碳鐘 的英文怎麼說
中文拼音 [tànzhōng]
碳鐘
英文
carbon clock-
Water, containing dissolved calcium hydrogen carbonate, passes through the limestone and drops evaporate on the stalactite, increasing its length with a deposit of calcium carbonate.
含有溶解碳酸氫鈣的水通過石灰石滴在鐘乳石上蒸發，隨著碳酸鈣沉積物的增加不斷增加著它的長度。A lot of chemical article, like lysol, fluid of limewater, carbonic acid, hydrogen peroxide solution, iodine, alcohol, 84 disinfection is waited a moment, all can kill n / med tuberculosis bacili, what need time to differ nevertheless, some needs a few minutes, some needs a few hours
許多化學物品，如來蘇兒、石灰水、碳酸、雙氧水、碘酒、酒精、 84消毒液等等，均能將結核桿菌殺死，不過所需時間不同，有的需要幾分鐘，有的需要幾小時。Slow down printing speed can take more time for toner transfer, avoid paper jam and increase color saturation. in the market, there are different types such as 4 5 ppm pages per minute, 16 ppm and over 20 ppm. fortunately, printing speed is possible to be controlled by selection icon of paper material
降低列印速度的目的是讓碳粉有充份的時間移轉至紙張上藉以增加色彩飽和度同時可以避免卡紙發生，目前在市場上可以看到每分鐘列印4 5頁16頁及20頁以上等不同機型印表機，幸好可以使用挑選紙張材質的選項來控制列印速度，建議列印速度在106 163 gsm 。The company is specialized in producing of mesh - belt continuous sintering furnace 、 pusher - type high temperature sintering furnace 、 steel - belt iron powder refining reduction furnace （ electric - heating rbo furnace and direct gas - burning heating rbo furnace are also produced ） 、 pressure bell type furnace 、 carburizing quench furnace and some kinds of accessorial equipments
目前生產項目有：網帶式連續燒結爐、推桿式高溫燒結爐、蒸汽處理爐、鋼帶式鐵粉還原爐（電加熱、氣體燃燒直接加熱rbo型均生產） 、加壓鐘罩爐、滲碳淬火爐及各種輔助設備。Rapid heating rate and no decarburized zone due to heat treatment during austenization, the staying time between 850 to 1000 is only 5 to 10 second, thus no decarburized zone can be formed
在加熱奧氏體化過程中，在850 - 1000溫度范圍內的停留時間只有5 - 10秒鐘，因此，不會有熱處理脫碳層。Sintering speed increased greatly with the help of great quantity of heat of the molten iron, the great quantity of heat sent out from the carbonizing reaction and a little quantity of liquid, this sintering type is an instantaneous sintering, the sintering compacting can carry completely in a few minutes, the degree of sintering compacting is very high. ( 6 ) the vc - fe surface composite has high rigidity, it ' s rigidity exceeds 60hrc, under condition of dry sliding friction and overloading
鑄造燒結時，過熱鐵水的巨大熱流密度沖擊、粉料壓坯中的碳化反應的放熱以及壓坯中少量液相的產生使壓坯的燒結速度大大提高，此時屬瞬間液相燒結，在十幾分鐘內燒結過程即可完成，可達到很高的緻密化程度。 （ 6 ）鑄態下vc一fe表面復合材料具有很高的硬度，其鑄態硬度） 60hrc 。Pentaco, spol. s r. o. - the delivery program covers material, retail and chipboards as well as clocks and coal
是一家高級企業，該企業針對客戶需求製造專門的晶元板，時鐘，煤、碳，細分、細節，材料。A new purified method for carbon nanotube was put forward. 2. study of aligned multi - wall carbon nanotube layered multi - wall carbon nanotube arrays were synthesized firstly directly on the surrounding of the reaction quartz tube, in a ar / h2 atmosphere by pyrolysis of ferrocene in xylene into a suitable reaction furnace with cobalt powder in
與根據碳納米管的物理、化學性質，提出了一種全新的碳納米管純化方法：先對制備的碳納米管於500在空氣中氧化30分鐘，然後用18的鹽酸煮20分鐘，最後將樣品稀釋，過濾，再用去離子水過濾3次，烘乾，便可得到純的碳納米管。But every minute of flying time saved can reduce fuel consumption by some 60 litres and cut 160kg of co2 emissions, so the effort is well worthwhile
但每節約一分鐘的飛行時間，可以減少大約60升的燃料消耗和削減160公斤的二氧化碳排放量，所以，努力還是值得的。Once water starts to flow out of the faucet, allow the system to run for 5 minutes to flush our any harmless carbon fines that may be present
一旦水開始從水龍頭流出后，使系統運行5分鐘，以沖出可能含有的無害碳粒子。The speed became fast at the temperature 1050. the reaction could carry completely when billets was kept in vacuum tube for 3 hours " at 1050 temperature, under the striking of great quantity of heat when the molten iron poured into the mold, the reaction was blazed rapidly and continued at a high speed. the diffusible speed of v and c was very fast because the billet was heated over 1300 in a moment, so the reaction ca n complete in a few minutes
（ 5 ）碳化反應v + c vc在900左右開始發生，此時是固相反應，反應速度較慢，反應不能進行完全，隨溫度升高，該碳化反應的速度加快，在1050保溫3小時可以進行完全，在鑄造燒結時在過熱鐵水的巨大熱流密度沖擊下， v + c vc立即被激發，並以很快的速度進行，由於坯塊被加熱到1300以上，此時c和v擴散速度很快，因此鑄造澆注后的幾四川大學碩士學位論文分鐘內反應可以進行完全。分享友人