碎斷剪 的英文怎麼說
中文拼音 [suìduànjiǎn]
碎斷剪
英文
chopping shear-
Three stages of deformation can be distinguished from the cataclastic superposition of matrices that infilled the microcracks in cataclastic rocks, and two phas es of paleotectonic stress field from the typical conjugated shear joints by stereograms illustrating
構造巖中膠結物和微裂隙充填脈反映了巖石碎裂變形的三次疊加。斷裂變形帶內發育兩期典型的共軛剪節理，但區域分佈各有特點，反映出斷裂變形的空間演化。The fault controlled the magmatism and metallization relevant to the contact zone, and deformed successively and produced cataclastic rocks and two sets of joints ; the second stage was from late cretaceous to eocene. the fault zone deformed right - laterally under ne - sw striking transtention, and new joints zone was produced at the end of the two main faults because of local stress concentration. the fault produced inchoative cataclastic rocks, and two sets of typical joints in plutons ; the third stage of deformation was relatively faint and only a little of microcracks was produced and infilled with vei ns in the deformed rocks, which was during the himalayan movement
其後的繼承性活動在斷裂帶內形成碎裂程度最強達到碎裂巖的碎裂巖系列構造巖，變形帶兩側發育兩組典型的共軛剪節理；第二次在晚白堊世?始新世，斷裂在北東?南西向近水平擠壓作用下右行張扭性活動，斷裂帶兩主斷裂在斜列重疊的端部由於局部應力集中進一步擴展形成節理帶，而斷裂在巖體區也發育兩組典型的共軛剪節理，斷裂內形成初碎裂巖為主的構造巖；第三次是喜山期以西側抬升、東側下降的強烈升降為主的活動，在基巖中，主斷層兩側圍巖出現微破裂。Em, like resistivity, can also give structural information: faults, shear or altered conductive areas.
和電阻率法一樣，EM法也能提供構造方面的資料，如斷層、剪碎帶或蝕變導電帶。The dynamo runs at rull speed to drive main shaft, then the main shaft makes the emulsifying wings in emulsification grove rotate, which absorbs the liquid in its brand groove into ring groove through guide vanes on upper and lower sides of the groove. the vanes spins circularly at high speed with the main shatf as center, and the blade and emulsificaton groove cut and crush it continuously. after that. it gers squeezed by the vanes highspeed centrifugal rotation. at last, it finishes isotropt emulsification tratment within extremely short time after continuous circulating mixing
由電動機全速運轉帶動主軸，經主軸轉動乳化框槽內之乳化翼片，使其將桶槽內之液體經框槽上、下兩側之導流葉片吸入環狀框槽內，經以主軸為中心高速圓周旋轉葉片；連續使乳化翼端刀面與乳化框間極小之間系高頻率之強力切割剪斷、粉碎，再借葉片高速離心旋轉排擠，持續循環混合，以極短之時間即可完成均質乳化之處理。The stirred fluid and beads have multidimensional circulation motion and self - rotation for the stirrer rotation in the grinding chamber of a stirred media mill. high intensity motion is caused by multi - direction displacement of fluid and beads. the powder is comminuted by compression caused by beads gravity and helical turn for rubbing, impacting and shearing
攪拌磨磨筒中，在攪拌器的攪動下，物料與磨介作多維循環運動和自轉運動，從而在磨筒中不斷地上下、左右相互置換位置產生激烈的運動，由磨介重力以及螺旋迴轉產生的擠壓力對物料進行摩擦、沖擊、剪切作用而粉碎。A solid - state shear compounding technology based on pan - milling ( s3c ) has established, by which the graphite with weakly combined structure are exfoliated and then compounded with pp at nanoscale. the obtained pp / graphite nanocomposites have greatly enhanced electrical and thermal conductivity. their structures and properties were characterized by analysis of particle size and distribution, sem, tem, xrd, the electrical conductivity, the thermal conductivity and heat - decomposition temperature etc. by taking advantages of the layered inorganic fillers with a weak interaction between layers ( e. g
磨盤碾磨剪切力場使pp分子鏈斷裂，相對分子質量減小，石墨的導熱和潤滑性能抑制pp的降解和粉碎，使pp / yep250 （膨脹石墨250倍）復合粉磨盤碾磨固相剪切復合技術及導電導熱pp /石墨納米復合材料的制備與性能體中， pp分子運動活性提高，結晶能力增強，為pp在熔融加工中進一步向己剝離的石墨片層間擴散，形成納米復合結構創造了條件。Em, like resistivity, can also give structural information : faults, shear or altered conductive areas
和電阻率法一樣， em法也能提供構造方面的資料，如斷層、剪碎帶或蝕變導電帶。分享友人