結晶粘合劑 的英文怎麼說

中文拼音 [jiējīngniángějì]
結晶粘合劑 英文
crystalline binder
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 晶 : Ⅰ形容詞（光亮） brilliant; glittering Ⅱ名詞1. （水晶） quartz; （rock） crystal 2. （晶體） any crystalline substance
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 結晶 : 1 （析出晶體） crystallize2 （晶體） crystal 3 （成果） crystallization; fruit; product; quintess...
  • 粘合劑 : adhesie cement
  1. The results show that the dynamic elastic modulus, loss modulus and complex viscosity of the nanocomposite are higher than those of pp, while the loss factor is lower, that the complex viscosity of the nanocomposites is more sensitive to temperature, and that the flow activation energy and the crystallization temperature increase respectively by 15 % and 10k as compared with pp, which may contribute to the enhanced interfacial interaction between pp and ommt resulting from the addition of tmpp

    結果表明：與純聚丙烯相比，納米復合材料具有較高的動態彈性模量、損耗模量和復合粘度，力學損耗因子則降低，納米復合材料的復合粘度對溫度的敏感性略高於聚丙烯；界面改性劑的加入增強了有機蒙脫土與聚丙烯的界面作用，與聚丙烯相比，納米復合材料的流動活化能提高約15 % ，結晶峰溫度提高10k左右。
  2. Lactide were investigated. the key factors affecting the polymer intrinsic viscosity were found to be monomer recrystallization times, stannous octoate concentration and polymerization time. the thermal stabilizing agent did not significantly affect the polymer molecular weight. the polymer with a viscosity average molecular weight beyond 200000 was fairly reproducible by optimizing the polymerization conditions. it was found that poly

    單體重結晶次數辛酸亞錫濃度聚合時間等條件均是影響聚合物特性粘數的重要因素。熱穩定劑對聚丙交酯的分子量幾乎沒有影響。優化聚合條件可以獲得粘均分子量大於200000的聚丙交酯材料，聚合結果具有良好的重復性。
  3. It was found that the interfacial bonding of 93w - ofc was both the joining action of ofc / w grains and that of ofc / ni - fe binders, whereas the joining of ofc to tc4 could be seen as the mutual intense diffusion effect between ofc / tc4 and as a result cu - ti intermetallic compounds were formed at the joint. the joining of tc4 - a1 and a1 - mb2 were also attributed to the result of diffusion between elements ti - al and al - mg respectively. on the other hand, residual thermal stress and stress - induced distortion were produced at the joint simultaneously due to the difference in thermal expansion coefficient of different welding " materials

    研究表明， 93w與ofc的界面連接是ofc與93w中w晶粒的連接以及ofc與93w中ni - fe粘接劑的連接共同作用的結果； ofc與tc _ 4連接界面的形成是由於ofc與tc _ 4之間發生反應擴散，並由此在二者接頭處生成了cu - ti金屬間化合物的中間相； tc _ 4 - al的連接與al - mb _ 2的連接則分別是其基體元素ti 、 al之間和al 、 mg之間元素互擴散的結果，另外，由於熱膨脹系數的差異，擴散焊接后在不同焊件的接頭處存在殘余熱應力並由此引起接頭的形變。
  4. The best aluminum borate whisker preform fabrication process without any binder of superior quality magnesium matrix composite is presented by studying whisker washing ; whisker distribution ; preform taking shape ; preform drying and preform calcined technique

    通過對沒有任何粘接劑的硼酸鋁晶須，從晶須的清洗、晶須的分散、預制塊成型、預制塊烘乾及預制塊燒結技術方面進行了研究，提出了獲得用於制備鎂基復合材料的硼酸鋁晶須預制塊的制備工藝。
  5. Through analyzing for requirement of shell strength and various hardeners, good economical benefit has been achieved by using technology of nh4cl and alcl3 crystal mixed hardener with the same binder and refractory staff

    通過對型殼強度性能的要求與不同硬化劑的分析，在粘結劑和耐火材料不變的情況下，應用氯化銨與結晶氯化鋁混合硬化工藝，取得較好的經濟效果。
分享友人
分享到 Line

分享到臉書