等弧長分段 的英文怎麼說

中文拼音 [děnghúzhǎngfēnduàn]
等弧長分段 英文
equal arc length segments
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 弧 : 名詞1. [數學] （圓周的任意一段） arc2. （古代指弓） bow
  • 長 : 長Ⅰ形容詞1 （年紀較大） older; elder; senior 2 （排行最大） eldest; oldest Ⅱ名詞（領導人） chief;...
  • 分 : 分Ⅰ名詞1. （成分） component 2. （職責和權利的限度） what is within one's duty or rights Ⅱ同 「份」Ⅲ動詞[書面語] （料想） judge
  • 段 : Ⅰ量詞（部分） section; segment; part; paragraph; passage Ⅱ名詞（姓氏） a surname
  1. Fluid noise mainly comes from out put pulsation of rate of flow, the main reason of out put pulsation of rate of flow is the instant high pressure return flow that obturation cubage produced when the big round curve pressure transition. the v trough on the port plate can reduce the fluid noise. in this paper, the author based on the acting of dam a river and condensability of liquid and used matlab language as tool to calculate the v trough on the original port plate and drew out the p - t diagrammatic curve and analyzed its shortcoming and improved the design of original v trough and got that the best size of its angle was 12. 3 and its length was 5mm and the cross section was an equilateral triangle

    流體噪聲主要來源於輸出流量脈動，造成輸出流量脈動的主要原因是閉死容積在大圓弧段壓力切換時產生的瞬時高壓迴流，在配流盤上開設v型尖槽可降低因高壓迴流而引起的流體噪聲，本文以截流作用和液體的可壓縮性為理論依據，以matlab語言為工具，對原配流盤上的v型尖槽進行了理論計算，繪制出p - t圖線，分析了它的不足，並對原有v型尖槽進行了優化設計，得出了v型尖槽的最佳幾何尺寸：配流盤平面上的v型尖槽的兩邊的夾角為12 . 3 ，槽長5mm ，槽的橫截面為等邊三角形。
  2. Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  3. Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder

    文摘:從單焊道全位置區段、送絲行為、焊接弧長（電壓） 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點，其研究成果對全位置焊接機的製造和調試具有普遍指導意義。
  4. Test results indicated : with the hoist of altitude, the increase of ice amount and the rise of pollutant, the average flashover voltage reduced. the character exponent generally depends on the insulator profile, ice amount, ice state and pollution severity etc. by means of a high - speed camera, a data acquisition system and high voltage test facilities, a series of the flashover processes on ice surfaces were record. the experimental results form this study and the subsequent theoretical analyses suggested : the thermal ionization of the air in front of an arc root resulted in arc movement ; the electrostatic force had an auxiliary effect of impelling arc propagation ; the electrical

    通過對攝像機、數據採集系統及高壓試驗裝置記錄覆冰絕緣子表面閃絡電弧的發展過程的試驗結果進行理論分析得出：弧根周圍空氣的熱電離導致了電弧的發展，靜電場力對電弧的發展起到了加速作用，電擊穿僅發生在閃絡最終的跳躍階段；通過測量閃絡過程中的放電電壓、泄漏電流、閃絡時間、覆冰水電導率、電弧長度及電弧半徑等參數，得到了不同階段電弧（電弧起弧階段、電弧發展階段及完全閃絡）的發展速度、臨界電弧長度均隨覆冰水電導率的增加而減小。
  5. With the help of this program, this paper does research on the moved backwards of the slide surface, lengthening the anchor section, the soil nail ' s total force, gets conclusion about relations between the soil nail ' s length and the slope ' s grade, height, soil ' s mechanical parameter ; relations between soil nail ' s total force and coulomb soil pressure. with the help of the large multiuse finite element program ansys, this paper analyzes the soil nailing in one - step ' s slopes, in two - steps " slopes, puts the emphasis on the axis force ' s distributing along the soil nail at each rows, the effect of both the excavating mode and the original slope figure to the axis force of the soil nail, the one another effect between the upper - step slope and the nether - step slope in the soil nail ' s axis force, gets conclusion about the design of soil nail at the first low, different slope body is the same with different excavating mode, the original slope figure has more effect to some than others because of the slope body, the reasonably design of the step width in two - steps slopes, the two - steps excavating and retaining has more virtue than the one - step ' s. through soil pressure analysis this paper does research on the differences and the links between the coulomb soil pressure theory and the rankin ' s, the vertical pressure at the slope surface when the slope surface is inclined and the retaining wall is rough, the soil pressure ' s distributing behind the panel, gets conclusion about the effect of both the slope body inner stability and the slope surface local stability to the soil pressure

    通過分析比較，論證了對數螺旋線型比圓弧形作為邊坡的假設滑裂面具有較多的工程優點，並為此編制了一個採用極限平衡法分析土釘支護的fortran語言程序，以此作工具對滑裂面的后移、土釘錨固段的超長、土釘總力的大小等方面作了研究，得出了有關土釘的長度與邊坡的坡角、坡高、土體力學參數的關系、土釘總力與庫侖土壓力間的關系等結論；採用大型通用有限元數值分析程序ansys分別對採用土釘支護的一階邊坡、二階邊坡進行分析，重點是研究各排土釘的軸力分佈規律、開挖方式及原始邊坡形態對土釘的軸力的影響、上下階邊坡在土釘軸力方面的相互作用，得出了有關第一排土釘的設計問題、不同類型的土體應適用於特定的開挖方式、原始開挖出的邊坡形態對一些類型坡體的邊坡土釘支護有較大的影響而對另外一些影響不大、二階邊坡臺階寬度的合理確定、二階開挖及支護比一階時具有較多的工程優點等結論；通過土壓力分析對朗肯、庫侖兩種經典土壓力理論的區別與聯系、坡面傾斜及墻背有摩擦時的坡面豎向應力分佈、面板背土壓力的分佈形態作了研究，得出了邊坡支擋土壓力受坡體內部穩定與坡面局部穩定兩個方面的影響、土釘支護面板背土體中卸荷拱的存在對面板受力有利等結論。
  6. In the past studies of arc - length method, the works mainly focused on the structural geometrical nonlinear analysis. in the case of the application to the material nonlinear analysis of concrete structure, especially when the concrete strain - softening behavior is included in the constitutive model, the studies are limited

    而將弧長法用於混凝土結構的材料非線性分析時，由於餛凝土開裂等因素引起的應變局部化，使得求解存在一定的困難，尤其是當混凝土本構模型中包含應變軟化段時，求解困難更為明顯。
分享友人
分享到 Line

分享到臉書