了換能器基本布局，探討了信號採集與處理方法，利用能量相關搜索法對回波信號進行分析和計算，得出超聲波實時照射下的海底表面微地形高程數據，為海底采礦車智能化開采提供實時、快速的最佳切削深度參數。
  6. Measuring case depth for steel

    鋼表層硬化深度測定法
  7. Numerical simulation of hardened - depth on eddy signal

    渦流場量評價材料表面硬化層深度的數值模擬
  8. Nondestructive testing and quality control of metal hardened - depth is an important problem to be solved in machinery industry. it belongs to material property testing

    金屬表面硬化層深度的檢測及控制是目前機械工業部門急需解決的一個問題，它屬于材料檢測的范疇。
  9. We also have outstanding talented experts in china, which form a software base to produce high - quality piston rings. anqing diamond pays a special attention to its nit riding, and the nitride piston rings have been highly honoured for its features. namely high modulus of elasticity, heat - resisting, wear - resisting etc

    值得一提的是，帝邁德擁有卓越超群的氣體氮化加工工藝，使帝邁德氮化環的各項性能指標彈性模數熱穩定性耐拉缸性氮化層硬度深度和脆性等獲得國際同行界的高度評價，達到國際領先水平。
  10. Hardness depth of heat - treated parts ; determination of the effective depth of hardening after nitriding

    熱處理件的硬化深度.氮化處理后硬化有效深度的測定
  11. Testing hardened concrete - part 8 : depth of penetration of water under pressure ; german version en 12390 - 8 : 2000

    硬化混凝土試驗.第8部分:加壓水滲透深度
  12. Determination of effective depth of hardening after induction or flame hardening of steel

    鋼的感應淬火或火焰淬火後有效硬化層深度的測定
  13. Iron and steel - determination of the conventional depth of hardening after surface heating

    鐵和鋼.表面加熱后常規硬化深度的測定
  14. Testing hardened concrete - depth of penetration of water under pressure

    硬化混凝土試驗.加壓時水的滲透深度
  15. Testing hardened concrete - part 8 : depth of penetration of water under pressure

    硬化混凝土試驗.第8部分:加壓時水的滲透深度
  16. Steels - determination and verification of the depth of carburized and hardened cases

    鋼件滲碳淬火硬化層深度的測定和校核
  17. In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment

    第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。
  18. Iron and steel. determination using fracture test pieces of the austenitic grain growth tendency and of the hardness depth in tool steels shepherd test

    鋼鐵.用斷裂試驗樣件對奧氏體晶粒增長傾向和對工具鋼硬化深度的測定
  19. Effective case depth

    有效硬化深度
  20. Hardness depth of heat - treated parts - part 4 : determination of the fusion hardening depth and the fusion depth

    熱處理零件的硬化深度.第4部分:熔煉硬化深度和熔煉深
分享友人
分享到 Line

分享到臉書