管座 的英文怎麼說

中文拼音 [guǎnzuò]
管座 英文
socket; vacuum tube base; valve socket; valve panel; valve holder; lamp receptacle; header; base
  • : Ⅰ名詞1 (管子) pipe; tube 2 (吹奏的樂器) wind musical instrument 3 (形狀似管的電器件) valve;...
  1. Material receiving inspection number and steel grade shall be stamped on the heads, shells and downcomer nozzles

    封頭、筒體和集中下降管座上必須打上工廠的材料檢驗編號和鋼號。
  2. Bases for gm counter tubes - interrelationship of quartz - fiber electrometer type exposure meters and companion exposure meter chargers

    蓋革-米勒計數管座.石英纖維靜電計式曝光表和相似曝光表的相互關系
  3. Electron tubes, bases, caps, and terminals including gages, dimensional characteristics of

    電子管座帽及
  4. Lamp holder lamp jack lamp base lamp cap socket pin cap

    管座燈頭燈泡頭
  5. Fixed railway installations. equipment for overhead telecommunication and signalling lines. reinforced concrete socles

    鐵路固定設備.通信和信號線路架空線用設備.鋼筋混凝土製管座
  6. Road vehicles - hydraulic braking systems - double - flare pipes, tapped holes, male fittings and tube seats

    道路車輛.液壓制動系統.雙擴口,螺紋孔,外螺紋接頭和管座
  7. This paper places emphasis on the reheater pipes " basement and wye pipe, which are studied through onsite experience and numerical calculating method. onsite pipes " temperature has been measured by high precise thermocouple

    據分析這是由於熱應力引起的,為此本文對再熱器集汽箱向空排汽管座及三通管座的溫度場及熱應力進行了實驗和數值計算分析研究。
  8. Bases for gm counter tubes

    蓋革-繆勒計數管座
  9. Branchpipe - holder for nominal pressure 16

    標稱壓力為16的支管座
  10. Silicon - light - pipe black ceramics pipe saddle

    硅光黑瓷管座
  11. Forged branch outlet fittings - socket welding, threaded and butt - welding ends

    鋼制承插焊螺紋和對焊支管座
  12. Counting tube base and counting tube holder up to 3 kv ; principal dimensions

    3kv以下的計數管座和計數托架.主要尺寸
  13. Fusewire socket series

    保險絲管座
  14. Ductile iron pipes and fittings - push - in joints - survey, sockets and gaskets

    可鍛鑄鐵道和配件.插入式連接件.測量管座和密封
  15. Straight pattern valves with flange socket placed in shunt - part 1 : without lining

    分流器法蘭密封管座的直排型閥門.第1部分:無襯
  16. The screw - shell of plug - fuse type fuseholders and the contact of a post - extractor fuseholder adjacent to the mounting surface ( unless the post - extractor fuseholder is of deadfront construction ) shall be connected to the load side of the circuit

    臨近盤面安裝的插拔式保險管座的擰動式外殼和柱狀拔出式保險管座的接頭應該接到電路的負荷端上
  17. Plastics piping systems. glass - reinforced thermosetting plastics components. test methods to prove the design of cemented socket - and - spigot joints

    塑料道系統.玻璃纖維增強式熱固性塑料元件.檢驗膠合管座套筒接頭設計的試驗方法
  18. Plastics piping systems. glass - reinforced thermosetting plastics components. test methods to prove the design of rigid locked socket - and - spigot joints with elastomeric seals

    塑料道系統.玻璃纖維增強式熱固性塑料元件.檢驗帶有彈性密封件的剛性鎖定管座套筒接頭設計的試驗方法
  19. En1123 - 2 pipes and fittings of longitudinally welded, hot - dip galvanized steel pipes with spigot and socket for waste water systems. part 2 : dimensions

    廢水系統帶插端和管座的徑向焊接熱浸電鍍鋼道和配件.第2部分:尺寸
  20. En1123 - 1 pipes and fittings of longitudinally welded hot - dip galvanized steel pipes with spigot and socket for waste water systems. part 1 : requirements, testing, quality control

    廢水系統帶插端和管座的徑向焊接熱浸電鍍鋼道和配件.第1部分:要求,試驗和質量控制
分享友人