空抽井 的英文怎麼說

中文拼音 [kōngchōujǐng]
空抽井 英文
pumped-off well
  • : 空Ⅰ形容詞(不包含什麼; 裏面沒有東西或沒有內容; 不切實際的) empty; hollow; void Ⅱ名詞1 (天空) s...
  • : 動詞1 (把夾在中間的東西拉出; 提取) take out (from in between) 2 (從全部里取出一部分; 騰出) ...
  • : Ⅰ名詞1 (從地面往下鑿成的能取水的深洞) well 2 (形狀像井的東西) sth in the shape of a well 3 (...
  1. Tianjin fengdong heat treatment equipment co., ltd, sino - japanese joint venture, is a specialist firm to produce unicase series multi - purpose complete set, speria series pre - vacuum multi - purpose furnace complete set, uninite gas soft - nitriding furnace complete set, mesh - belt type continuous furnace, pit type bright annealing furnace and pit gas carbonitriding furnace complete set

    全套技術,生產滴注式unicase系列密封箱式多用爐成套設備, speria bbh型預多用爐成套設備,氣體軟氮化爐成套設備,網帶式連續爐,式光亮退火爐及式氣體滲碳爐成套設備,並承接各種非標熱處理設備的設計和製造。
  2. Through analyzing the structure of open caisson, and according to sinking stress principle, the paper introduced in the open caisson construction process sinking, correcting error, survey control as well as peculiar circumstance processing technical measure, such as in open caisson construction the inner - mold for sanding, framework supporting and steel binding, and concrete casting ; in open caisson sinking - control the sand in edge foot inner - mold, sand - pumping sinking, and pressure hydraulic monitor breaking and pressure - blowing sinking by air pressure blower etc

    摘要根據下沉受力原理,分析了沉結構,介紹了沉施工過程中的下沉、糾偏、測量控制以及特殊情況處理的技術措施,如沉製作中的填沙內模,模板支設和鋼筋綁扎,混凝土澆注;沉下沉控制中的刃腳內模沙土,沙泵沙下沉,高壓水槍破壓、壓機吹壓下沉等。
  3. Rational control of the pump ' s work and rest time is the key to solve the problem of void pumping. this essay gives theoretical analysis and cost comparison of every detective method, considers power detection as the most effective method, and puts forward several ways of power consumption and effectiveness power consumption at the same time. the designed electricity saving controller integrate all the above four methods, and it can work with different methods by switch between automatic and manual to broaden its accommodation

    解決油現象的關鍵是合理控制開機時間與停機時間長度,本文對各種檢測方法進行了理論分析及成本比較,認為功率檢測最行之有效,同時提出了功率檢測的幾種實現方法,即瞬時功率法、人工電耗法、設定功耗法及效益功耗法,所設計的節電控制器集以上四種方法於一身,可通過自動手動切換採取不同的功率檢測方法,使其適應范圍增寬。
  4. Application and selection of water - ring vacuum - compressor pump in methane drainage in coal mine

    水環真壓縮機在礦瓦斯放中的應用和選型
  5. As crude oil is extracted continuously in oil field, there are more and more low yield oil wells in old oil field, and the problem of void pumping is becoming more serious. rational control of the pump ' s work and rest time can save electricity, prevent the break of beam hanger caused by beating liquid, and reduce attrition of the pump

    隨著油田原油的不斷開采,老油田的低產越來越多,油現象也越來越嚴重,合理地控制油機的開機時間與停機時間長度,可以達到節電、防止擊液引起的油桿斷裂以及油機磨損減少的目的。
  6. Based on the new technique of vacuum deep wellpoint developed in recent 10 years and the actual conditions in the well water exclusion of foundation pits, a new method for evaluation volume of water was brought forward

    摘要針對近十年發展起來的管內的深點新工藝,根據它在四周有良好隔水的基坑中降水的實際情況,提出了一種水量估算和點設計的新方法。
  7. The results show that the increase of vacuum energy can not expand the influence scope of vacuum degree obviously when vacuum degree under membrane is high. the vacuum degree in the pvds is higher than vacuum degree in the sand drains, and the vacuum degree in the sand drain is higher than vacuum degree in the silt at the same depth in the ground during the initial stage of pumping

    分析結果表明:當膜下真度較高時,真能量的增加不會明顯增大真度的影響范圍;在的初期,一般在地基相同的深度處:塑排真度砂度淤泥真度。
  8. To prevent pumping system stopping working, working without efficiency and being destroyed, so it is very important to monitor oil - well. the thesis dissertates the process of developing displacement - load sensor which collects displacement data and load data to form the indicator diagrams, researches the means based on rbf neural network of recognizing fault types, designs parts of hardware and software of the mainframe of the oil - well monitor and control system, and debugs the entire oil - well monitor and control system

    為了防止油機故障停機、無油、不法分子的蓄意破壞等情況的發生,因此對油工況進行實時監控顯得尤為重要。本文論述了採集用於形成油示功圖的位移和載荷數據的傳感器的研製,包括硬體電路和軟體的設計,對基於rbf神經網路的油工況模式識別方法進行了研究,對監控系統主機的部分硬體電路及相應的軟體進行了設計,並對整個油監控系統進行了聯調和測試。
分享友人