緊固臺 的英文怎麼說

中文拼音 [jǐngùtái]
緊固臺 英文
aufspanntisch
  • 緊 : Ⅰ形容詞1 （物體受到幾方面的拉力或壓力以後呈現的緊張狀態） taut; tight 2 （物體受外力作用變得固定...
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 臺 : 臺名詞（指臺州） short for taizhou （in zhejiang province）
  • 緊固 : [設計] fastening; fixture緊固桿 anchorage bar; 緊固環 dead ring; 緊固夾 anchorage clip; 緊固件 fa...
  1. The requirement for a good test fixture is maximum stiffness for the lightest possible weight.

    一臺好的試驗固緊裝置應該是重量輕而剛度大。
  2. Fix the cosmetic shelf on the base with the m5 inner hexangular set screw

    將化妝臺用m5的內六角緊頂螺釘固定在底座上。
  3. To add rigidity, braces are sometimes fastened from the overarm to the knee

    為了增加剛性，有時從懸臂到升降臺裝上一對撐臂加以緊固。
  4. Lifting and lowering of the pringting arm of this machine is vertical, therefore, in case of half - tone printing, presence of screen wire and consistency of aberration are improved ; in case of spot printing, stability and uniformity of inking are enhanced ; fine adjustment and lock of the worktable is independent of each other, so positioning error caused by lock of the worktable can be controlled ; height and pressure of the printing blade and ink - returning blade can be stepless - regulated separately, which improver printing quality and service life of half - tone ; printing travel and half - tone fixing mechanism can be fast adjusted, which is suitable for printing area with different size

    本機印刷大臂升降為垂直升隆式，網線版印刷時網線表現率為色差一致性得到提高，實地版印刷的施墨穩定性及均勻性得以加強；工作臺微調與鎖緊獨立，因工作臺鎖緊而帶來的定位誤差得以控制；印刷刀、回墨刀高度及壓力均可單獨無級調節，提高了印刷質量和網版的使用壽命，印刷行程和網版固定機構大小可快速調節，方便不同規格的印刷面積。
  5. Note : when draining table top models, remove the screw securing the drain access cover. remove the cover by pulling down and away from the water heater

    注：對于臺面型熱水器的排水，需要拆卸排水觀察蓋板上的緊固螺絲。通過往下拔將蓋板從熱水器上卸下來。
  6. It is forbidden to hold the work - piece by hand to drill holes. the work - piece must be fixed tightly in jaw vice or fixed it on the worktable with press plate

    禁止用手握住工件進行鉆孔，應該把工件緊固在虎鉗中或用壓板固定在工作臺上。
  7. Attaching the pipe vise to the workbench allows repairs to be carried out quickly and cleanly. struts should never be held in a normal workshop vise due to the risk of deforming the strut - tube

    用途：固定避震器在夾具中，以方便進行工作，夾具可靈活安裝在虎鉗上或用螺絲收緊在堅固的工作臺上維修寶馬減震系統會合用，請看參考圖片。
  8. Qingdao xinhua hardware co., ltd was established in 1987, the speciality produced various kinds of specification standard fastener, non - standard fastener, the cold is hot candied, have abundant production experience and technology, 3000 tons of annual production capacity, 60 production equipments

    青島新華五金製品有限公司，創建於1987年，專業生產各種規格標準緊固件非標準緊固件，冷拔絲，具有豐富的生產經驗和技術，年生產能力3000噸以上，生產設備60餘臺。
分享友人
分享到 Line

分享到臉書