端距長度 的英文怎麼說

中文拼音 [duānjùzhǎngdù]
端距長度 英文
endtoend lengthth
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 距 : Ⅰ名詞1 （距離） distance 2 （雄雞、雉等的腿的後面突出像腳趾的部分） spur （of a cock etc ）Ⅱ動詞...
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 端距 : apical calcaria
  • 長度 : length; longitude; size; extent; footage
  1. The regularities of pile - top reaction distribution, the carrying load ratio between pile and raft, the settlement and the imparity settlement of foundation in the frame - tube structure and the single wall are influenced by some factors such as the stiffness of the superstructure, the intensity of the soil under the piles, the length and radius of the piles, the distance between the piles, the thickness and the suspended width of the raft

    對豎向荷載作用下的空間筒中筒結構、樁筏基礎和地基進行了三維有限元分析。研究整體結構和單片墻結構在上部結構剛度、樁端土強度、樁長、樁徑、樁距、筏板厚度、筏板外挑寬度等影響因素變化時的樁頂反力分佈規律、樁筏荷載分擔比、樁基沉降和差異沉降規律。
  2. Muzzle : of medium length ; that is, the distance from the tip of the nose to the stop is equal to the distance from the stop to the occiput

    鼻口部：中等長度；意思是，從鼻子的頂端到額段（凹陷處）的距離等於從額段到后頭部（枕骨部）的距離。
  3. The main results show that : ( 1 ) the mechanism of laser bending is very different from that in bending with hard tools. ( 2 ) the bending angle is varied along scanning direction, and there is a deformation wave in the process. ( 3 ) the effects of sheet length on bending can be neglected while the length is more than 10 times of thickness. ( 4 ) the sheet width has much higher influence on the bending process

    分析發現：激光彎曲成形時板料的應力狀態與機械折彎時有根本不同；當激光束沿直線單向掃描時，板料兩端的彎曲角度不同；板料的長度大於10倍板厚或5倍光斑尺寸時，板長對彎曲角度的影響不再顯著；沿掃描方向，距離光斑中心3倍光斑尺寸以外的區域，仍然對彎曲變形量產生影響。
  4. Based on the comprehensive analysis of the application status and the existed problems of transmission line fault location, this dissertation presented a new algorithm for fault location based on two - terminal asynchronous data, which can make correction for the integrate error of line parameter, length of transmission line, sampling value and so on. at the same time, it can work out the two - terminal asynchronous phase angle with the corrected parameters

    本論文在充分分析了國內外故障測距的理論與技術以及存在的問題后，針對輸電線路故障定位因線路參數變化對定位準確度的影響，提出了能夠對線路的參數、長度和采樣值等誤差等進行綜合誤差修正（ cie ）的新演算法，並利用修正後的參數來求解兩端的不同步相角差。
  5. For the laminate which contains a crack, the suggested patch shape is rectangle, the patch thickness is equal to the parent laminate and the patch stacking sequence is the same as the parent laminate. because the length and the width of the patch have the fewer influence on the repair effect, the patch has the least weight on the basis of enough edge distance, end distance and space having been promised

    ?對于含裂紋復合材料層壓板，長方形補片的長度和寬度對修補效果沒有非常明顯的影響，因此在保證連接邊距、間距和端距的條件下，補片大小的選擇應該以節省重量為原則；而當補片的鋪排順序與母板相同、相對厚度為100時能夠獲得比較好的修補效果。
  6. As far as input coupling devices concerned, we design a feasible taper coupler by means of the theory of waveguide coupling and outside cavity waveguide laser and make decision of the sizes of the lens and the taper coupler, and the relative distance of them. the focus of the lens is 65mm and the radius is 5mm. the length of the taper coupler is 15mm, and the radiuses of the input and output ends separately are 17mm and 0. 65mm

    在輸入耦合器方面，藉助于波導耦合和外腔式波導激光器的相關理論，設計了工藝上可行的錐型耦合器，確定了透鏡、耦合器的尺寸以及耦合器與透鏡的相對位置：耦合透鏡的焦距為65mm ，直徑為srnm ，耦合器的長度為15mm ，輸入端直徑為17mm ，輸出端直徑為0
  7. This may be done by ensuring that both leads are of equal length to equalize thermal conduction through them, by making any airflow ( whether forced or natural convection ) normal to the resistor body, and by taking care that both ends of the resistor are the same distance from any heat source on the pcb

    例如，讓電阻兩端的引腳長度相等以使熱阻相等；讓冷卻氣流（自然風冷或強制風冷）均勻地吹到電阻上；或者讓電阻兩端與pcb上的熱源的距離相等。
分享友人
分享到 Line

分享到臉書