磁隙中心 的英文怎麼說
中文拼音 [cíxìzhōngxīn]
磁隙中心
英文
magnetic centre of gap-
The axial magnetic field distribution on center surface of contact gap and contact piece are calculated when the current is at peak. it can be found that the intensity of axial magnetic field and radial magnetic field uniformity are strengthened after the iron core is put into, this helps to improve the stability of the vacuum arc
計算了電流峰值時觸頭間隙中心平面和觸頭片上的縱向磁場分佈，可以看出加入鐵芯后縱向磁場強度和徑向磁場均勻性增強，這有利於提高真空電弧的穩定性。The subject of this thesis is to study ironless moving coil linear permanent magnet synchronous motor and the major works in this thesis are summarized as follows : 1 ) two analytical formulas are derived by concentrated current method and distributed current method to determine the magnetic field due to pm, based on the current model of pm. besides, two method ( magnetic charge method and solution by laplace equation method ) are also introduced with comparing their advantages and disadvantages. then the effects of the motor parameters on the flux distribution are discussed
本文對空芯動圈式直線同步電動機進行了深入細致的研究，內容包括： （ 1 ）採用電流模型推導出兩種計算永磁磁極二維氣隙磁場的解析公式（集中電流法、分佈電流法） ，同時介紹了兩種永磁電機氣隙磁場計算方法（磁荷法，直接求解拉氏方程法） ，分析各種方法的優缺點，討論電機參數對氣隙磁密的影響； （ 2 ）介紹了單層同心繞組的布置方式，根據安培定律推導出空芯動圈式直線永磁同步電動機的靜推力計算公式，分析靜態力?位移特性； （ 3 ）建立空芯動圈式直線永磁同步電動機動態模擬模型，模擬不同驅動方式下電動機起動、穩態運行時電磁力、速度、位移的變化情況。Against a prototype which is being produced ， its three dimension end region entity model of stator is established ， and with the aim of simplifying calculation ， the theory of how to simplify entity model is studied ， then the theory is made use of ， and the end region entity model of stator is simplifi - ed ； meshing characteristics of three dimension entity model and shortcomin - gs of end region entity model of stator are studied ， then meshing method of three dimension end region entity model of powerformer stator is studied as well ， and the simplified entity model is meshed with this meshed model ， the distribution of end region magnetic field of stator is analyzed ， and the magnetic field energy and reactance of powerformer end region are calculated and compared with design value because the prototype is being produced ， in this paper ， stator core ， gap and eddy equipment are not taken into consideration ， and this has a little influence on the result ， but through analysis ， the result is proved to be good through the example calculation ， it is known that the method of this paper is useful and through theoretic analysis ， it is proved that end region
針對一臺生產中的樣機，對其建立了定子端部三維實體模型，而且為了達到簡化計算的目的，研究了如何將其簡化的理論，並應用這些理論對樣機定子端部實體模型進行了簡化；研究了三維實體模型的剖分特點和定子端部實體模型存在的缺點，在此基礎之上，研究了對簡化的powerformer定子端部三維實體模型的剖分方法，並且對簡化的實體模型進行了剖分。應用剖分的三維實體模型，用有限元法分析了powerformer定子端部的磁場分佈，計算了端部區域的磁場儲能，並利用磁場儲能計算了powerformer定子端部漏抗，將計算值與設計值進行了比較、分析。由於樣機處在設計生產階段，本文暫時沒有考慮定子鐵心、氣隙和渦流器件對端部磁場的影響，這對分析結果有一定的影響，但是仍然得到較好結果。To sandstone, nmr cuttings analysis can get the same results as core analysis. and the nmr cuttings analysis can also realize the fast measurement of oil saturation, which is difficult for the nmr core analysis in the house at present
採用核磁共振巖屑分析技術不僅可以快速從巖屑中獲得孔隙度、滲透率及可動流體百分數等重要油層物理參數，而且還可以實現巖屑含油飽和度的快速測量，這是目前室內核磁共振巖心分析較難做到的。The calculation to the eddy current on the contact surface and axial magnetic field of contact surface and center surface of contact gap are carried out while the current is at zero. after the iron core of ring type is put in, the eddy current on the contact surface will be increased, the axial magnetic field that the eddy current creates will be also increased
對電流過零時觸頭表面的渦流和觸頭表面及觸頭間隙中心平面上的縱向磁場進行了計算，加入圓環型鐵芯后觸頭表面的渦流增大，渦流產生的縱向磁場增大，在鐵芯中開槽后渦流的平均水平降低，縱向磁場平均值降低。分享友人