糙瓷 的英文怎麼說
中文拼音 [cāocí]
糙瓷
英文
rough porcelain-
Products that are always characterized by inventive finishes and new textures : satin surfaces flecked with shimmering chips of stone, resin cements, tumbled vit ? 鄄 reous quartzite, brushed wood, careful sanding
陶瓷產品也一直被拋光工藝以及新的紋路賦予個性特徵，比如緞面、污點石面、樹脂加固、糙石英玻璃、絨面木、以及砂紙精細研磨。Surface roughness prediction of electrical discharge machining ceramics based on evolutionary neural network
陶瓷材料電加工表面粗糙度的預測With a rugged ceramic body and seal construction, along with an internal reflector, cermax xenon lamps are a safe and compact alternative to conventional quartz lamps
與普通的石英燈相比， cermax氙燈具有粗糙的陶瓷體及密封結構，並裝有內置反光燈，是一種更安全的產品The results show that under the same lapping conditions the si3 n4 ball has the lowest material removal rate and the best roundness and roughness, followed by zro2, al2o3, and sic ball
結果表明：在相同的研磨條件下，具有長柱狀晶粒的氮化硅陶瓷球加工速率最低，但圓度和表面粗糙度最容易控制；氧化鋯和氧化鋁陶瓷球表面質量次之，碳化硅陶瓷球加工速率最高，圓度和表面粗糙度最難控制。The influence of surface treatment ( surface polish ) on the flashover performance has been investigated with different kinds of alumina ceramics. it was found that the surface roughness could be used as a reference value for evaluating the influence of surface polish to a certain degree. the experimental results show that the samples with a rougher surface ( polished by sic ) have a worse flashover performance
試驗發現，在一定程度上，表面粗糙度可以作為一個評價表面研磨處理對材料沿面閃絡特性影響的指標，採用碳化硅磨料對氧化鋁陶瓷進行處理后，如果材料的表面粗糙度越高，則其沿面閃絡電壓越低。Advanced technical ceramics - monolithic ceramics - general and textural properties - determination of surface roughness
高級工業陶瓷.塊體陶瓷.一般和紋理特性.表面粗糙度的測定Advanced technical ceramics. monolithic ceramics. general and textural properties. determination of surface roughness
高技術陶瓷.整體陶瓷.一般性能和結構性能.第4部分:表面粗糙度測定On the condition of the test, the cutting force of ticp / fe composites was more than which of 45 steel by 60n, and the cutting temperature was higher than which of 45 # steel by 90, and the roughness of machined surface was almost as much as which of 45 # steel. tic ceramic particles enhanced the cutting force and the cutting temperature of ticp / fe composites, but had little effect on the roughness of machined surface. the machining quality of ticp / fe in situ composite was similarity to 45 # steel
在本試驗條件下，原位tic _ p fe復合材料切削加工時的切削力與45 ~ #鋼相比要大60n ，切削溫度要高90 ，加工表面粗糙度與45 ~ #鋼相近； tic陶瓷顆粒使原位tic _ p fe復合材料切削加工時的切削力增大、切削溫度增高，對加工表面粗糙度影響不大；原位tic _ p fe復合材料的可加工性與45 ~ #鋼相當。分享友人