碎粒研磨 的英文怎麼說
中文拼音 [suìlìyánmó]
碎粒研磨
英文
sizing reduction-
The crystalline structure changes of pp induced by pan - milling were characterized by x - ray diffraction and raman spectroscopy. xrd analyses show that when pp was co - milled with uhmwpe, crystal transformation of pp occurred, its crystallinity and crystallite size decreased, whereas, only slight reduction of crystallinity and crystallite size were observed and no crystal transformation was found when pp was co - milled with wtr chips, and amorphization of pp was strongly enhanced by co - milling pp with iron
採用x -射線衍射研究了聚丙烯碾磨粉碎過程微觀結構變化， uhmwpe存在下pp發生晶型轉變、結晶度降低和晶粒尺寸減小；彈性材料wtr抑制pp塑性變形，碾磨導致分子堆積有序區域膨脹，晶面間距增大，結晶度下降；剛性材料金屬鐵與pp產生強烈摩擦，加快晶粒細化，晶格破裂導致非晶化。The character of tube roll mill is that it combines the advantages of ball mill and roller, then great improves the grinding efficiency through the study of the grinding theory of tube roll mill, pressing stress, grinding effect and the comparation between roller and vertical mill, this text combined the national important technology equipment crert item - - tube roll milling developing item, gets following results : firstly, because of the special structure of tube and roll, powder from single particle grinding in the early peried contincely transit press grinding stage, it better stops the loss of splash energy, secondly, during the grinding progress, powder form loose to dense fully uses the nonsmoth surface of particle and stress focus to make its stress lower than roller " s
本文結合國家重大技術裝備國產化創新項目-筒式輥碾磨開發項目，通過對筒輥磨的粉磨機理、層壓應力的分析、粉磨效果的研究及與輥壓機、立磨粉磨效果、粉磨機理的比較，可知：首先，由於筒與輥的特殊結構方式，筒輥磨內粉體由初期的單顆粒破碎逐漸過渡到層壓粉碎階段，較好地防止了飛濺能的損失，其次，在粉磨過層中，粉體由疏鬆到密實，充分利用了顆粒的非光滑表面及應力集中效應使其應力低於輥壓機。實驗證實，筒輥磨的粉磨效果大大優于立磨和輥壓機。This edta route has several remarkable advantages in comparison with other method. because of the greater ability of edta anions to chelate metal cations, and forming very stable and soluble complexes, all of the starting materials are mixed at the molecular or atoms level in a solution, it is easy to control the composition and a high degree of homogeneity is achievable
傳統的合成方法是高溫固相反應，由於灼燒溫度高、灼燒時間長，形成硬團聚體，產物粒徑較大，一般為m級，需進行球磨粉碎以減少其粒徑，很難制得均相、均一粒度分佈的氧化物粉體，在研磨過程中容易引入雜質且晶形破壞使得發光亮度減小。The crystal pvc was crashed by jet - mill to prepare nanocrystal pvc. the crash, degradation and the change of morphology and crystalline structure changes of pvc was studied by ftir, sem, dsc, tem
用氣流磨對結晶pvc進行粉碎，制備了納米晶pvc ，研究了在高速氣流作用下pvc的破碎降解、顆粒形態和微晶結構變化。The crystal pvc is crashed by jet - mill to prepare nanocrystal pvc. the crash, degradation and the change of morphology and crystalline structure changes of pvc is studied by ftir, sem, dsc, tem. the self - plasticization of nanocrystal pvc is studied, too
用氣流磨對結晶pvc進行粉碎，制備了納米晶pvc ，研究了在高速氣流作用下pvc的破碎降解、顆粒形態和微晶結構變化，研究了納米晶pvc對pvc的增塑作用。分享友人