等值梁 的英文怎麼說
中文拼音 [děngzhíliáng]
等值梁
英文
equivalent girder-
It is the key of ebfs, therefore, furthermore calculation about link are carried out in this thesis, introduced achieved research, summarized the affect of link on whole capability in the first, the second, numerical calculation are proceeded on link with ansys : with the purpose of discussing yielding mode critical length of link, established five different specimens ; with the purpose of discussing the influence of h / tw of web, b / tf of flange and h / b, established eighteen different specimens ; with the purpose of discussing the affect of stiffener, established four different specimens, and elaborated the affect of stiffener on link based on achieved test researches
因此，本文對耗能梁段進行進一步計算分析，概述耗能梁段對整體性能的影響，並利用有限元程序ansys對耗能梁段進行數值計算：針對耗能梁段的屈服類型建立5種不同長度的模型，計算討論耗能梁段屈服類型的長度劃分；針對耗能梁段腹板高厚比、翼緣寬厚比以及梁段截面形狀等因素共建立了18種模型進行計算分析；針對加勁肋對耗能梁段的作用建立了4種模型，並結合已有的試驗闡述了加勁肋對耗能梁段的影響。On the base of codes in 1989, a series of seismic measures are improved in new codes, such as limit of inner - storey drift angle, minimum reinforced rate, column - beam moment magnification coefficient and moment magnification factor at the column base, etc
在89規范的基礎上，本次規范修訂進一步提高了包括層間位移角限值、最小配筋率、柱一梁級差系數等等在內的一系列抗震設計措施。Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed
在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。A new prestressed bowshaped structure strain multiplier was designed to solve problem which strain amplitude is much lower than the threshold of fatigue life gage, and this strain multiplier take the advantages of entire structure, lower stiffness, good reliability and convenience to use
設計出一種弓形預應力結構應變倍增器，解決了橋梁應變幅值遠遠低於疲勞壽命計門檻值這一關鍵問題，此倍增器具有整體性強、剛度低、可靠性好、使用方便等優點。Also, the thesis calculate and analysis the transverse deflection of steel box girder deeply in multiple factors. firstly, the article introduced the calculative methods and theory of local stress and strain of bridge structure. then program software system of finite element method was introduced. after that, the influential factors to the calculatial result and their values were analysed and suggested
本文首先介紹了橋梁結構局部應力應變計算理論和方法，對有限元計算程序進行了介紹，然後分析了縱橫隔板設置、梁高及梁寬變化等因素對鋼箱梁橋面板在恆載作用下的橫向撓度的影響，並將這些計算結果進行對照分析，從而找出了影響橋面板橫向撓度的主要影響因素，並得出了相應的數值可供工程實踐參考。From the feature of the force and deformation of the tpih, 5 different elements are used to mesh the different zones of the tube, which are structural beam 3d elastic 4, structural pipe plastic straight 20, structural pipe elastic elbow 18, structural shell elastic 4 node 63 and contact 3d pt - to - surf 49 ; the contact problem is assumed to be flexible - to - flexible ; the temperature field is assumed to be body load. a mechanical model corresponding to reality has been established for numerical simulation. based on the above, the 3 - d fem numerical simulation of tpih has been carried out by using the ansys program
針對加熱彎管過程的受力和變形特點，採用三維梁單元、三維塑性直管單元、三維彈性曲管單元、三維殼單元與三維點對面接觸單元等5種不同的單元分別對管毛坯不同區域進行劃分，並對接觸單元採用柔體-柔體的處理方法，將溫度場作為體載荷處理，建立了符合實際的加熱彎管問題數值模擬力學模型：在此基礎上，應用商用軟體ansys對加熱彎管過程進行三維有限元模擬與研究，獲得了成形時推力、彎矩、支撐力大小及其變化趨勢。The research fruits in this article can provide the temperature isoline map of crown cantilever section and central longitudinal section of the dam, the stress isoline map of crown cantilever section and upstream and downstream surfaces of the dam, the maximal and minimal stress distribution map in dam abutment along with the height of dam, the maximal and minimal stress table of typical nodes and the maximal and minimal stress table in different elevations, and also provide reference basis for taking relative temperature control measures in the design and construction of rcc arch dam
本文研究成果可給出壩體的拱冠梁剖面和壩體中心縱剖面的溫度等值線圖、拱冠梁剖面和壩體上下游面應力等值線圖、壩肩最大最小應力沿壩高的分佈曲線、不同高程處典型點的最大最小應力值表以及不同高程處最大最小應力值表等成果，為碾壓混凝土拱壩的設計和施工中採取相應的溫控措施提供了參考依據。According to eigenvalue equation ( general formula ) of the energy method of the plane steel frame structure stability, and considering the restriction of the end of the column of the main steel frame and function of deflection curve gained from the differential balance equation general resolution, we get the equation for calculating the length coefficient of the main frame structure stability of the steel arch gate and the resolutions are also given
根據平面剛架穩定性能量法特徵值方程（通式） ，考慮弧形鋼閘門主框架柱的柱端約束的特殊情況，求出撓曲線函數（試解函數）通解，得到弧形鋼閘門主框架柱穩定性計算長度系數方程。其中弧門主框架主橫梁式形框架的臨界荷載比較現行規范推薦的有限元法簡單方便、結果精確及物理概念明確等優點。Considering the stiffened plate as a composite system of grillage beams and slab, the superstructure as an equivalent rigidity plate, a semi - analytical and semi - numerical method, which makes use of compatible analysis of force and displacement among beams and slabs and columns and ground, is developed to analyze interaction between stiffened raft foundation and subsoil considering the rigidity of superstructure
摘要將彈性地基上的梁板式矩形筏基視為十字交叉梁與平板組合體系，上部結構剛度簡化為等效剛度板，採用半數值、半解析方法，通過梁、板、柱以及地基之間力與位移平衡協調分析，可得到考慮上部結構剛度時梁板式筏基寫地基共同作用的半數值、平解析解。Combined with practical data of shannxi lin hekou hydropower plant, the temperature filed of m and n schemes during construction and operation are simulated and analyzed. the isoline map of stable temperature field of the arch crest girder section and the vertical section in the center of arch dam, the isoline map of unstable temperature field of the arch crest girder section and the vertical section in the center of arch darn during construction and operation and the maximal and minimal temperature value during construction and operation are provided. the distribution law of temperature in the dam and the form reason of high - temperature zone are analyzed and the effect and feasibility of cooling and the zone of cooling are discussed
結合陜西藺河口水電站工程實際資料，對m方案和n方案溫度場進行了施工期和運行期全過程模擬計算分析，給出了拱冠梁剖面和壩體中心縱剖面準穩定溫度場等值線圖以及施工期、運行期拱冠梁剖面和壩體中心縱剖面非穩定溫度場等值線圖，提供了施工期逐月和運行期每年最高、最低溫度等成果，分析了壩體溫度分佈規律以及高溫區形成的原因，並探討了預埋冷卻水管的效果和可行性以及預埋冷卻水管的區域。3 ) the influences on the internal forces by some variable parameters such as the ratio of the rise to span and the stiffness ratio are compared. the optimal range of these parameters is pointed out and some advances are also given
研究探討了矢跨比、拱梁剛度比等參數對預應力混凝土連續梁拱組合體系橋梁結構內力的影響，並得出合理的取值范圍，為設計人員選取結構參數提供參考。As is well known, the effective width depends on several factors, such as the cross - section width, the height of web, the spacing of span and so on. we can conclude that width / span ratio ( overhang width / span and central width / span ) is the governing factor of the effective width
影響箱形截面樑上翼緣有效寬度的因素很多，如上翼緣寬度、梁高、跨度以及結構體系等，通過大量計算表明寬跨比[翼緣部分寬度、箱室部分寬度與跨度的比值]是有效寬度的控制影響因素。The difference between axial compressive capacity of beam - column joints and that of columns is introduced when joints are strengthened by various measures. influence of shapes, spiral hoops and ratio of beam depth to side dimension of square column upon axial compressive capacity of beam - column joints is discussed. then economy and security of the relative article in current code are demonstrated and the design recommendations of beam - column joints are given
本文通過6個不同強度等級混凝土樑柱節點試驗，了解在不同的加強措施情況下，節點區的軸心抗壓承載力與柱的理論軸心抗壓承載力的差異，探討了角鋼、螺旋箍筋及梁高與柱截面尺寸的比值h c對節點區軸心抗壓承載性能的影響，驗證了我國現行規范有關條款的安全性和經濟性，並且在此基礎上，為不同強度等級混凝土樑柱節點的設計提出了相關建議。Hydraulic pile hammer is one of the pile driving machines that drive prefabricated piles into the ground in the construction of pile foundation such as construction, bridge, dock, etc. with the development of science and technology, the prefabricated pile driving machines evolve from block hammer, steam - hammer, diesel hammer to hydraulic hammer. hydraulic pile hammer is one of ideal prefabricated pile driving machines because it can adjust stress waveform, decrease stress peak value, prolong effectual action when it drives piles. hydraulic pile hammer is used widely and formed series in developed countries now
液壓打樁錘是用於建築、橋梁、碼頭等樁基礎施工中打入預制樁的樁工機械。隨著科學技術的進步，預制樁施工機械由落錘、汽錘、柴油錘，發展到了液壓打樁錘。用液壓打樁錘打樁，可以調整撞擊應力波波形，減小應力峰值，延長有效作用時間，是一種比較理想的預制樁施工機械，目前在發達國家已被廣泛使用，並形成了系列化。Firstly, for the system of moulding board and support frame in construction the side pressure and screws are analyzed. the material and structure form of support frame are discussed. the design of support frame uses the method of limited state, and also it analyses the integer stability, part stability, and single stability, and then proposes the load analysis of multi - level support frame
首先，針對轉換層梁模體系及支撐架施工，重點分析了轉換層結構現澆混凝土對模板側壓力值及模板對拉螺桿的計算；討論了轉換層支撐體系的形式及構造，詳細論述了基於極限狀態設計的支撐架計算方法，包括縱橫向水平桿的強度驗算、立桿的整體穩定性、局部穩定性、單肢桿件穩定性等驗算，並提出了多層支撐架的施工荷載計算方法。The company is capable to design and manufacture all alone all kinds of containers and flow office con | ainers, and as request make structurally special enntainers and flow office containers, such products with large capacity and extra height and lcngth as steel containers, ventilators, open top containers, open side containers, eqnipment containers for special purpose, office maintenance containers, living containers, rush bin, toilet case, watch house - ease, containers for dining hall, 2 in 1 or 3 in l office compound meeting room, collapsible containers, and other containers and flow office containcrs of distinct sizes
佛山市南海平洲友利集裝箱有限公司能自行設計製造各類集裝箱及流動辦公室箱，也能按客戶要求製造特殊構造的集裝箱及辦公箱，如大容積超高超長的鋼質集裝箱、通風箱、開頂箱，側開門箱、設備專用箱、辦公裝修箱、住宿箱、垃圾箱、廁所箱、值班室箱、飯堂用箱、二合一或三合一組合辦公會議室箱、裝拆箱及其他不同尺寸的貨箱及辦公箱和集裝箱專用部件、八字板、頂板、側板、低橫梁、角柱頭等。After comparing between the finite - element analysis and experimental results, the author verified the fem. then according to the chinese code, the nonlinear finite model of the beam - to - column is established which are made of different size components. the responses of beam - to - column web moment connections which are made of different size components are compared and analyzed from three facets, and the conclusions about the joints behavior are drawn : thicken the connection plate, lengthen the connection plate or use a back - up stiffer can improve the connection behavior, consist of improving the behavior of load - supported and reducing the stress convergence in the flange moment plates
本文根據我國規范的有關規定，自行建立了12個不同構件尺寸的樑柱腹板連接的三維有限元模型，對不同構件尺寸的樑柱腹板剛性連接節點在單向荷載作用下的反應進行了研究，從結構的mises應力等值線示意圖、梁端加載處的荷載? ?位移曲線、翼緣連接板兩端的mises等效應力以及翼緣連接板與柱相連接的三邊的mises應力等值線示意圖四方面進行了比較與分析，從而得出了不同構件尺寸的樑柱腹板剛性連接的在受力行為上的結論：增加翼緣連接板的厚度、增加翼緣連接板的長度以及採用柱的橫向加勁肋均可以改善節點的受力性能：提高節點的承載能力；減小翼緣連接板內部與柱翼緣邊的的應力不均勻現象，從而避免試件過早地發生破壞。At the same time, they must perform their duty to criticize their government and lead their people as well. for access this goal, liang chi - chao emphasized that journalists must burden their own duty and contribute all of theirs for their motherland and people ' s benefits. based on this, journalists should rule their work due to a series of moral rules, such as dedicate them in their business, pursue them for society value, and so on
為了實現報刊的價值，梁啟超強調報人必須加強道德修養，確立「天降任，吾不辱」的職業良心、 「茍利國家生死以」的職業態度，並以此為指引，形成有利於報刊價值實現的一系列道德規范，如敬業、公正、真實、講求新聞價值和社會價值、把握時效性、甘於犧牲，等等。Abstract : in this paper, a new simple method is put forward to on - line survey and analyse the real - time response of bridges loaded under random vehicles and people. based on linear elastic hypothesis and finite element method, the dynamic whole displacement state and load of the bridge can be obtained through surveying partial displacements, so the problem that load is unknown and difficult to determine when calculating is solved in a sense. this method is adap ted to girder bridge, arch bridge, cable - stayed bridge and suspension bridge. through the instrumentality of ways and means in this treatise, a real - time system to survey and analyse a working bridge can be established
文摘:在線彈性假設基礎上，根據有限元理論和橋梁隨機車輛（行人）荷載的特點，討論並提出了一種通過監測部分位移，計算橋梁其餘位移和橋面荷載的簡化分析方法，解決了橋梁在隨機車輛（行人）荷載作用下的荷載確定問題，建立了動位移和等效節點荷載的有限元列式.該方法為橋梁結構的在線監測和實時分析提供了理論基礎，適用於連續梁橋、拱橋、斜拉橋和懸索橋等橋梁結構形式，具有實際應用價值Equivalent beam method
等值梁法分享友人