空氣調節孔 的英文怎麼說

中文拼音 [kōngqìdiàojiékǒng]
空氣調節孔 英文
air louver
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 氣 : Ⅰ名詞1 （氣體） gas 2 （空氣） air 3 （氣息） breath 4 （自然界冷熱陰晴等現象） weather 5 （氣味...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 空氣 : 1 （大氣） air; atmosphere 2 （氣氛） atmosphere 3 （氣閘） air brake4 pneum ; pneumo ; pneumat ;...
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  1. Long - hole and geometrical proportion type of mixing unit is finally adapted in lpg supply system, and power and torque output of lpg engine are improved by increasing compression ratio, and ignition characteristic is tried to adjusted to satisfy engine performance. meantime emission performance and noise level of lpg engine at full - throttle and other various part - throttle operations are tested and compared with former gasoline engine. ( 3 ) it is verified by engine dyno tests that lpg engine has better synthesized performance at aspects of power and torque, fuel economy, as well as emission than former gasoline engine

    選擇了等比例長孔式混合器控制空燃比；通過提高壓縮比來彌補動力性的損失；以動力性為主控目標，對最大功率點、最大扭矩點、中等轉速、最低轉速點所對應的發動機轉速做了點火特性的調節；通過空燃比的合理控制，直接改善發動機的動力性、經濟和排放指標；作為對缸內燃燒過程的理論分析，進行了燃燒特性的實驗測試；對原汽油機和新開發的液化石油氣發動機，進行了外特性和部分負荷特性以及怠速的排放及噪聲對比性測試。
  2. Therefore, the purpose of this thesis is to look for a suitable preparing process for 3 - tcp with their micro - construction controlled more easily and the porosity rate and strength uniform. this paper created a new preparing method of porous ceramics, i. e. foam gel - casting technique, which integrated foam technique in porous ceramics preparing and gel - casting technique in structural ceramics preparing was applied to improve the preparing technique of porous p - tcp bioceramics in order to prepare ceramics bodies with high body intensity, controllable porosity and easily machining performance

    因此，本論文努力尋求一種適合於- tcp多孔陶瓷的制備工藝，使其微觀結構易於調節控制，空隙率和強度達到平衡同一。在實驗中，結合了制備多孔陶瓷常用的發泡法和結構陶瓷制備中的注凝法，創新設計了一種新的多孔陶瓷成型方法? ?泡沫注凝法，對多孔- tcp生物陶瓷的成型工藝加以改進，制備出高強度、氣孔率可控以及易加工的陶瓷坯體。
  3. In this paper, we aim at establish heat and mass coupled transfer model in the building wall, the emphasis of this study lies in creating a coupled and non - linear diferential equation system for the heat air and moisture transfer in the wall, which can be described by means of continuum mechanics and irreversible thermodynamics, the most dominant factor is moisture conten 9la gas pressure pc and temperature t, for the description of heatair and moisture transport, the general mass balance equation can be expressed by the temporal change of moisture conten 9 l, gas pressure pc and temperature t that means, in order to create a closed solvable equation system, the other additional dependencies have to be found, which the other variable depending on the variables of the solution : moisture conten 6 l gas pressure pc and temperature to the model is verified by the numerical simulation software which has been developed about building wall.,

    根據節能設計要求，本文用熱力學的方法，並根據多孔介質中多相流體流動描述方面的最新研究成果? ?體積平均方程，建立了墻體熱、濕和空氣耦合熱質傳遞模型，並推導出熱、濕和空氣耦合傳遞等效擴散方程；找到建築墻體熱、濕及空氣耦合作用下熱質傳遞過程的主要影響因素濕容量_ l 、氣壓p _ c和溫度t 。開發了單體材料墻體熱質傳遞數值模擬軟體，用實測數據對軟體進行調試並對模擬計算結果進行了驗證。模擬出了單材料墻體在熱、濕和空氣耦合作用下建築墻體內的溫度和濕度分佈規律。
  4. The results show that transformation of transmission mechanism and much higher birefringence can be achieved after nlc - filling. farther, we firstly demonstrate the realization of modulating pbg and modes of pbg - pcfs by changing refractive index filled of filled nlc by virtue of temperature or electric field, and finally tunable

    在此研究的基礎上，首次提出並設計出通過用溫度或者電磁場來調節空氣孔中液晶的折射率來連續調節這種高雙折射光子帶隙光纖中的傳輸帶隙和傳導模式，最終實現的高雙折射可調的光子帶隙光纖。
分享友人
分享到 Line

分享到臉書