給水閘門 的英文怎麼說

中文拼音 [gěishuǐzhámén]
給水閘門 英文
feed water stop valve
  • 給 : 給Ⅰ動詞1 （送對方某物; 使對方得到） give; grant 2 （用在動詞后 表示交與 付出） pass; pay 3 （叫; ...
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 閘 : anchor gate
  • 門 : Ⅰ名詞1 （房屋、車船等的出入口 ） entrance; exit; door; gate 2 （形狀或作用像門的東西） switch; va...
  • 給水 : [機械工程] feedwater; water supply給水泵 feed pump; 給水量 confluent; 給水能力 capacity of water ...
  • 閘門 : 1 （水閘） sluice gate; gate; water gate2 （船閘） lock gate3 [機械工程] throttle valve; strobe; ...
  1. By hydraulic modeling, this paper describes studies on the stability of a floating bulkhead operating in standing water and flowing water, and it ' s hydrodynamic stability characteristics that distinguish in standing water from in flowing water ; and direct measurements of the forces acting on the model floating body during floating and sinking is taken. as a result, the rotation stress curves are produced and analyzed ; to provide data for optimum operation schedule analyses of the sluice, the relationship of the impact forces acting on the side wall of the gate and the running speed is studied ; the reasons of unstably uplifting of the bulkhead are discussed and the method to solve the problem is also given in this paper

    本文結合常州新閘防洪控制工程水工模型試驗，系統分析了浮箱門在靜水和動水中的穩定性及其影響因素，指出靜水穩性和動水穩性的不同特點；試驗測定了浮箱門動水運行時的受力情況，給出並分析了定位過程轉動力的變化過程曲線；根據浮箱門啟閉速度與門體和岸墻之間撞擊力大小的關系，選擇合理的動力設備，為設計和工程實踐提供可靠依據；分析浮箱門難以穩定上浮的原因，並給出解決方案。
  2. Secondly, on the base of the analyzing design characteristic, this paper presents theoretical basis according to " design specification about steel gate in water conservancy and hydropower engineering " ( thereinafter for short specification ). it introduces module design means of hmvcad system. in the light of this means, it develops the module that can design the gate according to original data and specification automatically, the module of making the original design by user ' s experience, the module of majorized adjustment, the module of alarm device

    其次，本文在分析了弧形閘門設計特點的基礎上，按《水利水電工程鋼閘門設計規范》 （ dl t5039 - 95 ，以下簡稱《規范》 ）給出了設計的理論依據，介紹了hmvcad系統的模塊設計方法，據此研製了能根據原始資料自動按規范設計的程序模塊，以及據用戶經驗進行初步設計、優化調整、預警裝置等功能模塊。
  3. The main contents in the paper are as follows : ( 1 ) the operational principle of the hydraulic automatic tilting gates with connecting lever and rolling wheel were analyzed. using block diagram, the author elaborated on the running course and steady factors of the tilting gate. then the instantaneous running center in the running course of the tilting gate was brought forward, and the trochoid of the center was described

    本文研究的主要內容如下： （ 1 ）分析闡述了水力自動翻板閘門的工作原理和運轉機理，結合框圖詳細分析說明了翻板閘門的運轉過程及其穩定條件，給出了閘門在運行過程中的瞬心軌跡線，分析研究了閘門運動過程中的基本平衡方程。
分享友人
分享到 Line

分享到臉書