磨料粒度 的英文怎麼說
中文拼音 [móliàolìdù]
磨料粒度
英文
abrasive grain-
Abrasive macrograins - determination of capillarity iso 9137 : 1990
磨料粒度.毛細作用測定Abrasive grains - sampling and splitting iso 9138 : 1993
磨料粒度.取樣和分割Abrasive grains - test - sieving machines iso 9284 : 1992
磨料粒度.篩分試驗機Testing method for bonded abrasive grain size
粘接磨料粒度的試驗方法Abrasive products - checking the grit size of superabrasives
磨料製品.超級磨料的磨料粒度的檢驗Cast shot and grit size specifications for peening and cleaning
噴丸和清理用鑄造鐵丸和磨料粒度規范Abrasive grains. sampling and splitting
磨料粒度.取樣和分離Abrasive grains and crude - chemical analysis of silicon carbide iso 9286 : 1997
磨料粒度.碳化硅的化學分析Comparison chart for grit sizes
磨料粒度尺寸參照表Abrasive grains - determination of bulk density - part 1 : macrogrits
磨料粒度.堆積密度的測定.第1部分:粗磨粒Coated abrasives - grain size analysis - part 1 : grain size distribution test
塗附磨具用磨料粒度分析第1部分:粒度組成Bonded abrasives - determination and designation of grain size distribution - part 1 : macrogrits f4 to f220
固結磨具用磨料粒度組成的檢測和標記第1部分:粗磨粒f4 f220Bonded abrasives - determination and designation of grain size distribution - part 2 : microgrits f230 to f1200
固結磨具用磨料粒度組成的檢測和標記第2部分:微粉f230 f1200Coated abrasives - grain size analysis - part 2 : determination of grain size distribution of macrogrits p12 to p220
塗附磨具用磨料粒度分析第2部分:粗磨粒p12 p220粒度組成的測定Coated abrasives - grain size analysis - part 3 : determination of grain size distribution of microgrits p240 to p2500
塗附磨具用磨料粒度分析第3部分:微粉p240 p2500粒度組成的測定Bond abrasives - determination and designation of grain size distribution - macrogrits f230 to f1200
粘合磨料.粒度分佈的測定和標記.第2部分:粒度范圍為f230 - f1200Coated abrasives - grain size analysis - determination of grain size distribution of microgrits p240 to p2500
砂紙.粒度分析. p240 - p2500粗磨料粒度分佈測定Coated abrasives - grain size analysis - determination of grain size distribution of macrogrits p12 to p220
砂布.粒度分析.第2部分: p12 - p220粗磨料粒度分佈測定Dental rotary instruments - diamond instruments - part 3 : grit sizes, designation and colour code
牙科旋轉儀器.金剛石儀器.第3部分:磨料粒度牌號和色碼The influences of the given speed, the size of the grain and the static load on the numerical controlled ultrasonic machining efficiency were discussed, the grey system theory was used to carry on the related analysis to these three factors, the main influence factors and secondary influence factors were found out, this can be used as the criteria in setting up the parameters in ultrasonic machining
探討二維數控超聲加工中工具移動速度、磨料粒度、靜壓力對超聲加工效率的影響,運用灰色系統理論對這三個因素進行了灰關聯分析,找出影響加工效率的主要影響因素和次要影響因素,為超聲加工中參數的設置提供了依據。分享友人