粒間接觸應力 的英文怎麼說

中文拼音 [lìjiānjiēchùyīnglì]
粒間接觸應力 英文
grain-to-grain stress
  • 粒 : Ⅰ名 （小圓珠形或小碎塊形物） small particles; grain; granule; pellet Ⅱ量詞（用於粒狀物）
  • 間 : 間Ⅰ名詞1 （中間） between; among 2 （一定的空間或時間里） with a definite time or space 3 （一間...
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 應 : 應動詞1 （回答） answer; respond to; echo 2 （滿足要求） comply with; grant 3 （順應; 適應） suit...
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Copper - nanosized tibi composites were prepared by in - situ process. the microstructure, mechanical and electrical properties, and dry sliding wear behavior and electric sliding wear of cu - nanosized tib _ 2 in - situ composites was investigated ; mostly task as follows : the thermodynamic data for the reactions between b and ti in the molten liquid of copper were analyzed, the copper matrix composites reinforced by in - situ tibi nanoparticles were prepared by reactions of 8263, carbon and titanium in copper - titanium melt, and copper - titanium, copper - boron in alloy melt, respectively, which controlled the reaction temperature, reaction time and solidification process. the rnicrostructure and mechanical and electrical properties of the in - situ composites were investigated by using optics microscope, tem and xrd

    本文採用原位反應法制備了cu -納米tib _ 2原位復合材料，在此基礎上分析了原位復合材料的微結構，進行了干滑動摩擦磨損和電接觸滑動磨損實驗，完成的主要工作如下：從熱力學的角度出發，分析了陶瓷tib _ 2顆粒在銅基體中原位生成的熱力學條件，並用電解銅、工業純鈦、 b _ 2o _ 3 、 c （還原劑）以及cu - ti 、 cu - b等合金為原料，通過控制適當的反應溫度、反應時間和快速凝固等工藝手段，制備了cu -納米tib2原位復合材料。
  2. Three models are proposed as follows by applying the model of " mixed flow " : the stress of increasing fluid on fouling, collision between solid particles and fouling, and solid particles movement velocity ; the effects of operating parameters, properties of particles, and the volume fraction of particles on stress in solid - liquid two phase flow, collision stress between solid particles and fouling, maximal contacting area between solid particles and fouling and maximal contacting time between solid particles and fouling are investigated systematically by calculating and theoretical analysis

    利用「混流」模型，建立了兩相流體的剪應力模型、固體顆粒與垢層的碰撞模型和固體顆粒的運動速度模型；通過計算和理論分析，系統地考察了操作參數、顆粒物性、顆粒體積分率等對固液兩相流剪應力、顆粒對垢層的碰撞力、顆粒與垢層的最大接觸時間和最大接觸面積的影響。
  3. It was considered that, the substituted ti reacted with ni3al in - situ and a layer of mo solid solution was formed around the tic particles, which decreased the solid - liquid surface tension between ni3al - tic, leading to the decreasing of wetting angle

    摻入mo後置換出的ti與ni _ 3al發生原位反應，在tic顆粒周邊形成一個含mo的固溶殼層，降低了ni _ 3al - tic之間的液-固表面張力，導致了接觸角的下降。
分享友人
分享到 Line

分享到臉書