等溫參數曲線 的英文怎麼說

中文拼音 [děngwēnshēnshǔqūxiàn]
等溫參數曲線 英文
isothermal parameter curve
  • 等 : Ⅰ量詞1 （等級） class; grade; rank 2 （種; 類） kind; sort; type Ⅱ形容詞（程度或數量上相同） equa...
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 參 : 參構詞成分。
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 曲 : 曲名詞1 （一種韻文形式） qu a type of verse for singing which emerged in the southern song and ji...
  • 線 : 名詞1 （用絲、棉、金屬等製成的細長的東西） thread; string; wire 2 [數學] （一個點任意移動所構成的...
  • 曲線 : [數學] curve; bight; bought; profile; net曲線板 french curve; irregular curve; curve board; splin...
  1. In different in terne die travel, the metal flow characterize in warm extrusion forming processes and the affection for the flow of metal stage which made by the difference between the blank bottom altitude and the axial direction limiting size in warm extrusion forming technique have been analysed we have gotten the equivalent strain field and the velocity field and other field variable that the blank in different in terne die travel and the die travel - load curve. at the same time, we have analyzed the contributing factor for the oil pump stator forming process optimized and achieve thereasonable die parameter for the war m extrusion forming finally, the optimized technics parameters were used into pilot production, then the qualified oil pump stator forging were produced, the analog results were compared with those of pilot production

    論文具體分析研究了不同成形工藝過程中金屬流動的特點，並對不同凸模行程下溫擠成形過程中的金屬流動特點、坯料連皮厚度（底部高度）與溫擠壓成形工藝中的軸向界限尺寸的差值對金屬變形階段的影響進行了分析，獲得了坯料在不同凸模行程下的等效應變場、速度場等場變量及凸模行程-載荷曲線，同時對油泵定子成形過程的影響因素等進行了分析，優化並獲得了合理的溫擠成形工藝及模具參數。最後，利用模擬優化獲得的各項工藝參數進行生產實驗，得到實際生產出的合格油泵定子件，並將模擬結果與生產實驗結果進行比較。
  2. This paper studies the application of inductively coupled plasma ( icp ) technology to the etching compound semiconductor insb - in film. by means of single probe and double probe, the ion density and electron temperature of chamber ( 30mm and 50mm in height respectively ) under varied process condition were diagnosed. the spatial distribution of the axial position of the two parameters and the varied curve that the two parameters varies with the power and air pressure are obtained

    利用單探針和雙探針診斷30mm高反應室和50mm高反應室在各種工藝條件下的離子密度和電子溫度，得到這兩個參數在反應室軸向位置的空間分佈、隨功率和氣壓的變化曲線、頂蓋接地和反應室體積對它們的影響，結果表明離子密度為10 ~ 8 10 ~ （ 10 ） cm ~ （ - 3 ） ，電子溫度在4 10ev之間；當頂蓋接地時，該處的等離子體密度明顯大於不接地；在同樣條件下， 50mm高反應室內的離子密度明顯大於30mm高反應室。
  3. The calculation program using the matlab has been worked out to get the numerical solutions of the proposed models. the experiment has first been conducted in the laboratory to get the fundamentals thermal and moisture properties ( such as materials density, specific heat capacity and thermal conductivity ) and also the material moisture absorption isotherms of adobe building materials. the methods of measuring the surface mass transfer coefficient and material moisture content have been proposed

    首次對生土建築材料物性參數進行了實驗測試，得到了常用生土建築材料的密度、比熱和導熱系數等參數值，得到了生土建築圍護結構的等溫吸濕平衡曲線的擬合函數關系式；此外，研究了生土建築圍護結構表面質交換系數實驗測定方法，探索了利用電阻率測量生土建築圍護的安窪築科技人學博十學位論文結構內部含濕量的測試方法。
  4. Under certain conditions, the calculating formula of interlayer stress and the stress - distributing diagram in cut planes are provided, and the mathematical model for warpage deformation calculation is also established

    建立了翹曲變形的數學模型，討論了各種工藝參數（層數、掃描線長、成型室溫度、層厚等）對翹曲變形量的影響。
  5. Based on the constitutive relationship coupled microstructure evolution, 3d - fe simulation of isothermal forging process of tc6 titanium alloy disc is performed dealing with different deformation temperature, punch velocity and shear factor of friction, effect of process parameters on equivalent strain, equivalent stress and grain size is calculated, and load - displacement curve is calculated

    本文基於微觀組織演變的本構關系模型，對不同變形溫度、凸模速度和摩擦條件下鈦合金盤的等溫鍛造過程進行了三維數值模擬，研究了變形工藝參數對等效應變、等效應力和晶粒尺寸的影響，計算了各變形條件下的位移?載荷曲線。
分享友人
分享到 Line

分享到臉書