磨擦阻尼 的英文怎麼說

中文拼音 [mócāzǔní]
磨擦阻尼 英文
friction damping
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 擦 : 動詞1 （摩擦） rub 2 （用布、 手巾等摩擦使干凈; 揩拭; 抹） wipe; scrub; clean 3 （塗抹; 搽） spre...
  • 阻 : 動詞（阻擋; 阻礙） block; hinder; impede; obstruct
  • 尼 : 名詞（尼姑） buddhist nun
  • 磨擦 : rub; abrade; abrase磨擦電 triboelectricity; 磨擦工 rubber; 磨擦劑 abrasive; 磨擦器 grater; rubber...
  1. Taking the contact stress, bend stress stiffness and temperature stress as the condition, taking the weight of the kiln tyre as optimization aim function, the redia and the width of the tyre are optimized general optimize methods just consider the affecting of the parameters to aim function, but in fact, structural parameters ( such as structure dimension, interval and so on ), physics and dynamics ( damp factor, conduct factor, friction factor material ' s elastic module strength limits and so on ), which would be changed after used. the difference are called discrepancy robust design ' s basic concept is : all design parameters " discrepancy will affect the aim funct ion and arouse the quality target discrepancy

    一般的優化方法，僅僅考慮了參數對其目標函數的影響，而實際情況下有些參數是變化的，產品的結構參數（如幾何尺寸、間隙等） 、物理和力學參數如阻尼系數、傳導系數、磨擦系數、材料的彈性模量和強度極限等的設計值與製造后和使用中的實際值會有差異，這種差異稱為設計變量和噪聲因素的變差。
  2. Damp - the friction for goal. higher values dampen the effect of the goal on the soft body

    阻尼-作為目標的磨擦力。較高的阻尼數值使目標對軟體的效果。
  3. G damp - the friction for goal. higher values dampen the effect of the goal on the soft body

    阻尼-作為目標的磨擦力。較高的阻尼數值使目標對軟體的效果。
  4. Plastic deformation happened in the worn surface where fe element was found, so pam micro - fiber supported part of the load and prevented the further deformation. on the condition of high speed and high load, the worn surface of pam1 / nylon 6 composites was nearly melted and formed comparative uniform transfer on the surface of steel, which accounted for the rather low wear mass loss. the infrared analysis showed that the a small quantity of transition of crystal form from into of nylon and its composites happened during the friction because of the high temperature and strong sheering strength

    通過對復合材料耐磨性能研究表明：復合材料的摩擦系數隨載荷的增加而逐步下降，且磨損表面有明顯的塑性變形；從能譜分析結果來看，復合材料表面有fe的存在，表明pam微纖承受了部分載荷，並阻止了基體的進一步塑性變形及粘著轉移；在高速高載時， pam1 /尼龍6磨損表面處于粘流態，並在鋼環表面形成了連續的轉移膜，表現出較好的耐磨損性能，且在高溫和強剪切力的作用下，材料基體發生了少量的晶體向晶體的轉移。
分享友人
分享到 Line

分享到臉書