空隙填料 的英文怎麼說

中文拼音 [kōngxìtiánliào]
空隙填料 英文
infilling
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 隙 : 名詞1 （縫隙; 裂縫） crack; chink; crevice 2 （空閑） gap; interval 3 （漏洞; 機會） loophole; op...
  • 填 : 動詞1. （墊平或塞滿） fill; stuff 2. （補足; 充滿） replenish; supplement; complement 3. （填寫） fill in; write
  • 料 : 名詞1 （材料; 原料） material; stuff 2 （喂牲口用的穀物） feed; fodder 3 （料器） glassware 4 （...
  • 空隙 : 1 （時間上的） interval 2 （空間上的） gap; space; clearance; separation; air gap （ag）; slot; [...
  1. Stereoscan photographs showed that both the inner and outer coating membranes of sapcus were formed by different size and shape micro particles of coating materials, which were closely stacked at random

    高吸水性樹脂包膜尿素的內外膜均是由大小不一形狀不規則的包膜材料微粒無序緊密堆積，並由膠粘劑填充空隙膠聯而成，包膜疊層間和疊層內有微小孔隙，它們是尿素溶出的通道。
  2. When use the fireproof bag to seal and plug the hole of cable, first treat and arrange the cable in the hole, then edge the fireproof bag into the gap between cables, cable and plugging material or floor plate, put it interlaced just as laying bricks or stones and fill it firm and tightness as possible

    在使用阻火包封堵電纜孔洞時，先將孔洞電纜作必要的整理和排列，然後將阻火包平服地嵌入電纜與電纜，電纜與堵料或樓板間的空隙中，像砌磚那樣交錯放置的方法，盡量填充密實。
  3. This thesis for the first time bases its analysis on the maintenance characteristics and repair mechanisms for crack filling and pothole repair in asphalt roads. it analyzes the properties of the aggregate and the bituminous binder in patching materials, and further analyzes the compatibilities of the aggregate and the bituminous binder, patching materials and old pavement materials. furthermore, it determines the grading types, the mineral aggregate gradations, the application rate of asphalt, the principle of selecting component materials and the air void

    本文首次依據瀝青路面裂縫填封和坑槽修補的維修特性和修補機理，全面分析了修補材料中集料與瀝青結合料應具備的性能要求，並對集料與瀝青結合料、修補材料與原有路面材料的相容性進行了深入的分析，同時分析確定了修補材料的級配類型、礦料級配、瀝青用量范圍、組成材料的選用原則及空隙率等。
  4. When sticky molding takes place during manufacturing, the prime concern is whether the injection pressure and the consistant pressure is too high. high injection pressure will result in over saturation, causing the difficulties in mold release when the plastics materials fill in other gaps

    在加工過程中發生粘模，首要考慮射壓或保壓是否過高，射壓過高會使成品過度飽和致塑料填充入其它空隙中產生脫模困難。
  5. Owing to its thin wallow resistance, high void and capacity, metallic packings have a high separation efficiency, and applied to handle the thermal sensitive, hard to sepoaration and easy carbonized materials in the vacuum rectify9ing tower

    金屬填料材質主要包括碳、鋼、鋁合金及不銹鋼等.由於其壁、空隙率大、通量大、阻力小、分離效果好.特別適用於真空精餾塔，處理熱敏性，易分解、易結碳的物料
  6. Ultrasonic plastic welding theory is generated by the generator 20khz or 15khz pressure, high - frequency signals, the system can be adopted for the high - frequency signals into mechanical vibrations, and in plastic products working, through working surface and internal friction among elements spread by the department of the interface temperature, when the temperature reached the melting point of her own, that the working interface rapid melting, and then fill in the gaps between the interfaces when shock stop working at a certain pressure and cooling will be a perfect welding

    的高壓高頻信號通過換能系統，把信號轉換為高頻機械振動，加於塑料製品工件上，通過工件表面及內在分子間的磨擦而使傳處到介面的溫度升高，當溫度達到此工件本身的熔點時，使工作介面迅速溶化，繼而填充于介面間的空隙，當震動停止，工件同時在一定的壓力下冷卻定形成完美的焊接.點擊數： 723錄入時間： 2006 - 5 - 14
  7. Study on workability - design of fresh concrete was carried out by introducing coefficient of filling - voids of mortar ( cfvm ), where cfvm was the ratio of voids content of densely packed coarse aggregates to the volume of mortar in concrete

    在新拌混凝土工作性設計中引入了砂漿填充系數c _ （ fvm ）的概念， c _ （ fvm ）是混凝土中砂漿體積與粗集料振動密實空隙體積的比值。
  8. They are widely applied in the tower of coking desulfurizing, benzene scrubbing, naphthalene scrubbing, ammonia scrubbing and chemical fertilizer hot water saturation tower, electric power plant wet cooling tower

    該系列填料具有比表面積大、空隙率高、傳質系數大、抗堵塞、抗腐蝕、耐急冷急熱、使用壽命長、易安裝的優點，是一種理想的塔填料。
  9. They usually have an empty center in them for fillings and sauces

    通常，它們都有用來填充餡和調味料的空隙。
  10. Tests for mechanical and physical properties of aggregates - part 4 : determination of the voids of dry compacted filler ; german version en 1097 - 4 : 1999

    集料的機械和物理性能試驗.第4部分:密實填料空隙測定
分享友人
分享到 Line

分享到臉書