級聯放大 的英文怎麼說
中文拼音 [jíliánfàngdà]
級聯放大
英文
cascade amplicification-
In the circuit, using the way of step - by - step magnify, a normal sine wave signal through former circuit export for the next circuit, and this signal that have been magnified push the next step. the main magnify circuit use the method of high power dynatron that is parallel connection
在迴路中採用逐級放大的方法，將一個標準的正弦波信號通過前級放大，輸出給后級，推動后級放大迴路，主要的功率放大迴路中採用大功率三極體並聯實現功率放大輸出。In the forth chapter the series negative feedback and interstage mismatching are presentation, and a low noise amplifier whose operating frequency is 1. 5ghz 1. 8ghz is developed
第四章詳細介紹了源極串聯負反饋和級間失配法，並設計和製作了1 . 5ghz 1 . 8ghz低噪聲放大器。The three - order modulator has a 2 - 1 cascaded structure and 1 - bit quantizer at the end of each stage, the modulator is implemented with fully differential switched - capacitor circuits. and then, the discussion will begin by exploring the design of various circuit blocks in the modulator in more detail, i. e., ota, switched - capacitor integrator, quantizer, two - phase non - overlapping clock signal, etc., at the same time, these circuits will be simulated in spectre and hspice. at last, the whole cascaded modulator will do behavioral level simulation by matlab soft and simulink toolbox
本論文中，首先介紹模數轉換器的各種參數的意義，以及一階sigma - delta調制器和高階sigma - delta調制器的原理;給出解決高階單環sigma - delta調制器不穩定性的方案，引入級聯結構調制器，特別針對級聯結構調制器中的失配和開關電容積分器的非理想特性進行詳細的討論;本設計的sigma - delta調制器採用2 - 1級聯結構和一位量化器，調制器採用全差分開關電容電路實現;同時對整個調制器的各個模塊進行了電路設計，包括跨導放大器、開關電容積分器、量化器、兩相非交疊時鐘等，並利用hspice和spectre模擬工具對這些電路進行模擬測試;最後，利用matlab軟體和simulink工具對整個級聯調制器進行行為級模擬。However, everybody ' s mind is already set on next season which should see the bianconeri competing for the top positions in the italian topflight, even though didier deschamps is cautious on juve ' s scudetto chances for next year
然而，每個人的心思都已經放到下賽季去了，大家想知道斑馬軍團回到頂級聯賽后是否有足夠的實力在積分榜前列立足，即使迪迪埃?德尚對明年尤文奪取意甲冠軍的可能性保持謹慎的心態。The amplified spontaneous emission ( ase ) is studied. both the forward and backward ase is simulated and their characters are analyzed in detail. then the dual stage cascade structure is presented as a solution to reduce the ase noise
2 .研究了edfa中放大的自發輻射噪聲光（ ase ） ，詳細分析了前後向ase噪聲光的性質，在此基礎上，提出了雙段級聯結構抑制ase噪聲光，並對這種方法進行了理論和實驗研究。Cascaded transistor amplifier
級聯晶體管放大器The rf receiver consists of rf front end and baseband regulation module. the high - intermediate - frequency superheterodyne structure is adopted in the final scheme. the fine sensitivity of the receiver is achieved by two cascaded lna in the front of the system
系統採用超外差式變頻結構設計，兩級低噪聲放大單元級聯保證了接收機靈敏度，兩級增益控制單元實現了所要求的接收機動態范圍，並且整機的線性度也得到了保證。Based on our theoretical predictions, we find optimal splicing parameters on fsm - 30s fiber splicer for low loss joints between erbium doped fiber and other single mode fibers. we also experimentally demonstrate a novel three - stage erbium - doped fiber amplifier with high gain, low noise figure, and high output power. finally, a prototype of a gain - clamped fiber amplifier is obtained with high gain ( 26 db ), low noise figure ( 5. 3 db ), high output power ( 17 dbm ), and large bandwidth ( 31 nm )
文章研究了摻鉺光纖（ edf ）與其他光纖低損耗焊接問題，得到光纖熔接機低損耗熔接的最佳參數，這對摻鉺光纖放大器的科研生產具有一定的指導意義；研究了新型的三段級聯泵浦優配的摻鉺光纖放大器的優化光路結構，得到高增益，低噪聲，大輸出功率的摻鉺光纖放大器；最後研製成功高增益（ 26db ） ，低噪聲（ 5 . 3db ） ，大輸出功率（ 17dbm ） ，寬帶（ 31nm ）增益箝制摻鉺光纖放大器樣機。Become a kind of new electronics circuit - current - mode circuit. it is replacing the traditional design method of the voltage - mode in the high frequency high - speed signal processing realm 。 this thesis mainly discussed the modified second - generation current conveyors based on the current - mode kinds of new cuicuit components, they are stronger modified standard current - mode parts in fuctions on this foundation. mainly including the modified differential difference current conveyor ( mddccii ) 、 the fully balanced second generation current conveyor ( fbccii ) 、 ( full balances ) four - terminal floating nullor ( fbftfn ) and the current differencing buffered amplifier ( cdba ), they are all function very strong standard current - mode parts, they all can provide some circuit functions of better than general operation amplifier, because they have the voltage importation and the current importation, therefore use it since can carry out the voltage - mode signal processing circuit expediently, can also carry out the current - mode signal processing circuit expediently, and have to increase the benefit bandwidth to accumulate more widely than the voltage - mode, but have their advantages more according to the current - mode filter of the modified current conveyor, because it constitutes in brief, the filter wave function is stronger and they are better than in general use operation amplifier of many advantages, be easy to composing for example 、 high speed 、 frequency bandwidth 、 the power supply voltage requests low 、 consume small, the impedance is different from etc. advantages, otherwise they have biggish dynamic range, and flexible circuit synthesize, so they are the best active parts
從第二代電流傳輸器ccii入手，重點研究了以下幾種改進型的第二代電流傳輸器:改進的差動差分電流傳輸器mddccii 、全平衡第二代電流傳輸器fbccii 、多輸出四端浮地零器ftfn 、全平衡四端浮地零器fbftfn 、電流差分緩沖放大器cdba的電路結構及其模型。然後在此基礎上系統地研究了基於這幾種改進型的第二代電流傳輸器的濾波器的設計方法，主要方法和結果如下:利用mddccii設計了差分式連續時間電流模式低通、帶通濾波器;電流模式跳耦結構考爾低通濾波器;利用fbccii設計了帶通二階節濾波器及電流模式雙二階通用濾波器;設計了基於多輸出端ftfn的電流模式二階通用濾波器電路;通過數字化開關選擇的基於fbftfn的電流模式通用濾波器;設計了基於最少個數電流緩沖放大器（兩個cdba ）的多功能通用電流模式濾波器及其在非理想因素情況下分析。設計濾波器的主要方法是採用級聯設計、運算模擬（信號流圖法）和反饋設計（跳耦法） 。The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier
本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。The results show that wavelength locates in gain zone of semiconductor optical amplifier, and have higher peak power and proper time delay between the two pulses for the second order super gauss control pulse in semiconductor optical amplifier. a high quality amplified signal pulse can be achieved. the chirp can be reduced notability by using cascading soa in cross gain modulation based on soa, and the distance and the peak power of conversion optical pulse can be increased notability, and we can let down the demand for wavelength based on xgm in soa and enhance the flexibility of wavelength conversion
我們應用二階超高斯光脈沖與高斯信號脈沖同時注入soa和應用soa與非線性光學環鏡（ nolm ）相結合的方案來對信號脈沖進行壓縮整形，模擬顯示，在調節系統合適參數的情況下，波長位於soa增益區的二階超高斯控制光脈沖在具有較高的峰值功率和適當時延下輸入soa時，最後可以得到放大的高質量超簡訊號光脈沖；在基於soa的交叉增益調制（ xgm ）全光波長轉換中，採用級聯的soa能有效地使反轉光脈沖的頻率啁啾得到有效降低，波長向下轉換的距離和反轉光的峰值能量都得到明顯提高，降低了利用交叉增益調制（ xgm ）波長轉換中對波長精度的要求，從而提高了波長轉換的靈和性。Computer control unit produces the trigger pulses for the fast switching thyristors. fast switching thyristors are connected in parallels in order to meet the capacitance requirement of the circuit. trigger pulses produced by computer are amplified and isolated by three pulse transformers
設計三級脈沖變壓器來隔離和放大計算機產生的觸發脈沖，得到強觸發信號滿足了多個快速晶閘管並聯觸發的功率要求以及系統的抗反擊電壓的要求。The chip is accomplished in the full cooperation with other team members, the author pays particular attention to the analysis of the whole chip architecture and three sub - block design : transconductance amplifier ( ota ), voltage reference and current reference. based on existed technologies, a new high order temperature compensated voltage reference and a creative current reference with high order temperature compensation are shown respectively. the author simulated all the sub - block and whole chip by hspice
該晶元的設計是由小組成員共同完成，本人主要負責了總體電路的分析、聯合模擬驗證及以下三個子電路的設計: 1 、跨導放大器，詳細分析了bandgap跨導放大器輸入級的動靜態特性及其優缺點，並結合系統要求，設計了一種與cmos工藝相兼容、可替代bandgap跨導放大器的低壓共源共柵跨導放大器。In this paper, the traditional cascode structure of cmos lna is considered as a two - stage amplifier and inter - stage matching network is introduced accordingly
本文也對cmos低噪聲放大器進行了分析，將傳統共源共柵結構看作二級放大器級聯形式，並由此引入級間匹配網路。For the system application, we cascade multi - module to satisfy the system ’ s demands. the measured results of fabricated limiting amplifier are in agreement with eda simulation results. the experimental results indicate that the x - band limiting amplifier can satisfy performance demands of x band receiver
本課題採用了模塊化的設計方法，首先設計限幅放大器模塊電路，經製作、調試，得到能滿足級聯要求的、性能穩定的模塊電路;然後根據限幅放大器整體系統指標的要求，多級模塊級聯組成限幅放大器整體電路。The amplifier adopted the three - stage structure, and the first stage used one chip, the second stage used two chip in parallel, the third stage used four chip in parallel
該功放模塊採用三級放大結構，第一級採用一個管芯，第二級並聯兩個管芯，第三級並聯四個管芯。Cascaded brillouin scattering in a distributed fiber raman amplifier
光纖拉曼放大器中級聯的前向受激布里淵散射Cascaded stimulated brillouin scattering in a distributed fiber raman amplifier
光纖拉曼放大器中級聯的受激布里淵散射The cascadability of semiconductor optical amplifier based optical space switches
基於半導體光放大器的開關矩陣級聯規模的研究It is possible that they may modify the existing signal transduction procession in cell membrane, thus producing both transduction and biochemical amplification of the effects of the field itself
因此一般認為電磁場可能通過作用於細胞膜上業已存在的信號轉導途徑，將物理信號轉化成生物信號，進而經過信號轉導及生物級聯放大，最終產生生物效應。分享友人