粘著度 的英文怎麼說

中文拼音 [niánzhāodù]
粘著度 英文
adhesiveness
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 著 : 著助詞1. （表示動作的持續） 2. （表示狀態的持續） 3. （用在動詞或表示程度的形容詞後面, 加強命令或囑咐的語氣） 4. （加在某些動詞後面, 使變成介詞）
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 粘著 : stick together; adhere;bond;agglutination; [工業] adhesion粘著力 adhesion force; 粘著強度 adhesio...
  1. The material must be moderately coherent and firm.

    材料必須有適度的粘著力和堅固性。
  2. It has been discovered that ( 1 ) in the region between 100 - 350 the friction coefficient is lowering along with the swing of temperature ; ( 2 ) the friction coefficient is the highest at the temperature of 500, and adhesive wear occurred ; ( 3 ) the global graphite grain layer appeared at the surface of wear scar at 450n and 300, and played an extremely good effect of lubrication, thus makes a fairly lower wear at the temperature of 300

    發現： （ 1 ）在100 ~ 350區間，隨溫度的升高，摩擦因數在降低； （ 2 ）在500時，摩擦因數最高，且發生了粘著磨損； （ 3 ）在450n ， 300時，磨痕表面出現了球狀的石墨顆拉層，這起到了極好的潤滑作用，使得300時，磨損較低。
  3. It is different from under point contact that there is no stick area under line contact in the partial slip regime, and load distribution within line contact area is uneven due to roughness of surface

    磨痕分析表明，承載區域接觸不均勻，存在虛接觸區域，其大小與表面粗糙度有關，而接觸區域沒有不磨損的粘著區，不同於點接觸形式。
  4. It is observed that the topography of the area with noise on a scar surface is characterized by larger surface roughness, plowing grooves, pits or adhesive joined asperities. while it is found that the topography of the scar after noise disappearance is characterized by a clear polished scar surface and a smaller surface roughness

    有噪聲磨痕形貌的特徵是表面粗糙度比較大、存在不規則的犁溝、麻坑或粘著微凸體；而噪聲消失后的磨痕形貌特徵是表面粗糙度比較小、有微拋光作用發生。
  5. Self adhesive tapes - measurement of unwind adhesion at low speed

    自粘膠帶.低速度剝離粘著力的測量
  6. Standard test method for bond strength of ceramic tile to portland cement

    瓷磚和硅酸鹽水泥粘著強度的標準試驗方法
  7. Test method for bond strength of latex systems used with concrete by slant shear

    使用斜剪切法測定同混凝土一起使用的乳膠粘著強度的測試方法
  8. Self adhesive tapes - measurement of bonding of thermosetting adhesive tapes after curing ; german version en 12033 : 1996

    膠粘帶.熱硬化后膠粘帶粘著強度測量
  9. Self adhesive tapes - measurement of bonding of thermosetting adhesive tapes during curing ; german version en 12032 : 1996

    膠粘帶.熱硬化中膠粘帶粘著強度測量
  10. ( 2 ) it is found that distilled water as lubricant can markedly reduce the accumulation of friction heat and temperature rise on the frictional surfaces of polymer. so the heat fatigue and adhesive wear decrease. moreover, a lubricating film forms on the interface between the counterpart and polymer when distilled water acts as polar lubricant

    （ 2 ）潤滑劑水的存在，可大幅度降低聚合物磨損表面的摩擦熱積累及溫升，從而減少了基體的熱疲勞磨損和粘著磨損，同時，水作為一種極性潤滑劑，在摩擦界面上能形成一層潤滑膜，對摩擦表面起了一定的隔離作用。
  11. Results of the experiments showed that the wear mechanisms of the sintered steel included abrasive wear, adhesive wear and fatigue wear, and it was the abrasive wear most important. it was the sintered steel mixed by ni, mo that was the best on the wear resistance, because of the great lot of bainite ; the sintered steel quenched and low temperature tempered mixed by mo, w that was the best on the wear resistance, because of the rigidity of the steel was the highest

    實驗結果表明：本文中幾種燒結鋼的磨損機制均是由磨粒磨損、粘著磨損、和疲勞磨損共同作用的，且以磨粒磨損為主；在燒結態下，復合添加合金元素鎳、鉬的燒結鋼的耐磨性能最好，這是因為生成了大量的硬質相貝氏體；而淬火、低溫回火態下，則復合添加鉬、鎢的燒結鋼的耐磨性能最好，這是因為熱處理態下添加鉬、鎢的燒結鋼的硬度最高。
  12. According to some hypothesis about tool surface, the relationship among the friction, roughness and hydrostatic stress was derived, and the limited hydrostatic stress was got when the sticky friction takes place

    同時，根據對工具表面的某些假設，推導了摩擦應力與粗糙度和靜水壓應力等之間的關系，並求出了發生粘著摩擦所需的靜水壓應力。
  13. This phenomenon shows that stick - slip motion and negative friction - velocity slope are not responsible for the present squeal. it is because these two generation mechanisms of squeal only govern the tangential vibrations

    這個現象否定摩擦噪聲發生的兩個機理：粘著-滑動機理和摩擦力-相對滑動速度負斜率機理，因為這兩個機理描述的是切向發生的摩擦振動。
  14. The proposed wear mechanisms of the materials without oil lubrication were the followings : the wear mechanisms of the ferroalloy are adhesive wear, abrasive wear, and some oxidation wear. the wear mechanisms of the composites are abrasive wear and the brittle peeling off. the abrasive wear and the brittle peeling off incr eased with the increase of sic particles content in the composites

    在無潤滑條件下，通過對磨痕形貌的觀察，認為鐵基合金的磨損機理主要是粘著磨損和磨粒磨損，同時伴隨有一定程度的氧化磨損；加入sic後主要是磨粒磨損和脆性剝落，且sic越多材料的脆性剝落越嚴重。
  15. 3 stable adhesive strength can be obtained with a variety of smd

    對于各種表面粘著零件，可獲得安定的接著強度。
  16. Aircraft industry. synthetic cloths for the fabric of airplane structures. determination of shear sstrength by stretching cloths, in the delivery condition, stuck then protected before and after aging

    航空工業.飛機結構用合成纖維布.發貨時測定老化前後粘著保護的拉伸纖維的抗剪切強度
  17. Teraoka ' s packing tapes exhibit highly effective adhesion

    Teraoka包裝用膠帶具有高度有效的粘著力。
  18. Methods of test for mortar for masonry - part 12 : determination of adhesive strength of hardened rendering and plastering mortars on substrates

    圬工灰漿試驗方法.第12部分:襯底上的硬化打底和粘著灰漿粘結強度測定
  19. Building and construction sealants with movement accommodation factors greater than 25 % - method of test for determination of adhesion cohesion properties at variable temperatures

    移動適應因數大於25 %的房屋和建築物密封劑.在可變溫度下粘著特性的測定的試驗方法
  20. Test method for adhesion of pressure - sensitive tape to fiberboard at 90 degree angle and constant stress

    90度角和固定應力條件下壓合帶與纖維板的粘著性的試驗方法
分享友人
分享到 Line

分享到臉書