簧下質量 的英文怎麼說

中文拼音 [huángxiàzhíliáng]
簧下質量 英文
unsprung weight
  • 簧 : 名詞1. [音樂] （樂器里能發聲的薄片） reed2. （器物上有彈力的機件） spring
  • 下 : 下動詞1. （用在動詞后,表示由高處到低處） 2. （用在動詞后, 表示有空間, 能容納） 3. （用在動詞后, 表示動作的完成或結果）
  • 質 : Ⅰ名詞1 （性質; 本質） nature; character; essence 2 （質量） quality 3 （物質） matter; substance;...
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 質量 : 1 [物理學] mass 2 （產品或工作的優劣程度） quality 3 economy （離子源的）; 質量標準 quality level...
  1. The results showed that : ( 1 ) the models used by author and the analysis are useful and can be practiced. ( 2 ) after using isolation technology, the structure ' s period, earthquake response, base shear force and acceleration are all decreased markedly and the horizontal displacement focuses on isolation layer. ( 3 ) under frequent earthquake action, the shear force ratio between layers is close to 0. 35 ; in according with the provision in aseismic design code that the horizontal seismic reduction coefficient can choose 0. 53 and the upper building can be designed by decreasing one degree

    計算模型分別採用三維空間模型及規范中建議的彈簧、質量模型，隔震層採用疊層橡膠隔震支座，運用大型結構有限元計算程序sap2000以及自主開發的nba結構程序計算隔震結構在多維地震動輸入下的動力非線性時程反應，同時研究了隔震結構在溫度變化的作用下，結構各桿件的內力變化，通過對變電建築物在傳統抗震作用下及隔震作用下的分析比較，得出一些有益的結論。
  2. The research result indicated : for the strip primary mirror discussed in this article, the hexagon light - weighted cell has the best structural rigidity quality, the square cell is a little worse, the triangle cell is the worst ; there is an optimum on primary mirror thickness ; on condition of 1g gravity load combining with 4 centigrade uniform temperature rising, the thinner and higher of the flexible support reed, the better of the primary mirror surface figure. the decision of the structural parameters of the flexible support reed must take static rigidity, dynamic rigidity, static strength and dynamic strength of primary mirror assembly into account

    研究結果表明：對于本文的長圓形主鏡，採用正六邊形輕量化孔，鏡體結構剛性品質最好，正方形次之，正三角形最差；主鏡鏡體厚度存在最佳值；主鏡組件在1g重力、均勻溫升4共同作用的工況下，主鏡柔性支撐簧片厚度越小、高度越高，主鏡綜合面形誤差（ p - v值）越小，但同時主鏡組件的剛體位移增大、固有頻率下降，因此柔性支承結構參數的確定要綜合考慮主鏡的綜合面形誤差和主鏡組件靜態剛度、動態剛度、靜態強度和動態強度等因素。
  3. The acceleration response of the sprung mass for the quarter vehicle model the suspension system under periodical excitation and certain road uneven random excitations were discussed

    為了反映實車狀況，著重討論了在調和激振和隨機路面激振下變剛度彈簧懸架簧載質量的動態相應特性。
  4. The titanium alloy valve is more superior than ordinary steel valve in lighter, smaller thermal expansion coefficient, lower in thermal expansion, fatigue durable, good elasticity, and reduces oil consumption so as to prevent instability while revolving at high speed and obtain perfect performance

    鈦合金汽門彈簧比一般鋼閥材質更輕巧、熱膨脹系數小、熱量傳導擴散更低、耐疲勞、彈性佳、減少油耗，以阻止在高速運轉下的不穩定以獲致最完美的性能表現。
  5. The longitudinal stresses in the tunnel structure calculated by using the model of tamura & okamoto are obviously greater than the stresses in transverse direction obtained by using two dimensional finite element analysis. it is proposed that the axial and bending stresses should not be ignored for the underground structural design

    計算結果表明，由彈簧質量模型算得的地下結構在地震作用下縱向振動和橫向振動產生的縱向和彎曲正應力及剪應力明顯高於由二維平面有限元算得的橫向平面內產生的正應力和剪應力，由此可見軸向應力和彎曲應力是地下結構抗震設計中不容忽視的因素。
  6. Foot power shear features : 1 simple construction with a sliding guide 2 adjustable and reliable control with a tread pull spring which is point fixed inside 3 some machines have press sheet units to ensure the high quality cut, light and easy to move 4 widely used in manual sheet feeding

    本機床外形美觀，結構新穎，採用滑動導軌，踏拉簧採用滑動支點固定式，使其操作力減少三分之二，部分機床配有壓料裝置，剪切質量高並有重量輕，移動方便的特點，廣泛適用於金屬薄板工業的人力剪下料。
  7. The calculated results show that with the vibration of the mini - spring the pressure on the electric conducting rod may change periodically

    在考慮彈簧質量的情況下建立了彈簧和導電桿之間的物理模型。
  8. Abstract : the inertial effect of three - point bend specimens under impactloading was analyzed by using the spring - mass system model and an expression for the correction of inertial force was obtained under the condition of brittle fracture of materials

    文摘:用彈簧質量模型分析了三點彎曲試樣在沖擊載荷作用下的慣性效應，得到了脆性斷裂條件下有效載荷的修正公式。
分享友人
分享到 Line

分享到臉書